Datasheet

ManualsBrandsCREE ManualsHighPower-LEDsHighPower LED Cold white 107 lm 90 ° 3.3 V, 3.5 V 350 mA, 700 mA

CLD DS-05 REV12

PRODUCT FAMILY DATA SHEET

Cree

XLamp

XR-E LED

PRODUCT DESCRIPTION

The XLamp XR-E LED is leading the

LED lighting revolution with its un-

precedented lighting-class bright-

ness, efcacy, lifetime and quality

of light. These lighting-class fea-

tures enable the XLamp XR-E LED

to replace many traditional light

sources and save money with ener-

gy-efcient light and long lifetimes.

Cree XLamp LEDs bring high per-

formance and quality of light to a

wide range of lighting applications,

including color-changing lighting,

portable and personal lighting,

outdoor lighting, indoor directional

lighting, commercial lighting and

emergency-vehicle lighting.

FEATURES

• Guaranteed minimum ux

order codes up to 114 lm in

white, 30.6 lm in blue and

67.2 lm in green at 350 mA

• Available in white (2,600 K

to 10,000 K CCT), blue,

royal blue and green

• Maximum drive current: up

to 1000 mA

• Industry’s lowest thermal

resistance: 8°C/W

• Max junction temperature:

150°C

• Industry-leading JEDEC

standard pre-qualication

testing

• Reow solderable – JEDEC J-

STD-020C compatible

• Electrically neutral thermal

path

• RoHS-compliant

• Lumen maintenance of

greater than 70% after

50,000 hours

TABLE OF CONTENTS

Flux Characteristics (TJ = 25°C) -

White ....................................2

Flux Characteristics (TJ = 25°C) -

Color .....................................3

Characteristics ..........................4

Relative Spectral Power Distribution . 5

Relative Flux vs. Junction Temperature

(IF = 350 mA) ..........................6

Electrical Characteristics

(TJ = 25˚C) .............................7

Thermal Design.........................7

Relative Flux vs. Current

(TJ = 25˚C) .............................8

Typical Spatial Distribution ............ 8

Reow Soldering Characteristics ......9

Notes .................................. 10

Mechanical Dimensions

= 25°C) ........................... 11

Tape and Reel......................... 12

Dry Packaging and Packaging ....... 13

WWW. CREE.COM/XLAMP

notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc.

Cree, Inc.

4600 Silicon Drive

Durham, NC 27703

USA Tel: +1.919.313.5300

Summary of content (28 pages)

