Content 4-5 PC Mode………......................………….........……....16 Chapter 1 Attention 1-1 1-2 1-3 1-4 . Safety Precautions……….....................…....…..…...2 How to Maintain Your Camera…….........……..........2 Before Using Your Camera…….............……...........2 Package Contents………........................………..…...3 Chapter 5 Preparing Your Camera 5-1 5-2 5-3 5-4 5-5 Chapter 2 Getting to Know Your Camera 2-1 Names of Parts……….....................…………...…......4 2-2 Specifications.....................
1. Attention 1-2 How to Maintain Your Camera Please read this manual carefully before using the camera and follow the instructions to avoid damage caused by improper operation. ● If the lens, LCD monitor or viewfinder surface is dirty, use a lens brush or soft cloth to wipe it clean. Avoid touching the lens with your fingers. ● Avoid scratching the lens, LCD monitor or viewfinder surface by placing the camera away from solid objects.
1-4 Package Contents law. ● Notes on the LCD (Liquid Crystal Display) monitor In the rare event that the LCD monitor breaks and the liquid within spills, follow the care instructions below: 1. If the liquid makes contact with the skin: Wipe the skin dry and wash it thoroughly with water. 2. If the liquid gets into the eye: Rinse with water immediately for at least 15 minutes. Consult a physician as soon as possible. 3.
2.
Rear View (1) Macro LED (2) Status LED (3) Mode Display Button (4) Mode Button (5) Set Button (6) Function Key (7) Macro Button (8) USB Cover (9) USB Port (10) LCD Monitor 5
● Recordable Image Numbers (16MB): 2-2 Specifications 800 x 600 Lens: f=8.79mm Image Sensor: 1/2" CMOS with 2.0 mega pixels Focus: F / 2.8 Sensitivity: ISO 100 White Balance: White Balance: Auto, Sunny, Tungsten, Fluorescent. ● Shutter: Electrical ● Shutter Speed: 1/4 sec. ~ 1/2000 sec.
System requirement (Macintosh Computer) OS Mac® OS X 10.1 or above CPU PowerPC® 601 processor or higher Memory 64 MB memory or above HDD Minimum 10MB free disk space on the hard drive Others One standard USB 1.1 or USB 2.
3.
3-3 Power Supply configuration before the camera is turned off unless the "Reset Default" has been selected to restore its factory anticipated settings. 1.Resolution 2. Image Quality 3.Language 4.White balance 5.EV value 6.Frequency 7.PC MODE ● Gently slide the lens cover to the left as illustrated. A long beep indicates that the camera is turned on. 3-4 Shutter Button ● To turn off the camera, gently slide the lens cover to the right. This camera is designed for 2-step shutter function.
3-8 Mode Display Button 3-5 Mode Selection ● Please press and hold ” ” button for 2 seconds to enter mode selection menu including “Play Mode” “Setup Mode” “Record Mode" “Movie Mode” "Function Selection” Press this button you can change the LCD Monitor to several displays. Standard→Image only→LCD OFF→Standard . 3-6 Function Key 3-9 Macro Button You can select between Standard and Macro mode under Record mode and Movie mode by the switch on left side of the camera.
4. Navigation Modes and Menus Index for Quick Menu: 4-1 Record Mode ↑ For more information, please refer to the "3-2 LCD Monitor Display" section on page 8.
2. Slideshow 4-2 Play Mode Start Auto Play (1) Possible Number of Shots (2) Remaining Battery Power 3. DPOF (Digital Print Order Format) Settings ● There are three options when printing images with DPOF: Printing one image, printing all images and the option of printing the recorded date or not. ● DPOF function can only be operated when the printer settings of the memory card is inserted, and not active with the internal memory of the camera.
4-3 Movie Mode (1) (2) (3) (4) (5) 13 Movie Mode Recorded Movie Time (seconds) Recording Remaining Battery Power Time/Date
3. White Balance 4-4 Setup Mode (Auto) (Sunny) (Fluorescent) (Tungsten) 1. Image Resolution 2048x1536 800x600 1600x1200 1280x960 4. EV Compensation 2.
