CDVS-5400 SERIES DVR 1. Precautions Cautions & Warnings - Be sure to turn off the power before installation. - Avoid rough handling or mechanical shock. - Keep off 20 cm distance with other machines or electronic products. - Keep away from direct rays of the sun or heater or similar devices.(it causes fire) - Don’t put things such as vase, cup, cosmetics, bottle etc. on this product.
CDVS-5400 SERIES DVR 2. Installation System Open the box and make sure that the following accessories are supplied. (Some part and design could be different according to model.) 2.1 Removing Package.
CDVS-5400 SERIES DVR 2.2 Rear panel of System a e f g h i b j k lm n o p c d q r a. Camera Input (CH1~CH16) / Output (CH1~CH16) b. Camera 75Ohm Terminator c. Control Output (Com:4port, Control:16port) d. Sensor Input (Com:4port, Sensor:16port) e. AC Power Input (AC 110 ~ 220V) f. PS/2 Mouse Port g. PS/2 Keyboard Port h. USB Port i. Com A Serial Port j. LPT(Printer) Port k. Com B Serial Port l. Line Out 1 m. Line In / Line Out2 n. MIC In o. Game Port p. VGA Out q. TV Out (Composite Out) r.
CDVS-5400 SERIES DVR 2.3 Connecting outer Devices - Connect keyboard & mouse (included in the box) Connect keyboard and mouse at the correct place like a picture.(picture shows keyboard connection, upper port is for mouse connection) - Connect Camera (cable is not included) Connect camera cable to channel input port. - Connect communication cable(cable is not included) Connect LAN cable or public phone line(if installed) for using client program (such as center & i-DVR).
CDVS-5400 SERIES DVR 2.4 Connect Pan/Tilt control 485 Signal Line (+) a ground Signal Line (-) RX LED (Green) TX LED (Red) Operation LED (Green) - Connect to PAN/TILT Receiver (RS-485 Signal line) - Caution : When connect, pay attention (+), (-) polarity of signal line -6- - Only when Operation LED is ‘On’ state, image appears normally.
CDVS-5400 SERIES DVR 2.5 Connecting PSTN, ISDN, Leased Line & LAN Following picture shows how you connect to a communication line. It shows about LAN connection and PSTN (external modem). When you have modem in your system, you don’t need to use COM2 port for connection. Connecting to COM 2 port ( 9 PIN ) LAN port Ethernet A/C ADAPTER RS-232(25Pin) D.S.U(Modem) Leased Line (ISDN) D.S.
CDVS-5400 SERIES DVR 2.6 Connecting Loopback output (Camera 75 Ohm Terminator) Each channel’s current input image can directly out to monitor by ‘Ch out’ port. 16 ch outputs are available. To use this function, connect cable then adjust dip switch. ON ON - ‘On’ : not connected outer monitor.
CDVS-5400 SERIES DVR 3. Surveillance Mode When every connection is made, turn the power on. After loading OS, it automatically starts DVR program. Initial screen is surveillance mode(see the picture below). In surveillance mode, it shows real time images of each channel from a connected camera. Also user can control other functions with using function buttons. 3.1 Surveillance screen. b) c) a) d) e) g) f) a) Shows current user.
CDVS-5400 SERIES DVR 3.2 Login as Administrator At the first time, program automatically login as default user. To use program with another user, user information must be registered by Administrator. When DVR starts, login as ‘Administrator’ and add users and allow permissions of each user. No password is set to Administrator. After login as Administrator, then change the password and memorize it. Click one of function buttons.
CDVS-5400 SERIES DVR 3.3 Controlling Screen Division When user clicks one of following buttons, screen display will change as selected division. • 4A : Display the screen 1ch ~ 4ch • 4B : Display the screen 5ch ~ 8ch. • 4C : Display the screen 9ch ~ 12ch. • 4D : Display the screen 13ch ~ 16ch. • 9 : Display the screen 1ch ~ 9ch. • 13 : Display the screen 1ch ~ 13ch. • 16 : Display the screen 1ch ~ 16ch. • 6 : Display the screen 1ch ~ 6ch. • 7 : Display the screen 1ch ~ 7ch.