PAGE 1
CLD DS-05 REV12 PRODUCT FAMILY DATA SHEET Cree XLamp XR-E LED ® ® PRODUCT DESCRIPTION The XLamp XR-E LED is leading the FEATURES • LED lighting revolution with its unprecedented lighting-class brightness, efficacy, lifetime and quality of light. These lighting-class fea- • tures enable the XLamp XR-E LED to replace many traditional light sources and save money with energy-efficient light and long lifetimes.
PAGE 2
XLAMP XR-E LEDS FLUX CHARACTERISTICS (TJ = 25°C) - WHITE The following tables describe the available colors and flux for XR-E LEDs by listing the correlated color temperature or dominant wavelength range for the entire family and by providing several base order codes. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family.
PAGE 3
XLAMP XR-E LEDS FLUX CHARACTERISTICS (TJ = 25°C) - COLOR The following tables describe the available colors and flux for XR-E LEDs by listing the correlated color temperature or dominant wavelength range for the entire family and by providing several base order codes. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family.
PAGE 4
XLAMP XR-E LEDS CHARACTERISTICS Characteristics Unit Thermal Resistance, junction to solder point °C/W 8 Viewing Angle (FWHM) - white degrees 90 Viewing Angle (FWHM) - royal blue, blue, green degrees 100 Temperature coefficient of voltage - white, royal blue, blue, green Minimum mV/°C ESD Classification (HBM per Mil-Std-883D) Typical Maximum -4.
PAGE 5
XLAMP XR-E LEDS Relative Spectral Power RELATIVE SPECTRAL POWER DISTRIBUTION Relative Radiant Power (%) 100 80 60 5000K - 10000K CCT 3700K - 5000K CCT 2600K - 3700K CCT 40 20 0 400 450 500 550 600 CLD DS-05.011 650 700 750 Wavelength (nm) Relative Radiant Power (%) 100 80 60 Royal Blue Blue Green 40 20 0 400 450 500 550 600 650 Wavelength (nm) Relative Flux Output vs. Junction Temperature (If = 350 mA) Copyright © 2006-2011 Cree, Inc. All rights reserved.
PAGE 6
XLAMP XR-E LEDS RELATIVE FLUX VS. JUNCTION TEMPERATURE (IF = 350 MA) 100% Relative Luminous Flux 90% 80% 70% 60% 50% 40% 30% 20% CLD DS-05.011 10% 0% 25 50 75 100 Junction Temperature (°C) 125 150 100% 90% Relative Radiant Flux 80% 70% 60% 50% 40% Royal 30% Electrical Characteristics (Tj = 25ºC) 20% 10% 0% 25 50 75 100 125 150 Junction Temperature (ºC) Copyright © 2006-2011 Cree, Inc. All rights reserved. The information in this document is subject to change without notice.
PAGE 7
XLAMP XR-E LEDS ELECTRICAL CHARACTERISTICS (TJ = 25˚C) 1000 900 Forward Current (mA) 800 700 600 500 400 Thermal Design 300 200 CLD DS-05.011 100 0 0.0 1.0 2.0 3.0 4.0 5.
PAGE 8
Relative Intensity vs. Current (Tj = 25ºC) 100 0 0 25 50 75 100 125 150 XLAMP XR-E LEDS Ambient Temperature (°C) RELATIVE FLUX VS. CURRENT (TJ = 25˚C) Relative Luminous Flux (%) 250 200 150 100 50 Typical Spatial RadiationCLD Pattern DS-05.011 0 0 200 400 600 800 1000 Forward Current (mA) TYPICAL SPATIAL DISTRIBUTION Relative Luminous Intensity (%) 120 100 80 White 60 Color 40 20 0 -100 -80 -60 -40 -20 0 20 40 60 80 100 Angle (°) Copyright © 2006-2011 Cree, Inc.
PAGE 9
XLAMP XR-E LEDS REFLOW SOLDERING CHARACTERISTICS In testing, Cree has found XLamp XR-E LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. CLD DS-05.
PAGE 10
XLAMP XR-E LEDS NOTES Lumen Maintenance Projections Baking Conditions Based on internal long-term reliability testing, Cree projects that white XLamp XR-E LEDs will deliver median 70% lumen maintenance after 50,000 hours of operation at a forward current of 700 mA. This projection is based on constant current operation with junction temperature maintained at or below 135°C and ambient air temperature maintained at or below 25°C. It is not necessary to bake all XLamp LEDs.