7. Light Frequency Select the correct frequency type (50Hz or 60Hz) according to your region. 5. OSD Language 8. Format Media ※If the memory card has been inserted, it would only format the memory card, and not the internal memory. 6. Date/Time 9.
4-5 PC Mode 16
5. Preparing Your Camera 5-1 Attaching the Strap 5-2 Loading Batteries ● Turn the camera off first. ● Insert 2 x AAA alkaline batteries or rechargeable batteries. Please make sure the batteries are fully charged. If the batteries are low power, please change the batteries as soon as possible to maintain operation normality. ※ If the battery power indicator only shows one black block, the flash light would be disabled: If lower than 1.
● Close and lock the battery cover. NOTE: Do not open the cover roughly to avoid damaging the battery compartment cover. ※ If the battery power indicator only shows one black block, the flash light would be disabled. ● Insert the memory card according to the indicated arrow. 2. Removing the Memory Card ※ When the battery indicator turns red, recording of still pictures and movies would be disabled. ※ The Date/Time would be stored for approximately 3 minutes during battery change.
5-4 Setting Up the OSD Language memory card into the slot. If the memory card is full or contains other images, you can press the Mode Button to Format of the Setup Mode the memory card. Before using the camera, please select "Language" to set the OSD language by pressing the Mode Button to format to Setup Mode . There are 7 options for your selection: English, Chinese, French, German, Italian, Japanese, Spanish. ● There is 16MB internal memory built-in in the digital camera for Image Storage.
6. Getting Started Record Mode through Mode Button 6-1 Setup Mode the Function key By using the Setup Mode, you can adjust the basic camera settings, including: Image Size, Image Quality, White balance, and EV Compensation. General setting format and factory default setting. Setup for language, date/time and light frequency is as follows: to move to and use Function key 3. You can use to select two flash light modes when using the camera: Auto, and Off. . 3.
※If the icon appears on the LCD Monitor for low battery power, please change the batteries immediately to maintain operation normality. ※ The countdown for the Self-timer is 10 seconds. ※ There are 4 types of resolutions offered by the camera: 2048x1536, 1600x1200, 1280x960, and 800x600. ※ Please pay attention to the distance between the camera and the object when using the Flash Light. The internal built-in Flash Light of this camera is effective within 1.5 meter.
screen, the LCD monitor will then display the menu. 4. The top left hand corner will display the recorded time in red while you are recording the movie pictures. 5. The green LED will be on when the Macro key on the left hand side of the camera is toggled to Macro Mode. 6-5 PC Mode 6. You can use Display button to toggle between display modes while recording movie pictures: normal display mode and image display mode.
6. Please connect the USB cable to the camera and the PC when the diagram USB Connection pops up the screen. 7. A new item – removable disk will be added into my computer after the system installation is completed. 8. You may start to operate with the newly added removable disk (SD device) offered by the digital camera. ● PC Camera The digital camera can be treated as a PC camera or a Web Cam. Please follow the instructions mentioned below: 1.
7. Driver Installation 7-1 Installing the Camera Driver for PC 3. Click Install Driver to install camera driver of the digital camera. The screen will appear the following message (for Windows XP only): You can use the PC Camera and Mass Storage functions of the camera via PC. To install the proper camera driver, perform the following: 1. Insert the installation CD into the CD-ROM drive. 2.
3. Please click on the Arcsoft PhotoImpression installation, the screen will appear the following diagram: 7-2 Installing the Application for PC Arcsoft application installation (In case of Photo Impression) 1. Insert the software CD-ROM supplied by the package into the CD-ROM drive. 2. The Auto-run program will be executed and the welcome screen will appear the following message : (If your CD-ROM drive doesn't support the auto-run function, please double click on the "My Computer" icon on the desktop.
8. Please select the folder where you want to install the application in. 7. Please follow the installation wizard to select the folder location and application components.
9. After the installation the following diagram will appear. Press Finish to complete the application installation.
