operating Instructions Manual Arezzo Electric Radiator Models: ARE050 / ARE075 / ARE100 / ARE150 / ARE200 These instructions should be read carefully and retained for future use. Note also the information presented on the appliance.
IMPORTANT These instructions should be read carefully and retained for future use. Note also the information presented on the appliance. IMPORTANT SAFETY ADVICE When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons, including the following: IMPORTANT – The wall bracket supplied with the appliance must be used. WARNING - DO NOT USE THIS HEATER IN THE IMMEDIATE SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING POOL.
WARNING – THIS APPLIANCE MUST BE EARTHED The electrical installation must be carried out by a competent electrician, and be in strict accordance with the current I.E.E. Regulations for Electrical Equipment in Buildings. The wires in this mains lead are coloured in accordance with the following code: GREEN AND YELLOW: EARTH BLUE: NEUTRAL BROWN: LIVE BLACK PILOT WIRE - see also ‘Pilot Wire Connection’. The heater is fitted with a length of flexible cable type H05VV-F size 4 x 1.
General The heater is designed for wall mounting using the wall bracket supplied. It should only be operated when in the upright position as shown - see Fig. 1 and Fig. 2. All models are splash proof to IP24 standard and may be used in bathrooms, however not in the immediate vicinity of baths, showers, water connections, wash basins or swimming pools. Before connecting the heater check that the supply voltage is the same as that stated on the heater.
Fig. 2 Fig. 1 150 mm (Min) A Shelf 546 mm 300 mm 105 mm 150 mm (Min) Fig.
Notes to the Installer Test Mode When the heater is connected via a pilot wire system, the test mode allows the installer to confirm that the heater is responding correctly to the incoming pilot wire signal. Pilot wire mode must be enabled in the heater’s settings in order for the appliance to be controlled by a Creda controller with pilot wire connection. Press Menu, Back and Enter for ten seconds to enter the service menu, select Pilot Wire and press Enter. Select Enable.
User introduction Thank you for choosing the Creda Arezzo Electric Radiator. We manufacture the highest quality heating products for use in a wide variety of environments. This product has been designed to incorporate the latest, most advanced technologies to give you maximum control over your heating. The system allows for the simple setting of required time and temperature, and includes many energy-saving features which work automatically to help keep you warm for less.
Quick Start Guide This guide is for quick reference only. Please refer to the operating section for further information. How Does the Heater Control Work? The control allows you to choose when you want heat and at what temperature. When using a timer mode (see below), Comfort On will display on the home screen to tell you when the heater is maintaining the temperature displayed. Comfort Off will display when the heater is outside of a timed heating period.
Which Timer Mode is Best for Me? The heater leaves the factory set in Out All Day mode. If you are out during the day and only require heat in the mornings and evenings then this mode will suit your lifestyle and you won’t need to alter anything. If you are in during the day then you should select the Home All Day mode which is a single heating period. The times of these modes can be modified, or the User Timer mode can be used to give you four periods of heating split throughout the day.
Operation The controls are located on the top right of the heater. The heater is fitted with an adjustable electronic controller consisting of a display screen and six touch sensitive buttons. 1 2 4 5 1 Display Screen 2 ‘Menu’ Button 3 ‘Back’ Button 4 ‘Up and Down’ Arrows 5 ‘Enter’ Button 6 Heating Status 7 ‘Advance’ Button Comfort On 6 3 7 The heater is fitted with an adjustable thermostat enabling the room temperature to be controlled. The minimum room temperature is 7°C.
Control Functions The heater controls can be easily adjusted by using the six buttons on the User Interface. 1. The Display Screen shows the options available at each stage of adjustment. 2. Menu – displays the main options list; Date/Time – Set the date and time. Mode – Set the mode of operation. Options – Temperature units, daylight savings time, lock settings and service information. 3. Back returns to the previous programming stage. 4.
Main Screen After 30 seconds of inactivity the heater will default back to the Main Screen. Here the chosen temperature is displayed along with the mode of operation. Any use of the Advance function will be displayed here, and pressing Enter will show the functions which are enabled. When left inactive for a long period of time this display will ‘sleep’ and the text will disappear. Press any button for its return.
Modes of Operation The heater comes pre-programmed with a set of heating profiles. There are four options available - three preset and one user adjustable timer; 1. Out All Day (pre-programmed) - has the following preset times Monday to Sunday, which can be altered if desired; 07.00 until 08.30 17.30 until 22.00 2. Home All Day (pre-programmed) - has the following preset times Monday to Sunday, which can be altered if desired; 08.00 until 21.00 3.
Choosing and Setting a Mode Timer Modes To choose a timer mode press Menu and to select Mode, then press Enter. Now select Timer Mode, again using the Enter button. Select the mode required, by pressing the or and Enter buttons. For options Out All Day, Home All Day and User Timer, three choices are available - Select, Preview and Modify. • Select - choose this timer option. • Preview - view the times currently set. • Modify - change the times currently set.
If anticipatory control is disabled, the heater will not operate until the beginning of the heating period. This should be taken into consideration when setting the heating periods (See note below and page 17). In Holiday mode the number of days that the room will be unoccupied can be adjusted together with the required room temperature. Press and to choose a holiday period between 1 and 300 days, then press the Enter button.
Advance The Advance function allows the heating profile of the appliance to be changed temporarily. When a timer has been selected, the Advance function is used to begin the next Comfort On mode early. If the heater is in Comfort Off mode and heat is required, press the Advance button. Advance Home All Day Comfort On If the heater is in Comfort On and heat is not required, press the Advance button and the heater will turn off until the beginning of the next Comfort On period.
Child Lock To lock the controls press Back and Enter for three seconds. Child Lock will appear at the bottom of the screen. To unlock the control repeat the action of pressing Back and Enter for three seconds. NOTE: The controls cannot be adjusted when child lock is active. Child Lock User Information Press and hold Enter for five seconds to display the User Information menu; SP Range (set point) allows adjustment of the maximum temperature. Open Window detection (OW).
Energy Saving Tips The energy we use to heat, light and power our 6. Treat your hot water tank... homes contributes over a quarter of the UK’s give it a jacket An insulating jacket for hot carbon emissions, the principle contributor to water tanks costs only a few pounds and pays climate change. for itself within months. Fit one that’s at least 75mm (3”) thick and you could save £10-15 a Around half the energy used in the home year. is for heating and hot water, so using your 7.
Important During the initial operation, some odour may be noticed due to the newness of materials used in manufacture. This is normal and will disappear after a short period or use. It is however advisable to keep the room well ventilated. Cleaning WARNING - ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER. Before commencing cleaning, disconnect the electricity supply to the appliance and allow it to cool. The outside can be cleaned by wiping it over with a soft damp cloth and then dried.
Patent/Patent Application This product is protected by one or more of the following patents or patent applications: Great Britain: GB1304025.8 International: PCT/EP2014/054404 This product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2 and EN60555-3.