PAGE 11
XLAMP XR-E LEDS MECHANICAL DIMENSIONS (TA = 25°C) All measurements are ±.1mm unless otherwise indicated. Lens Substrate Reflector Reflector Lens Substrate 6.8 mm CLD DS-05.011 4.4 ± .2 mm Side View 9.0 mm 8.4 mm 5.6 mm 6.46 mm 0.7 mm 7.0 mm Bottom View Top View 8.4 mm 7.0 mm 5.6 mm 0.70 mm 6.46 mm Recommended PC Board Solder PadPC Board Solder Pad Recommended Copyright © 2006-2011 Cree, Inc. All rights reserved. The information in this document is subject to change without notice.
PAGE 12
XLAMP XR-E LEDS TAPE AND REEL All dimensions in mm. CLD DS-05.011 + 330.2 mm Copyright © 2006-2011 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc.
PAGE 13
XLAMP XR-E LEDS Humidity Indicator DRY PACKAGING AND PACKAGING Card (inside bag) Humidity Indicator Card (inside bag) Label with Cree Bin Code, Qty, Lot # Label with Cree Bin Code, Qty, Lot # Dessicant (inside bag) Dessicant (inside bag) CLD DS-05.011 Vacuum-Sealed Moisture Barrier Bag Vacuum-Sealed Moisture Barrier Bag Label with Cree Bin Code, Qty, Lot # Label with Cree Bin Code, Qty, Lot # with Customer Label with Label Customer Order Order Code, Code, Qty, Qty, ReelReel ID, ID, POP.O.
PAGE 14
CLD AP12 REV 8 BINNING & LABELING Cree XLamp XR-E and XR-C LED ® ® INTRODUCTION TABLE OF CONTENTS This document describes the product nomenclature Bin and Order-Code Format................................. 3 required to select and order Cree’s XLamp XR-E and Performance Groups – Brightness......................... 4 XR-C LEDs. XLamp XR-E and XR-C LEDs are tested and Performance Groups – Chromaticity......................
PAGE 15
CLD AP12 REV 8 BIN AND ORDER-CODE FORMAT Bin codes and order codes are configured in the following manner: Order Code Bin Code Series XRE = XR-E XRC = XR-C Series XRE = XR-E XRC = XR-C Optical configuration (default = L1) Optical configuration (default = L1) Kit number Luminous or radiant flux group SSSCCC-BD-HHHH-NNNNN Internal code Internal code Color WHT = White ROY = Royal Blue BLU = Blue GRN = Green AMB = Amber RDO = Red-Orange RED = Red SSSCCC-BD-WW-FF-G-AA Forward voltage group (amber, red
PAGE 16
CLD AP12 REV 8 PERFORMANCE GROUPS – BRIGHTNESS White XLamp XR-E and XR-C LEDs are tested for luminous flux and placed into one of the following luminous-flux groups: Group Code Min. Luminous Flux @ 350 mA (lm) Max. Luminous Flux @ 350 mA (lm) M2 39.8 45.7 M3 45.7 51.7 N2 51.7 56.8 N3 56.8 62.0 N4 62.0 67.2 P2 67.2 73.9 P3 73.9 80.6 P4 80.6 87.4 Q2 87.4 93.9 Q3 93.
PAGE 17
CLD AP12 REV 8 PERFORMANCE GROUPS – BRIGHTNESS (CONTINUED) Royal-blue XLamp XR-E and XR-C LEDs are tested for radiant flux and placed into one of the following radiant-flux groups: Group Min. Radiant Flux (mW) @ 350 mA Max. Radiant Flux (mW) @ 350 mA 12 250 300 13 300 350 14 350 425 15 425 500 16 500 600 PERFORMANCE GROUPS – CHROMATICITY White XLamp LEDs are tested for chromaticity and placed into one of the regions defined by the bounding coordinates below.
PAGE 18
CLD AP12 REV 8 PERFORMANCE GROUPS – CHROMATICITY (CONTINUED) Region 3A 4A 5A 6A 7A 8A x y .3371 .3451 .3440 .3428 .3366 .3369 .3512 .3465 .3529 .3597 .3615 .3659 .3590 Region x y .3490 .3376 .3554 .3463 .3451 .3554 .3371 .3490 .3529 .3597 .3548 .3736 .3641 .3804 .3521 .3615 .3670 .3578 .3702 .3722 .3825 .3798 .3783 .3646 .3889 .3690 .3941 .3848 .4080 .3916 .4017 Region x y .3616 .3463 .3687 .3551 .3533 .3620 .3451 .3554 .3615 .3659 .3641 .
PAGE 19