CDVS-5400 SERIES DVR 3.5 Screen Auto Switching To use Auto Switching, click the button(left picture) in a surveillance mode. When you click this button, the divided screen switches automatically. You can set switching time at the setup.(Auto switching is available on 1, 4, 9 division) - How to use Auto Switching 1. Choose screen.(1, 4(a,b,c), 9 division) 2. Click auto switching button 3. To stop, click auto switching button again.
CDVS-5400 SERIES DVR 3.6. Backup The icon left is backup button. If this button is pressed, following picture shows up. This function uses for moving a stored image data from local HDD to other backup media. User can backup image data to other portable media or other HDD. Available backup devices are DVD-RAM, CDRW and IEEE1394 devices. - How to backup - Press backup button, following dialog shows up. - Select date and 10 minute data block.(if selected it turns red) - Select backup media.
CDVS-5400 SERIES DVR 3.7 Controlling PAN/TILT Camera If the PAN/TILT camera installed, you can control camera with following remote control. To do this press the PAN/TILT remote control button(picture in left) then you can control camera. Available function may be varied according to camera. - Direction Control To control camera direction, use arrow buttons. The number in the middle of circle shows currently selected camera number. To change this, click camera image from surveillance screen.
CDVS-5400 SERIES DVR 3.8 Exit (Power Off/ Restart System) The button like a picture is a logout(exit) button. To change current user, you should log off and then log on with other user name. When you need to change Windows setting, select ‘Restart in Window mode’. Restart in Windows Mode - Log On : Log on with other user. - Log Off : Log off current user and Log on with default user. - Power Off : Shut down system. - Restart System : Restart System.
CDVS-5400 SERIES DVR 4. Search With search function, user can find a recorded data more easily than VCR. Our search function provides special features such as Index search & Object search. g) f) e) d) a) b) c) a) Functions in Search mode In search mode. Print, Saving file, Index search, removing after image, object search and Thumb nail preview are available. b) Adjust Bright & Zoom User can adjust brightness and screen size of current stopped image.
CDVS-5400 SERIES DVR c) Select Camera Select camera number, date & time before start search. To select more than one camera, you can use screen division button or choose each cameras you desired to watch.
CDVS-5400 SERIES DVR 4.1 Printing User can print out current image. To print out a image, stop the desired image then press print button.(If printer is not installed, you can’t print out.) - Install printer - Press ‘Exit’ button and select ‘Restart in Window mode’ - Press ‘Start’ then ‘setting’. - Press ‘Add Printer’ - Press ‘Next’ in print installation Wizard - Select ‘Local Printer’ then press ‘Next’. - Choose correct printer driver in the list or use a driver when you purchase a printer. 4.
CDVS-5400 SERIES DVR 4.3 Index Search User can search a recorded image by Index search. User can search a recorded image by sensor, motion, instant recording with this function. - Select Camera : Select camera number. - Select sort option - Sensor : shows image list recorded by sensor - Motion detection : shows image list recorded by motion - Instant Record : shows image list by Instant recording - All event : Shows all list of index recording.
CDVS-5400 SERIES DVR 4.4 Search Backup data User can search a recorded image from a backup media. When user select a backup device, it shows contained data list like a following picture.Choose one of them to playback. - Backup Media : Shows available backup media. -Fixed HDD : Shows installed HDD list in the system. If not selected it shows installed external backup devices. - Choose Start hour : Show the recorded data list from selected device. Press ‘Ok’ button to playback selected image. 4.
CDVS-5400 SERIES DVR 4.6 Thumbnail Preview User can easily find out changed image by this function. This function shows recorded image data by break down in time, 10 minute, every minute. - How to use - Select date from a calendar and select camera. - Press ‘Thumbnail preview’ button.(If camera is not selected, camera 1 is default.) 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 2 3 1 2 3 4 4 5 6 5 6 7 8 9 10 15 16 17 18 19 20 21 22 23 By Time By 10 min. By 1 min.
CDVS-5400 SERIES DVR - Object Search Dialog -Dialog box shows up like a following picture. -Checked Frames : number of compared frames in total. -Time : Time value of the checked frame. -Found : Number of detected frames from key frame. -[Start Search] : It will show you filter dialog and start to find. -[Clear Selection]: clear rectangle selection of object -[Stop] : it will stop searching operation. -[Apply to main search] : load current information to main search mode to do other operation such as zoom.
