Crestron DTT-15V3 DualTouch™ Technology Touchpanel Operations Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2008 Crestron Electronics, Inc.
Crestron DTT-15V3 DualTouch™ Technology Touchpanel Contents DualTouch™ Technology Touchpanel: DTT-15V3 1 Introduction ............................................................................................................................... 1 Features and Functions ................................................................................................ 1 Applications.................................................................................................................
Crestron DTT-15V3 DualTouch™ Technology Touchpanel DualTouch™ Technology Touchpanel: DTT-15V3 Introduction The DTT-15V3 is a 15" touchpanel designed for use with the UPX-2 Universal Presentation System to support all of the control capabilities of a Crestron touchpanel, plus pen-based annotation and computer-based multimedia presentation.
DualTouch™ Technology Touchpanel Crestron DTT-15V3 Enhanced Ergonomics The DTT-15V3 features a completely flat bezel for drawing comfort and reduced overall size. The adjustable stand allows the touchpanel to be tilted between 17 and 73 degrees. The pressure-sensitive pen is both cordless and battery-free for performance and reliability. Versatile Installation Features The DTT-15V3 ships complete with tilt stand, cables, and power supply.
Crestron DTT-15V3 DualTouch™ Technology Touchpanel Specifications Specifications for the DTT-15V3 are listed in the following table. DTT-15V3 Specifications SPECIFICATION DETAILS Touchscreen Display Display Screen Size Resolution Color Depth Contrast Ratio Brightness Viewing Angle TFT active matrix color LCD 15 inch (38.1 cm) diagonal 1024 x 768 pixels (XGA) 16.
DualTouch™ Technology Touchpanel Crestron DTT-15V3 3. When loading VisionTools Pro-e files or firmware through the RS-232 port of the control system, be sure that the baud rate is at 38400 (Cresnet speed) or lower. Otherwise, Toolbox may post the “Transfer Failed” message. NOTE: Crestron software and any files on the website are for authorized Crestron dealers and Crestron Authorized Independent Programmers (CAIP) only.
Crestron DTT-15V3 DualTouch™ Technology Touchpanel DTT-15V3 Physical View 1.91 in (4.84 cm) 11.93 in (30.29 cm) 13.55 in (34.43 cm) DTT-15V3 Physical View – Right Side (Maximum and Minimum Height) 11.49 in (29.19 cm) 11.47 in (29.14 cm) 4.34 in (11.02 cm) 8.57 in (21.77 cm) Operations Guide – DOC. 6632B 12.23 in (31.
DualTouch™ Technology Touchpanel Crestron DTT-15V3 DTT-15V3 Physical View – Rear (Stand Not Shown) DTT-15V3 Connectors, Controls & Indicators 8 6 9 10 6 1 2 3 4 5 7 6 • DualTouch™ Technology Touchpanel: DTT-15V3 Operations Guide – DOC.
Crestron DTT-15V3 DualTouch™ Technology Touchpanel Connectors, Controls & Indicators # CONNECTORS, CONTROLS & INDICATORS USB 1 Pin 1 Pin 2 DESCRIPTION (1) USB B female; USB 2.0 port; Pin 4 Pin 3 2 DC IN (12V) 3 ANALOG RGB OUT Connects to any USB port on UPX-2 using 6 ft (2.
DualTouch™ Technology Touchpanel Crestron DTT-15V3 Connectors, Controls & Indicators (Continued) # CONNECTORS, CONTROLS & INDICATORS 5 PEN TRAY DESCRIPTION Located on the bottom front edge of the touchpanel; Provides a convenient resting place for the pen. When the display stand is set to its lowest position, place your fingers beneath the tray and slide it out. 6 COMMUNICATIONS PORT (2) Communications port for system diagnostics; CAUTION: Do not connect any devices to this port.
Crestron DTT-15V3 DualTouch™ Technology Touchpanel Industry Compliance As of the date of manufacture, the DTT-15V3 has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. NOTE: This device complies with part 15 of the FCC rules.
DualTouch™ Technology Touchpanel Crestron DTT-15V3 Setup Configuring the Touchpanel NOTE: The only connection required to configure the touchpanel is power. Refer to “Hardware Hookup” on page 17 for details. The touchpanel display can be configured using the four setup buttons on the top of the DTT-15V3. Power is required to configure the touchpanel. Refer to “Hardware Hookup” on page 17 for information on connecting power.
Crestron DTT-15V3 DualTouch™ Technology Touchpanel 3. Phase – Use the (-)/(+) buttons to manually reduce horizontal distortion lines. The Reset option to save. is used for automatic adjustment. Press Enter Phase Control 4. Pitch – Use the (-)/(+) buttons to manually reduce vertical distortion lines. The Reset option save. is used for automatic adjustment. Press Enter to Pitch Control 5. Horizontal Center – Use the (-)/(+) buttons to manually move the image left or right.
