CREDA FLORIDA PLUS ELECTRIC SHOWER Installation and User Guide IMPORTANT: This booklet should be left with the user after installation and demonstration
CONTENTS Section Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . How to install your Florida Plus Shower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . How to maintain your Florida Plus Shower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HOW TO INSTALL YOUR FLORIDA PLUS SHOWER WARNING: ALL WIRING AND INSTALLATION MUST BE SUPERVISED BY A SUITABLY QUALIFIED PERSON. WARNING: DO NOT INSTALL THIS SHOWER WHERE IT MAY BE SUBJECTED TO FREEZING CONDITIONS We recommend that the installation is done in the following sequence. a. Fixing the shower to the wall b. Plumbing c. Electrical connections a. FIXING THE SHOWER TO THE WALL 1. Position the riser rail at a convenient height for majority of users as detailed in Diagram 1 and mark its position. 2.
7. If you have not yet done so, remove the front cover assembly by undoing the retaining screws at the top and bottom of the unit and lifting the cover off. Your shower is provided with 2 fixing positions in the backplate (see Diagram 7 on page 9). The top-fixing hole is a “key-hole” slot (another key-hole is provided for alternate fixing), and should be marked and drilled first. Tighten top screw with head protruding about 10mm from the wall and hook the backplate over the screw head.
7. The shower is designed to have an open outlet and should only be used with “Creda” recommended fittings. Do not connect the handset until after the shower front cover and corner section are fitted. WARNING: DO NOT FIT A TAP ON THE SHOWER OUTLET. WARNING: TAKE CARE TO AVOID RESTRICTING THE OUTLET OF THE PRESSURE RELIEF DEVICE. c) ELECTRICAL WARNING: THIS SHOWER MUST BE EARTHED. The electrical installation must be in accordance with the current BS.
4. Ensure the corner section is fitted back into the backplate. 5. Re-fit the front cover back into position making sure the knobs are aligned correctly with the flow valve and power selector (see Diagram 5). Start by locating the “tang” around the recess for the outlet pipe, and then “roll” the front cover over the knobs and onto the top of the backplate. Replace and secure the top and bottom fastening screws. Diagram 5 Diagram 4 Schematic Wiring Diagram 6.
HOW TO USE YOUR FLORIDA PLUS SHOWER (DETAILED) 1. Ensure the electricity and water are turned on to the unit. Diagram 6 2. Your shower has 3 power settings selected by turning knob “A” (see Diagram 6). The most popular is “FULL HEAT” indicated by “ ” and for your convenience this can be obtained in two positions so you are always only one step away from maximum power. There are also options for a “HALF HEAT ” or “COLD ” shower (see notes 8 and 9).
WHAT TO DO IF THINGS GO WRONG (1) SELF HELP If the shower is not working satisfactorily, make the following checks before calling out the installer. Any one of these adjustments could restore the performance. The shower cycles from HOT to COLD Water too HOT Water too COLD Spray pattern poor Water takes longer to heat up Water goes cold while using shower Broken parts The shower temperature is set too hot causing the thermal cut-out (safety device) to operate.
ADDITIONAL ACCESSORIES COMMON SPARE PARTS Additional accessories and Spare Parts can be supplied from Creda Sales 0844 372 7766 Please Note:- The fitting of Spare Parts must be supervised by a suitably qualified person. Chrome 1.25 metre Shower Hose Chrome Multi-Mode Accessories Chrome Premium Accessories Chrome Curved Accessories Curtain and Rail Pack Water Isolating Valve Cat Cat Cat Cat Cat Cat No. No. No. No. No. No.
HOW YOUR FLORIDA PLUS SHOWER WORKS 1. Water is heated instantaneously as it flows over the heating elements in the copper cylinder (Diagram 9). 2. The heaters are only switched on when sufficient water is flowing. This is done automatically with a switch which works on water pressure and is indicated by two or three lights illuminating depending on the power selected by knob “A”. 3. The water is turned on and off by the solenoid valve built into the shower. This is switched on when button “B” is pressed. 4.
GUARANTEE AND CONTACT DETAILS : GUARANTEE Terms and Conditions for UK (outside UK contact your local distributor) We guarantee this product for a period of 24 months from the date of purchase.
HOW TO USE YOUR FLORIDA PLUS SHOWER (SUMMARY) 1. Ensure the electricity and water are turned on to the unit. 2. Press the start / stop button “B”. This will turn the shower on, the water will flow and the indicator lights will glow showing chosen Power Selection. We recommended you do not enter the water spray during this period, especially if the shower has just been used. Knob “A” controls the power selection. Select “FULL HEAT ”, “HALF HEAT ” or “COLD ”.
