Crestron SRD-CPL-4 Four-Way Coupler Installation Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2008 Crestron Electronics, Inc.
Crestron SRD-CPL-4 Four-Way Coupler Contents Four-Way Coupler: SRD-CPL-4 1 Introduction................................................................................................................................1 Block Diagram.............................................................................................................1 Specifications...............................................................................................................3 Included Items .........................
Crestron SRD-CPL-4 Four-Way Coupler Four-Way Coupler: SRD-CPL-4 Introduction The SRD-CPL-4 is a four-way passive coupler optimized for use in configuring a multi-port splitter using up to four SRD-SPL-4 Four-Way Amplified Splitters (sold separately) as part of a Crestron® XM or SIRIUS® satellite radio distribution network. Four F-to-F cables, 1 foot in length, are included for connection between the SRD-CPL-4 and each SRD-SPL-4, enabling connection to up to 16 satellite radios.
Four-Way Coupler Crestron SRD-CPL-4 SRD-CPL-4 Block Diagram 2 • Four-Way Coupler: SRD-CPL-4 Installation Guide – DOC.
Crestron SRD-CPL-4 Four-Way Coupler Specifications Following are specifications for the SRD-CPL-4. SRD-CPL-4 Specifications SPECIFICATION Input Outputs Loss @ 2.33 GHz Environmental temperature Humidity Overall dimensions: Height Width Depth DETAILS One port (feeds DC power upstream) Four ports (diode protected) -12 dB -40° to 150°F (-40° to 66°C) 0% to 98% RH (non-condensing) 0.64 in 3.44 in 2.10 in (1.63 cm) (8.74 cm) (5.
Four-Way Coupler Crestron SRD-CPL-4 Industry Compliance As of the date of manufacture, the SRD-CPL-4 has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Installation Installation of the SRD-CPL-4 coupler consists of the following. Refer also to the block diagram on page 2. • Attach the RG-6 cable from the antenna to the port labeled IN on the coupler.
Crestron SRD-CPL-4 Four-Way Coupler Problem Solving Troubleshooting The table after this paragraph provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. SRD-CPL-4 Installation Troubleshooting TROUBLE POSSIBLE CAUSES No signal Short circuits reception.
Four-Way Coupler Crestron SRD-CPL-4 SRD-CPL-4 Installation Troubleshooting (Continued) TROUBLE Limited reception or channels available for XM and/or SIRIUS tuners. POSSIBLE CAUSES CORRECTIVE ACTION Problem with tuner card. Ensure that the tuner card is registered/activated.
Crestron SRD-CPL-4 Four-Way Coupler Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Installation Guide – DOC. 6725A (2021575) 08.08 Specifications subject to change without notice.