CDVS-5400 SERIES DVR -Search Filter User can add some search filters to make it easier. -Start Time : It will be automatically loaded from the key frame information. -End Time : End time(10 min. default) it could be the future and the past. -Sensitivity : 1-20 sensitivity option, higher number is more insensitive (default : 3) -Show detected image : It will show all image of the selected region, it make slower to reach.
CDVS-5400 SERIES DVR 5. Setup User can change each setting of camera, resolution, system schedule, communication setup, sensor setup, user management etc. at setup mode. We recommend you don’t allow a permission except Administrator. g) f) a) e) d) b) c) a) Choose camera : Press camera number, then it shows current capturing image with its resolution size. Above picture shows 360x240 resolution. b) Global Setting : User can setup Pan/Tilt receiver type, Auto switching time, Motion Index Interval.
CDVS-5400 SERIES DVR 5.1 Motion Detection User can record image when there happens motion event. As you see in the following picture, you can set 5 motion areas in each camera.(System schedule should be set as motion recording.) Striped areas are motion area - How to set motion area. - Select camera you want to motion recording. - Select area expected motion events - Can set motion area up to 5 regions. - To erase motion area, move the motion box out of screen. - Press ‘Apply’ button.
CDVS-5400 SERIES DVR 5.2 Global Setting In Global setting, you can set overall settings of camera. - Receiver Type : Set type of protocol of Pan/Tilt Camera. Only one protocol is available in a system. - Auto Switching Time(s) : Set auto switching time 1- 100 second. - Motion Index Interval(s) : Set motion recording index interval when you do index search. 5.3 Pan/Tilt Detail Setup To use Pan/Tilt function in camera, you should select connected camera and then check ‘Pan/Tilt Connection’.
CDVS-5400 SERIES DVR 5.4 Recording Schedule User can set the resolution and numbers of recording frame. Following picture shows ‘Recording schedule’ dialog. a) g) b) c) d) e) f) a) Frame Status : Show recording frame status per second. If the box is full, you can’t add more frame in camera. (This is not a display of HDD capacity) b) Camera # Frame : Shows camera number and currently set the number of recorded frame. c) Set Default : Set all the camera’s value as default.
CDVS-5400 SERIES DVR 5.5 System Schedule a) d) b) c) a) Days of Week : Set each day’s schedule of system -Single Selection Mode : Set different schedule everyday. To adjust same schedule in everyday,click ‘Single Selection mode’ then it asks you ‘All day’s information of schedule will change as current state, will you change this?’ . Then press ‘Yes’ button Then everyday checked and button changes to ‘Multi selection Mode’. Now you can see every day's system schedule changes to current state.
CDVS-5400 SERIES DVR c) Special Day Mode This mode enables you set a special day setting(ex : holiday) in a week. User can adjust a different system schedule on a specific date. To change to a special day mode, press ‘Normal day mode’ button. Choose date and set time schedule and then press ‘save special day’ button. Saved day shows in a list box, this schedule will be used on a saved day. -Delete Special Day : Delete saved special day. - Save Special Day : Add special day to a list.
CDVS-5400 SERIES DVR 5.6 Intensive Recording The function Intensive recording uses a different setup for a specific time(for motion,sensor event) of recording. For example, camera ch 1 is set as 10 frame & 360x240 in usual time and intensive recording setup is 720x480, 20 fps. When a sensor & motion is detected, it records as you set in intensive recording. -Holding Duration : Set the recording time for intensive recording.
CDVS-5400 SERIES DVR b) Network Setup -Emergency IP : Type IP address where you want to send image. -Timeout Value : Set timeout value(waiting time) - Center Port : With this port, DVR communicate to Center program. - Image Port : Images are transmitted with this port. - Search Port : This port is used when Center Program communicate searched images with site DVR. - Emergency Port : This port is used for transmitting images to the emergency agent.
