Instruction Manual

ManualsBrandsCREE LIGHTING ManualsOtherCREE LIGHTING Vuepoint Series LED Luminaire Hook and Cord or Pendant Mount

Vuepoint Series

LED Luminaire

Hook and Cord or Pendant Mount

1 of 5

LPN00848X0001A0_B

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should

always be followed including the following:

READ AND FOLLOW ALL

SAFETY INSTRUCTIONS

1. DANGER- Risk of shock- Disconnect power before installation.

DANGER – Risque de choc – Couper l’alimentation avant

l’installation.

2. This luminaire must be installed in accordance with the NEC or

your local electrical code. If you are not familiar with these codes

and requirements, consult a qualied electrician.

Ce produit doit être installé conformément à NEC ou votre code

électrique local. Si vous n’êtes pas familier avec ces codes et ces

exigences, veuillez contacter un électricien qualié.

3. Suitable for damp location.

Convient aux emplacements humides.

4. MIN 90°C SUPPLY CONDUCTORS

LES FILS D’ALIMENTATION 90°C MIN.

5. Check to make sure that all input power connections have been

properly made and the luminaire is grounded to avoid potential

electrical shock.

6. DO NOT lift luminaire by the power cord or any of the cables

connected to the LED heatsink and LED driver.

SAVE THESE INSTRUCTIONS

FOR FUTURE REFERENCE

NOTES:

• Images used in this installation sheet are for illustration purpose,

there are different congurations of the luminaire.

• For each mounting application below, when mounting to surface

ensure that the mounting surface and customer supplied

hardware is capable of supporting the weight of the luminaire.

• The center of mounting is NOT the same as the center of

luminaire.

TO INSTALL:

HOOK AND CORD MOUNT

STEP 1:

Loosen the long screw from the hook. See Figure 1.

STEP 2:

Slide hook into securely mounted customer supplied eye hanger

and tighten the long screw from Step 1.

NOTE: The luminaire should already be factory set for correct

balance. If necessary, the fixture may be balanced by loosening

the hook adjustment screws on the top of housing and sliding the

hook as necessary for correct balance. Tighten hook adjustment

screws when finished.. See Figure 1.

STEP 3:

Attach luminaire cord to customer supplied junction box

and strain relief. Make wiring connections per the Electrical

Connections section.

Adjustable Hook Bracket

Hook

Screw

Fixed bracket

Vuepoint

Summary of content (5 pages)

PAGE 1
Vuepoint Series LED Luminaire Hook and Cord or Pendant Mount INSTALLATION INSTRUCTIONS INSTRUCTIONS D’INSTALLATION IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. DANGER- Risk of shock- Disconnect power before installation. DANGER – Risque de choc – Couper l’alimentation avant l’installation.
PAGE 2
PENDANT MOUNTING 2 Phillips Head Screw STEP 1: Remove the hook from the adjustable hook bracket by loosening the Philips head screw on the adjustable hook bracket locknut. See Figure 2. STEP 2: Insert customer supplied ½” IPS stem into adjustable hook bracket locknut and tighten Philips head screw to lock. STEP 3: Secure Pendant to structure or junction box using customer supplied locknuts.
PAGE 3
ELECTRICAL CONNECTIONS STEP 1: LUMINAIRE Make the following Electrical Connections: b. For 120/277V connect the white fixture lead to the neutral supply or Hot 2 (for 208/240V wiring). c. Connect the green or green/yellow ground lead to the green wire position of the terminal block. STEP 2: d. If 0/1-10V dimming is used connect the violet lead to the supply positive dimming lead. e.
PAGE 4
8 9 Distance may vary depending on the lighting environment max. height of 40' 10 11 FSP-2X1 COMMISSIONING BATTERIES The commissioning process establishes the appropriate operating parameters of the FSP-2X1. This is done using the programming tool. The programming tool operates on three standard 1.5V AAA Alkaline batteries or three rechargeable AAA NiMH batteries (See Figure 10). The battery status is shown in the upper right corner of the home screen (See Figure 11).
PAGE 5
TROUBLESHOOTING NO RESPONSE SCREEN APPEARS: • Make sure that the sensor is not obstructed. • Move closer to the sensor. A ladder or lift may be required. • The angle may be too high, move closer so that you are directly underneath the sensor. • Make sure that multiple sensors are not in the range of the transceiver. If this happens, then all of the luminaires will cycle. • If still not successful, there may be too much IR interference from other sources.