Safety Instructions

3
of3
LPN00838X0004A0_A
SCENE CONTROLLER PAIRING INSTRUCTIONS
STEP 1:
Down the free App (Search for Cree Lighting).
STEP 2:
Press&Hold(approx.5sec)buttons1, 3,and5atthesametime
until the LED flashes fast, means switch is ready for pairing.
STEP 3:
Auto-Scan APP Pairing Method:
• Pair
• Followon-screenstepsintheapptoconnectto
your scene controller
• Enable Bluetooth on your device
• Guided Setup
• Follow step-by-step on-screen instructions to configure
each button
STEP 4:
Build Scenedefinitionin App
, theusercanaddpersonal settings
toalightorgroupoflightsbyselecting CCTlevel, Color,orpreset
Scene to a button which will synchronize with the controller. Follow
step-by-stepon-screeninstructionstoconfigureeachbutton
Resetcontroller,
Press& Hold(approx.5 sec) Scene1buttonuntil
the LED flashes fast, means Switch reset is finished.
CLEANING
Clean using a cloth dampened only with water and a little mild
detergent. Use of solvents or hydrocarbon-based cleaners may
cause permanentdamage.
FCC NOTICE
Thisdevicecomplieswithpart 15 of the FCC Rules. Operationis
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
AnyChangesormodificationsnotexpresslyapprovedbytheparty
responsible for compliance could void the user's authority to
operate the equipment.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules.These limitsare designed to providereasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
causeharmful interferenceto radioortelevision reception, which
canbe determined by turningthe equipment off and on, the useris
encouraged to try to correct the interference by one or more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connecttheequipmentintoanoutleton acircuitdifferentfrom
that to which the receiver is connected.
-Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between
the radiator & your body.
Inaddition,thisdevicecomplieswithICES-003ofthe Industry
Canada (IC) Regulations.
INDUSTRY CANADA STATEMENT
This device complies with Industry Canada licence-exempt RSS
standard(s).Operationissubjecttothefollowingtwoconditions:(1)
this device may not cause interference, and (2) this device must accept
anyinterference,includinginterferencethatmaycauseundesired
operationofthedevice. Inaddition,thisdevicecomplieswith ICES-003
of the Industry Canada (IC) Regulations.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autoriséeauxdeuxconditionssuivantes:(1)l’appareilnedoitpas
produiredebrouillage, et (2) l’utilisateur del’appareil doitaccepter
tout brouillage radioélectrique subi, même si le brouillage est
susceptibled’en compromettre le fonctionnement.
This equipment complies with RSS-102 radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between
the radiator & your body.
Wall Control Troubleshooting
Issue
Resolution
Wireless Scene Controller LED
does not blink
Check wiring
(LINE/NEUT/GND required)
Resetthecontrollerandverifythe LEDflashes
fast continuously.
Wireless Scene Controller will
not join a network
Check wiring (LINE/NEUT/GND required).
Resetthecontrollerandverifythe LEDflashes
fast continuously.
Replaced existing Wireless
Scene Controller and fixtures
will not turn on
CheckWiring(eachfixtureshallbewiredwith
constant HOT)
Wireless Scene Controller will
not control fixtures
Check group assignments with Configuration
Tool