Instruction Manual

LPN00838X0002A0_A
1 of 3
Cree Wireless Scene Controller With
SmartCast
®
Technology
Wireless Scene Controller
Includes: CSC-SC-XX
INSTALLATION INSTRUCTIONS
INSTRUCTIONS D’INSTALLATION
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should
always be followed including the following:
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS
1. Before installing Wireless Scene Controller turn off the power at
the circuit breaker.
Couper l’alimentation avant l’installation
2. These Wireless Scene Controller must be installed in accordance
with the national and local building codes and electrical wiring
codes including wiring methods and wiring connections. If you
are not familiar with these codes and requirements, consult a
Ce produit doit être installé conformément à NEC ou votre code
électrique local. Si vous n’êtes pas familier avec ces codes et ces
3. Indoor use only and suitable for damp locations.
Pour usage interieur seulement et convient aux emplacements
humides.
4.
equipment.
SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE
UNIT DESCRIPTION
The Cree Wireless Scene Controller is used with other SmartCast
®
Technology enabled devices to provide wireless preset/scene control of SmartCast-
enabled LED luminaires. The Cree Wireless Scene Controller provides default and customizable scene controls for up to 14 control zones.
LOAD TYPES
Cree Wireless Scene Controller support Cree SmartCast
®
Technology enabled devices only.
• Voltage: 120-277V, 60Hz
• Depth in Wall: 1.5"
• For ease of installation, Cree recommends the use of a deep wall
• NOT FOR USE WITH METALLIC FACEPLATES.
LPN00838X0002A0_A
2 of 3
WIRELESS SCENE CONTROLLER
FEATURES
• The Cree Scene Controller supports on,
off, and dimming controls. See Figure
1.
• The Cree Wireless Scene Controller
supports on, off, and dimming, and
color controls. See Figure 1.
• The Cree Wireless Scene Controller
provides preset scene control from a
single-gang push-button wallstation.
• Scenes may be assigned to each of the
5 buttons. See Figure 1.
• Preset scenes may assign light levels,
color temperatures (CCT), or both.
INSTALLATION
NOTE: For ease of installation, Cree
recommends using a deep wall box.
STEP 1:
Disconnect power to circuit by turning circuit
breaker OFF before installation.
STEP 2:
If necessary remove existing wall plate and
switch.
STEP 3:
Strip existing wires ½". If two wires will be
connected to the same terminal on the Cree
device, both wires must be the same gauge
(12AWG or 14AWG).
STEP 4:
Wire the LINE (black), NEUTRAL (white),
and GND (green or bare) supply wires to
the corresponding pigtail leads on the Cree
device, as shown in Figure 2.
For Scene controllers with no neutral wire.
Wire the LINE IN (black) to supply wires, LINE
OUT to the switched power, and GND (green
or bare) supply wires to the corresponding
pigtails on the Cree device, as shown in
Figure 3.
NOTE: If replacing an existing wall switch, the
Wireless Scene Controller shall be wired as
instructed; however, the switched power to
the load must also be tied directly to the AC
supply leads.
STEP 5:
Attach the wall plate (reference the wall plate
instruction sheet).
STEP 6:
Switch the circuit breaker ON.
STEP 7:
Press and release any button. The blue LED
should blink twice and then go off. If the
blue LED does not respond with the two-
blink sequence, please follow the RESET
instructions to return the Wireless Scene
Controller to factory defaults.
NEUT
GND
LINE
SUPPLY
LEADS
2
LED
LINE
GND
LINE IN
SUPPLY
LEADS
3
LINE TO
LOAD
120-277VAC
60Hz XX
APPLIANCE
CONTROLS
18AWG Cu wire
Made
in China
TOP
CSC-SC
5NW1
Status
LED
1
Button 2
Button 3
Top
Button/
Button 1
Button 4
Button 5
WIRELESS SCENE
CONTROLLER
120-277VAC
60Hz XX
APPLIANCE
CONTROLS
18AWG Cu wire
Made
in China
TOP
CSC-SC
5NW1
• Type 1 enclosure & IP20 Indoor use
• Operating Temperature limit of the control: 0 to 35C
• Software Class A Lighting Controls
• Pollution degree 2 Suitable for normal household air circulation
•
Operating Control, Electronic Dimming Switch;•