Installation Instructions

LPN00838X0001A0_A
1 of 3
Cree Wireless Wall Controls With
SmartCast
®
Technology
Wireless Dimmer and Wireless Switch
Includes:CSC-CWD, CSC-CWS, CSC-CCD
INSTALLATION INSTRUCTIONS
INSTRUCTIONS D’INSTALLATION
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should
always be followed including the following:
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS
1. Before installing wall controls turn off the power at the circuit
breaker.
Couper l’alimentation avant l’installation
2. These wall controls must be installed in accordance with the
national and local building codes and electrical wiring codes
including wiring methods and wiring connections. If you are not
electrician.
Ce produit doit être installé conformément à NEC ou votre code
électrique local. Si vous n’êtes pas familier avec ces codes et ces
3. Indoor use only and suitable for damp locations.
Pour usage interieur seulement et convient aux emplacements
humides.
4.
equipment.
SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE
120-277VAC
60Hz XX
APPLIANCE
CONTROLS
18AWG Cu wire
Made
in China
TOP
CSC-CCD
5NW1
120-277VAC
60Hz XX
APPLIANCE
CONTROLS
18AWG Cu wire
Made
in China
TOP
CSC-CWS
5NW1
WIRELESS SWITCH
CWS-CWC
WIRELESS DIMMER
CSC-CWD, CSC-CCD
UNIT DESCRIPTION
The Cree Wireless Wall Controls are used with other SmartCast
®
Technology enabled devices to provide wireless control of LED luminaires. The Cree
Wireless Wall Controls provide on, off, dimming control, and color adjustment.
LOAD TYPES
Cree Wall Controls support Cree SmartCast
®
Technology enabled devices only.
• Voltage: 120-277V, 60Hz
• Depth in Wall: 1.5"
• For ease of installation, Cree recommends the use of a deep wall
• NOT FOR USE WITH METALLIC FACEPLATES.
• Type 1 enclosure & IP20 Indoor use
• Operating Temperature limit of the control: 0 to 35C
• Software Class A Lighting Controls
• Pollution degree 2 Suitable for normal household air circulation
•
LPN00838X0001A0_A
2 of 3
WALL CONTROLS FEATURES
• The Cree Wireless Dimmer supports on,
off, and dimming controls. See Figure 1.
• The Cree Wireless CCT Dimmer supports
on, off, and dimming, and color controls.
Color is adjusted up by simultaneously
pressing the On and Dimming up
buttons. Color is adjusted down by
simultaneously pressing the Off and
Dimming down buttons. See Figure 1.
• The Cree Wireless Switch supports on
and off, controls. See Figure 2.
INSTALLATION
NOTE: For ease of installation, Cree
recommends using a deep wall box.
STEP 1:
Disconnect power to circuit by turning circuit
breaker OFF before installation.
STEP 2:
If necessary remove existing wall plate and
switch.
STEP 3:
Strip existing wires ½". If two wires will be
connected to the same terminal on the Cree
device, both wires must be the same gauge
(12AWG or 14AWG).
STEP 4:
Wire the LINE (black), NEUTRAL (white),
and GND (green or bare) supply wires to the
corresponding pigtail leads on the Cree device,
as shown in Figure 3.
For wireless dimmers with no neutral wire.
Wire the LINE IN (black) to supply wires, LINE
OUT to the switched power, and GND (green or
bare) supply wires to the corresponding pigtails
on the Cree device, as shown in Figure 4.
NOTE: If replacing an existing wall switch
with a wireless dimmer with neutral wire
connection, the wall dimmer shall be wired as
instructed; however, the switched power to the
load must also be tied directly to the AC supply
leads.
STEP 5:
Attach the wall plate (reference the wall plate
instruction sheet).
STEP 6:
Switch the circuit breaker ON.
STEP 7:
Press and release the OFF paddle. The blue
LED should blink twice and then go off. If the
blue LED does not respond with the two-blink
sequence, please follow the RESET instructions
to return the wall control to factory defaults.
NEUT
GND
LINE
SUPPLY
LEADS
3
120-277VAC
60Hz XX
APPLIANCE
CONTROLS
18AWG Cu wire
Made
in China
TOP
CSC-CCD
5NW1
On
Dimming
Up
LED
Off
Dimming
Down
2
1
120-277VAC
60Hz XX
APPLIANCE
CONTROLS
18AWG Cu wire
Made
in China
TOP
CSC-CWS
5NW1
On
LED
Off
LINE
GND
LINE IN
SUPPLY
LEADS
4
LINE TO
LOAD