Datasheet

Copyright © 2010-2014 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree
®
, the Cree logo and XLamp
®
are registered
trademarks of Cree, Inc. ENERGY STAR
®
is a registered trademark of the U.S. Environmental Protection Agency.
13
xlamp
®
xp-e high-efficiency white leds
13
TAPE AND REEL
All Cree carrier tapes conform to EIA-481D, Automated Component Handling Systems Standard.
All dimensions in mm.
Loaded Pockets
(1,000 Lamps)
Leader
400mm (min) of
empty pockets with
at least 100mm
sealed by tape
(50 empty pockets min.)
Trailer
160mm (min) of
empty pockets
sealed with tape
(20 pockets min.)
START END
Cathode Side
Anode Side
(denoted by + and circle)
160.0
A
A
B
2.5 ±.1
SECTION A-A
SCALE 2 : 1
1.5 ±.1
8.0 ±.1
4.0 ±.1
1.75 ±.10
12.0
.0
+ .3
DETAIL B
SCALE 2 : 1
13 mm
7"
Cover Tape
Pocket Tape
User Feed Direction
User Feed Direction
Y
Y
X
X
REF 0.59
W
F(III)
P1
D1
1.5 MIN.
Bo
Ao
R0.2
TYPICAL
REF
4.375
Ko
Other material available.(IV)
(III)
(II)
(I)
hole to centerline of pocket.
Measured from centerline of sprocket
holes is ± 0.20.
Cumulative tolerance of 10 sprocket
to centerline of pocket.
Measured from centerline of sprocket hole
SECTION Y-Y
SECTION X-X
2.0 ±0.05 (I)
P2
1.55 ±0.05
Do
4.0 ±0.1 (II)
Po
1.75 ±0.1 E1
0.30 ±0.05
T
REF R
2.24
2.40Ko +0.0/-0.1
3.70
1
W
F
P
+/- 0.05
+/- 0.1
+0.3/-0.1
5.50
8.00
12.00
Ao 3.70 +/- 0.1
Bo +/- 0.1
Y
Y
X
X
REF 0.59
W
F(III)
P1
D1
1.5 MIN.
Bo
Ao
R0.2
TYPICAL
REF
4.375
Ko
Other material available.(IV)
(III)
(II)
(I)
hole to centerline of pocket.
Measured from centerline of sprocket
holes is ± 0.20.
Cumulative tolerance of 10 sprocket
to centerline of pocket.
Measured from centerline of sprocket hole
SECTION Y-Y
SECTION X-X
2.0 ±0.05 (I)
P2
1.55 ±0.05
Do
4.0 ±0.1 (II)
Po
1.75 ±0.1 E1
0.30 ±0.05
T
REF R
2.24
2.40Ko +0.0/-0.1
3.70
1
W
F
P
+/- 0.05
+/- 0.1
+0.3/-0.1
5.50
8.00
12.00
Ao 3.70 +/- 0.1
Bo +/- 0.1
Y
Y
X
X
REF 0.59
W
F(III)
P1
D1
1.5 MIN.
Bo
Ao
R0.2
TYPICAL
REF
4.375
Ko
Other material available.(IV)
(III)
(II)
(I)
hole to centerline of pocket.
Measured from centerline of sprocket
holes is ± 0.20.
Cumulative tolerance of 10 sprocket
to centerline of pocket.
Measured from centerline of sprocket hole
SECTION Y-Y
SECTION X-X
2.0 ±0.05 (I)
P2
1.55 ±0.05
Do
4.0 ±0.1 (II)
Po
1.75 ±0.1 E1
0.30 ±0.05
T
REF R
2.24
2.40Ko +0.0/-0.1
3.70
1
W
F
P
+/- 0.05
+/- 0.1
+0.3/-0.1
5.50
8.00
12.00
Ao 3.70 +/- 0.1
Bo +/- 0.1