CDVS-5400 SERIES DVR e) PPP Setup This is used when you need to send emergency image through public phone line.(Very low speed, we recommend you to use leased line.) - Use PPP : Check whether you use PPP or not. - Password & Confirm : Input password for connecting to PPP network. - Phone Number : Telephone number you will use to connect. - Modem Select : Select modem.(If none installed, it show ‘N/A’) f) Quality & Resolution Choose quality and resolution of image you will send to remote client.
CDVS-5400 SERIES DVR 5.9 Pre-Alarm Recording Records previous image from when sensor & motion detected. Max 1 minute setting is available. If you set 5 seconds, it records images from 5 seconds before when sensor & motion detected. - When index searching, this data marked with ‘P’ letter. And ‘Pre-Alarm’ message shows up. 5.10 Sensor Connection Check sensor you will use with current camera. 5.11 Motion Setting Choose how system warns you when motion detects.
CDVS-5400 SERIES DVR 5.13 Sensor & Output a) b) c) a) Set Sensor -Use : check external sensor 1 ~ 16. - Type : Set type of sensor. To change type just click each buttons. - ‘NO(Normal Open)’ type on usual time. - 'NC(Normal Close)’ when control output. - Record : set number of record frame when sensor detected. - Delay : Set sensor detecting delay time. It works by the second. - Output : Type control output number. If you type 4 on sensor 3, control button 4 will work when sensor 3 detects.
CDVS-5400 SERIES DVR 5.14 Site Information User can find information of current system, site information, drive information etc. at this dialog. b) c) a) d) e) a) Site Information - Site Code : Put site code at here. If this code is not matched with remote client program(center program), you can’t logon from remote site. - Display Sensor Status BAR : Check whether system shows ‘SENSOR’ when sensor detects in display mode.
CDVS-5400 SERIES DVR d) Log Viewer User can check the log by event or system. When you select ‘System log’, you can set the information of your HDD(ex : when the drive changed, formatted..) and if you select ‘Event Log’ you can check all of the login and logout information of this system. System Log Screen Event Log Screen - System Log : Show format & check information of Hard disk drive. - Event Log : Show logon user’s information. - Export : This enables to save current log file to a specific directory.
CDVS-5400 SERIES DVR - Add User : Add users. - Update user : Change users setup. - Delete User : Delete current user’s information - Exit : Close dialog - User Information : shows currently selected user’s information -Permission : Only administrator can give a permission to other users. Administrator can give permissions differently to each user. User can use only checked permission. - Hidden Camera : Administrator can hide some camera to the user.
CDVS-5400 SERIES DVR 6. Center Program(Remote Client program) Center Program is remote client program which enables to control site DVR where communication available. Fixed IP of site DVR is required. Without allowing connection at site DVR, no center user connection available.
CDVS-5400 SERIES DVR 6.1 Installation Center Program 1. Insert enclosed CD title in your PC.(CD-ROM drive must be installed) 2. When program starts, select ‘Software’ and then press ‘Center Software’. 3. Center program will be installed automatically. Click! Install Center program 6.2 Running Center Program 1. Press ‘Start’ button in Window. 2. Select ‘Program’->’DVR’->’Center’->’DVR-Center’. 3. Following picture is initial screen of center program. 4.
CDVS-5400 SERIES DVR 6.3 Add site Information To add new site’s information, press ‘New’ button. -Site Code : Input site DVR code.(must be same with site DVR’s code) -Site Name : Input name of site. - IP Address : Input IP address of site DVR you want to connect. - Center Port : Port number for center communication. - Time out(sec) : Select waiting time for connecting. - Link Type : Set connection type.(TCP/IP, Modem, ISDN) 6.
CDVS-5400 SERIES DVR 6.4 Search in Center program Following screen shows search screen in center program. In center program, you can use functions such as print, file save, afterimage removing, thumbnail preview. Index search, object search is not available in center program.(Except unavailable functions, the usage of other function is same as site DVR’s) 6.5 Setup in Center program Basically, user can change settings of site DVR from a remote place.
CDVS-5400 SERIES DVR 6.6 Sensor & Control setup Configuration of sensor is same as site DVR’s. When you connect sensor, make sure your sensor type. 6.7 Site information In site information, you can add & modify user’s information. Other functions are same as site DVR.