CLD AP12 REV 8 PERFORMANCE GROUPS – DOMINANT WAVELENGTH Color XLamp LEDs are tested for dominant wavelength (DWL) and placed into one of the DWL groups defined below. Color DWL Group Min. DWL (nm) @ 350 mA Max.
PAGE 20
CLD AP12 REV 8 CREE’S STANDARD CHROMATICITY REGIONS PLOTTED ON THE 1931 CIE CURVE                                                                                  
PAGE 21
CLD AP12 REV 8 STANDARD ORDER CODES AND BINS (XR-C COOL WHITE) The following tables list standard kit numbers and performance bins. Kit numbers completely describe an order code’s chromaticity regions and luminous flux range. XLamp XR-C LED Standard Order Codes - White Min. Luminous Flux (lm) @ 350 mA* Group Chromaticity Regions Kit Number Flux (lm) Cool White (5000 K – 10,000 K) N3 N4 P2 P3 P4 Q2 56.8 62.0 67.2 73.9 80.6 87.
PAGE 22
CLD AP12 REV 8 STANDARD ORDER CODES AND BINS (XR-C NEUTRAL WHITE) The following tables list standard kit numbers and performance bins. Kit numbers completely describe an order code’s chromaticity regions and luminous flux range. XLamp XR-C LED Standard Order Codes - White Min Luminous Flux (lm) @ 350 mA* Group Chromaticity Regions Kit Number CCT 4C, 4D, 5A, 5B 004F5 4300 K 5A, 5B, 5C, 5D 004E5 4000 K Flux (lm) Neutral White (3700 K – 5000 K) N2 N3 N4 P2 P3 P4 51.7 56.8 62.0 67.2 73.
PAGE 23
CLD AP12 REV 8 STANDARD ORDER CODES AND BINS (XR-C WARM WHITE) The following tables list standard kit numbers and performance bins. Kit numbers completely describe an order code’s chromaticity regions and luminous flux range. XLamp XR-C LED Standard Order Codes - White Min Luminous Flux (lm) @ 350 mA* Group Flux (lm) M2 39.
PAGE 24
CLD AP12 REV 8 STANDARD ORDER CODES AND BINS (XR-C COLOR) The following tables list standard kit numbers and performance bins. Kit numbers completely describe an order code’s dominant-wavelength range and luminous- or radiant-flux range. XLamp XR-C LED Standard Order Codes - Royal Blue Color Dominant Wavelength (nm) Min. Radiant Flux (mW) @ 350 mA* Group Flux (mW) 12 250 Royal Blue 13 300 Min. Max.
PAGE 25
CLD AP12 REV 8 STANDARD ORDER CODES AND BINS (XR-E COOL WHITE) The following tables list standard kit numbers and performance bins. Kit numbers completely describe an order code’s chromaticity regions and luminous flux range. XLamp XR-E LED Standard Order Codes - White Min. Luminous Flux (lm) @ 350 mA* Group Chromaticity Regions Kit Number Flux (lm) Cool White (5000 K – 10,000 K) P4 Q2 Q3 Q4 Q5 80.6 87.4 93.
PAGE 26
CLD AP12 REV 8 STANDARD ORDER CODES AND BINS (XR-E NEUTRAL WHITE) The following tables list standard kit numbers and performance bins. Kit numbers completely describe an order code’s chromaticity regions and luminous flux range.
PAGE 27
CLD AP12 REV 8 STANDARD ORDER CODES AND BINS (XR-E WARM WHITE) The following tables list standard kit numbers and performance bins. Kit numbers completely describe an order code’s chromaticity regions and luminous flux range. XLamp XR-E LED Standard Order Codes - White Minimum Luminous Flux (lm) @ 350 mA* Group Chromaticity Regions Kit Number CCT 6C, 6D, 7A, 7B 005F7 3200 K 7A, 7B, 7C, 7D 005E7 3000 K Flux (lm) Warm White (2600 K - 3700 K) N3 N4 P2 P3 P4 Q2 56.8 62.0 67.2 73.9 80.
PAGE 28
CLD AP12 REV 8 STANDARD ORDER CODES AND BINS (XR-E COLOR) The following tables list standard kit numbers and performance bins. Kit numbers completely describe an order code’s dominant-wavelength range and luminous- or radiant-flux range. XLamp XR-E LED Standard Order Codes - Royal Blue Color Royal Blue Dominant Wavelength (nm) Min. Radiant Flux (mW) @ 350 mA* Group Flux (mW) 13 300 14 15 350 425 Min. Max.