DualTouch™ Technology Touchpanel 6. Crestron DTT-15V3 Vertical Center – Use the (-)/(+) buttons to manually move the image down or up. The Reset option to save. is used for automatic adjustment. Press Enter Vertical Center Control 7. Menu Position – Use the (-)/(+) buttons to move the menu to one of the available nine positions. Press Enter to save. Default is center position. Menu Position Control 8. Reset – Use AUTO ADJUST to reset only the image parameters (menus 1 through 6).
Crestron DTT-15V3 DualTouch™ Technology Touchpanel 9. Backlight – Use the (-)/(+) buttons to decrease or increase the backlight brightness. Press Enter to save. Default is 80. Backlight Control 10. Color – Provides a color temperature selection of 9300K, 6500K, 5000K, DIRECT (no adjustment to the incoming signal) and a USER option to use the independent RGB adjustment. Click the icon to allow an independent adjustment of red, green and blue. Press Enter to save. Defaults are shown as follows.
DualTouch™ Technology Touchpanel Crestron DTT-15V3 11. Language – Use the (-)/(+) buttons to select a language for the display adjustment menus. Press Enter to save. Default is English. Language Control Supplied Equipment The DTT-15V3 is shipped with the following accessories. • (1) Pen (with five tip replacements) • (1) USB Cable; Approximately 6-feet long. • (1) VGA to VGA Cable; Approximately 6-feet long.
Crestron DTT-15V3 DualTouch™ Technology Touchpanel • (1) Pen Tether and Tether Hardware Installation VESA Mount The DTT-15V3 may be removed from the adjustable stand and remounted to a VESA® conforming mount arm or stand. The Video Electronics Standards Association (VESA) is an international non-profit corporation that supports and sets industry-wide interface standards for the PC, workstation, and computing environments.
DualTouch™ Technology Touchpanel Crestron DTT-15V3 VESA Mounting Rear of DTT-15V3 Alternate Mounting Platform M4 Screws 4 mm wide 0.7 mm pitch 15 mm maximum length CAUTION: When attaching the DTT-15V3 to an alternate mounting platform, be sure to follow all instructions supplied by the manufacturer. Install Pen Tether The pen can be tethered to the DTT-15V3 using the supplied tether and tether hardware.
Crestron DTT-15V3 DualTouch™ Technology Touchpanel Hardware Hookup Refer to the following diagram and complete the connections as specified. Ensure that the UPX-2 and the DTT-15V3 are both powered down before beginning. CAUTION: To avoid damage to the DTT-15V3 or to your video card, never connect or disconnect the video or power cable while the DTT-15V3 or the UPX-2 are powered up. NOTE: The USB cable may be extended using up to four 16-foot active extensions.
DualTouch™ Technology Touchpanel Crestron DTT-15V3 Hardware Connections for the DTT-15V3 KENSINGTON SECURITY SLOT PEN HOLDER VESA MOUNT USB: TO UPX-2 DC IN (12V): FROM POWER SUPPLY ANALOG RGB OUT: TO AUXILIARY MONITOR ANALOG RGB IN: FROM UPX-2 USB ACCESSORY (x2): TO USB KEYBOARD OR USB MOUSE PEN TRAY CAUTION: Do not apply excessive pressure to the touchscreen display during handling. Doing so can crack the screen and damage the touchpanel.
Crestron DTT-15V3 DualTouch™ Technology Touchpanel Replacing Pen Tips The pen comes with five extra tips. The pen tip will wear with normal use. Worn tips feel more drag when you draw, or it seems as if you are scratching the overlay with your pen. It can be easily replaced with one of the extra pen tips. Replacement pens and a 5-pack of replacement pen nibs are available from the Wacom website (http://wacomdirect.wacom.com). 1.
DualTouch™ Technology Touchpanel Crestron DTT-15V3 Using the Pen While working with the DTT-15V3, you can rest your hand on the surface of the display screen, just as if you were drawing on a sheet if paper. The pen is activated as soon as it enters proximity, about 0.2 inches (5 mm) above the surface. This allows you to position the screen cursor before touching the pen tip to the surface. When the pen tip contacts the surface of the DTT-15V3, the tip switch is activated.
Crestron DTT-15V3 DualTouch™ Technology Touchpanel Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. DTT-15V3 Troubleshooting TROUBLE DTT-15V3 does not function. CORRECTIVE ACTION The DTT-15V3 is not receiving power (The Power LED is off). Verify cable connections and power to unit. The DTT-15V3 is receiving power. (The Power LED is on.
DualTouch™ Technology Touchpanel Crestron DTT-15V3 Reference Documents The latest version of all documents mentioned within the guide can be obtained from the Crestron website (http://www.crestron.com/manuals). This link will provide a list of product manuals arranged in alphabetical order by model number.
Crestron DTT-15V3 DualTouch™ Technology Touchpanel Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations Guide – DOC. 6632B (2019290) 03.08 Specifications subject to change without notice.