CDVS-5400 SERIES DVR 7. i-DVR program I-DVR is only for surveillance from remote place. Not like center program, you can’t change or do setup, search, pan/tilt control. This program is good for general user who is enrolled at site DVR.
CDVS-5400 SERIES DVR 7.2 Running I-DVR To run I-DVR, press ‘I-DVR Client’ icon on the desktop screen. Following is initial screen of I-DVR. Select cameras you want to see then input user name and password. If everything is ok, press ‘Ok’ and press ‘Go’ button. - Caution : Administrator can’t use I-DVR.. When login system tries to compare user name and password with site DVR’s information. To prevent exposure of Administrator information, this information stored different area.
CDVS-5400 SERIES DVR 8. Emergency Agent - Background Emergency agent is born with a cutting-edge technology to observe many DVRs. This system enables to keep watching many DVRs remotely without wasting local system(Center or PC) resource. 1:1(Center and DVR) connection requires full screen display and higher system resource, but emergency agent only uses minimized resource(less than 3 MB of memory usage) and notify to user with pop-up mechanism when a sensor event occurs from DVRs.
CDVS-5400 SERIES DVR 8.2 How to use 1. Setup a. Run the emergency agent program. b. Click right mouse button on the tray icon ‘ ‘, then press ‘setup’. c. Setup Screen appears like following picture. Choose the messenger option. • Run agent at windows start : Start emergency agent program whenever windows starts • Always on top of the desktop : Emergency agent screen always displays on top of the desktop. • Beep on alarm : ‘Beep’ sound comes out when event occurs.
CDVS-5400 SERIES DVR 8.3 Emergency Agent configuration at site Choose sensor (s) that related to current selected camera. Whenever the selected sensor (s) event happens, the camera start doing predefined actions (recording including intensive recording, pre-alarm, siren, and emergency transmit) It supports multiple connection from sensors to cameras. For example, No. 1 camera can be cooperated with sensor No. 1,2 ,3, and 16, or Sensor No. 1 can be related with camera No. 1,4,5,6, 16.
CDVS-5400 SERIES DVR 8.4 Configuration at remote system (Emergency Agent) Set correct IP address and site code of DVR system. IP address should be crossed between DVR (Site) and Emergency Agent. Set Emergency port with same as site DVR communication configuration. 8.5 Sample screen shot of the Emergency Agent running.
CDVS-5400 SERIES DVR 9. Using Backup Devices. To keep current data for a long time, backup is necessary. User can backup recorded image in Installed hard disk site DVR with using CD-RW, DVD-RAM and IEEE1394 devices. (DAT is not available on Windows2000) - Using CD-RW as backup device. - Check whether CD-RW application program enclosed when you purchase. (ex : direct CD or In-CD) - Press ‘Exit’ button then, select ‘Restart in Windows Mode’. - Install In-CD or Direct CD. - Format CD-RW media.
CDVS-5400 SERIES DVR 10. Make a dial up connection 1. Choose a ‘Network and Dial-up Connections’ at Control Panel 2.
CDVS-5400 SERIES DVR 3. Choose ‘Accept Incoming Connections’ 4. Choose the device you could use in your computer.
CDVS-5400 SERIES DVR 5. Choose ‘Do not allow virtual private connections 6. Add allowed users using ‘Add’ Button. User name must be “dvrsite” - User name must be ‘dvrsite’.
CDVS-5400 SERIES DVR 7. After choose Network component, set the property correctly. 8. Connection Wizard finished. Name the connection you made.
CDVS-5400 SERIES DVR 11. Troubleshooting If you run into any problem using this system, use the following table to troubleshoot the problem. If the problem persists, disconnect the power source and contact nearest service facility. Symptom Cause and/or Corrective Actions System is not work. • Check voltage switch(100V/ 220V) • Check the power is not connected to a outlet No image displays • Check camera cable at BNC panel. • Check whether camera’s power is on.
CDVS-5400 SERIES DVR Symptom Cause and/or Corrective Actions Can’t Backup recorded image • Check if you installed proper application program. • Check backup media.(CD-RW should be formatted before record data.) ‘Permission Denied’ message comes out • Check if you have permission. • Ask your administrator to add more permission. Black screen displays after running S/W • Restart your system • Change video format with using ‘Vformat.
