Specifications
Table Of Contents
- Coverpage
- Safety Instructions
- Revision History
- Contents
- Introduction
- 1 Outline
- 2 Explanation of Functions
- 3 Q-PLC Multi-CPU
- 4 Q Motion CPU
- 5 SFC Program
- 6 SV22 Servo Programs
- 6.1 Servo program
- 6.1.1 Servo program configuration
- 6.1.2 List of servo commands
- 6.1.3 Linear control
- 6.1.4 Circular interpolation control using auxiliary point designation
- 6.1.5 Circular interpolation control using radius designation
- 6.1.6 Circular interpolation control using center point designation
- 6.1.7 Fixed-dimension feed control
- 6.1.8 Speed control
- 6.1.9 Speed/position changeover control
- 6.1.10 Speed changeover control
- 6.1.11 Constant-speed control
- 6.1.12 Repeated control (for speed changeover control and uniform speed control)
- 6.1.13 Simultaneous start
- 6.1.14 Zero point return
- 6.1.15 Position follow-up control
- 6.1.16 High-speed oscillation control
- 6.1.17 Helical interpolation control with auxiliary point designated
- 6.1.18 Helical interpolation control with radius designated
- 6.1.19 Helical interpolation control with center point designated
- 6.1.20 Current value change
- 6.1 Servo program
- 7 Operation Control Program
- 8 Windows Personal Computer Operations
- 9 Basic Practice Using the SV22 Real Mode
- 10 Applied Practice with SV22 Real Mode
- 10.1 Details of practice
- 10.2 Q172CPU practice machine system configuration
- 10.3 Practice SFC programs
- 10.4 Writing to the motion CPU
- 10.5 Program for operation
- 10.5.1 JOG operation
- 10.5.2 Main routine SFC program (real mode operation)
- 10.5.3 Execution of servo program (motion control step)
- 10.5.4 Stopping
- 10.5.5 Error reset
- 10.5.6 Current value change
- 10.5.7 Speed change (CHGV)
- 10.5.8 Reading actual current value
- 10.5.9 Continuous positioning
- 10.5.10 M code function
- 10.5.11 Indirect setting of servo program address
- 10.6 Operating the practice machine
- 11 Practicing with the SV22 Virtual Mode
- 11.1 Mechanism program
- 11.2 Details of practice
- 11.3 Starting up SW3RN-CAMP and creating the cam
- 11.4 SFC program for virtual mode
- 11.5 Editing the mechanism
- 11.6 Writing to the motion CPU
- 11.7 Reading of sequence program from Q-PLC CPU
- 11.8 SFC program for practice
- 11.9 Practice machine operations
- 11.10 Exercise (Roller setting)
- Appendix
A - 18
Manual pulse generator
[F130]
D720 = 100 //1-axis 1-pulse input magnification
setting
D721 = 100 //2-axis 1-pulse input magnification
setting
D714L = H00000001 // Control of 1-axis by P1
D716L = H00000002 // Control of 1-axis by P2
SET M2051 // P1 manual pulse generator permit
flag ON
SET M2052 // P2 manual pulse generator permit
flag ON
[G130]
!(!PX2*PX1) //
Manual pulse generator mode
END?
[F131]
RST M2051 // P1 manual pulse generator
permit flag OFF
RST M2052 //P2 manual pulse generator
permit flag OFF
END
Set as follows to execute the manual pulse generator
operation of 1-axis using manual pulse generator P1, and
that of 2-axis using manual pulse generator P2.
• Set the 1-pulse input magnification for 1-axis, 2-axis.
• Set the manual pulse generator axis setting register to
control 1-axis with P1 and 2-axis with P2.
• Turn ON the P1 and P2 manual pulse generator permit
flag.
For safety purposes, the manual pulse generator permit
flag is turned OFF at the end of manual pulse generator
mode, so that the manual pulse generator operation is
not continued after transferring to another mode.