User’s Guide Creative Broadband Blaster DSL Router 8015U Information in this document is subject to change without notice and does not represent a commitment on the part of Creative Technology Ltd. The software described in this document is furnished under a license agreement and may be used or copied only in accordance with the terms of the license agreement. It is against the law to copy the software on any other medium except as specifically allowed in the license agreement.
Contents
Contents Introduction DSL Router information............................................................................................................................... v Package Contents........................................................................................................................................... v System requirements....................................................................................................................................
In Windows Me................................................................................................................................ 3-7 In Windows 98 SE ........................................................................................................................... 3-9 4 Configuring your DSL Router Understanding DSL Router configurations........................................................................................ 4-1 Connecting to your DSL Router’s Home Page ................
Appendixes A Technical Specifications B Troubleshooting Connection to your DSL Router’s home page................................................................................ Connection to the Internet.................................................................................................................... LED Status.................................................................................................................................................... Normal Setup Status.............
Introduction
Introduction Thank you for purchasing Creative Broadband Blaster DSL Router 8015U. Developed with the most advanced Digital Subscriber Line (DSL) today, the DSL Router provides you with high-speed broadband Internet connection using an existing phone line. Enjoy speedy file transfers, watch Internet movies, videoconference, and view videos without any long waits.
System requirements In order for your DSL Router to operate properly, be sure that your computer meets the following minimum system requirements: You will need a hub if you wish to connect more than 2 computers to your DSL Router. Using Ethernet connection Depending on your computer’s configurations, you can choose to install your router using the Ethernet or USB port. Using USB connection ❑ ❑ ❑ ❑ ❑ ❑ Compatible with all operating systems.
Using this document These icons highlight useful or urgent information: ❍ Tip. This tells you about shortcuts or hints relating to a feature. ❍ Note. This highlights additional or important information about a feature. ❍ Caution! This highlights proper usage of your device. Use this information to avoid situations involving risk. ❍ Warning! This warns you of possible hazards to yourself or your device, which may result in injury or damage.
Installing your DSL Router
Installing your DSL Router This section will guide you through the process of setting up your DSL Router. Place your DSL Router in front of you as you go through this section to help you to identify the various components of your modem. Power LED Ready LED Link LED Activity LED Figure 1-1: Front view of your DSL Router LED Indication POWER LED lights up when your DSL Router is connected to a power source. READY LED flashes when your DSL Router is initializing the DSL connection.
Phone port DSL LINE port Ethernet port Power connector USB port Reset button Figure 1-2: Back view of your DSL Router Port/Connector Indication PHONE PORT Connects to the telephone via a microfilter. DSL LINE PORT Connects to the telephone wall outlet using the provided RJ-11 phone cable. ETHERNET PORT Connects to the Ethernet port on your computer using the Straight Ethernet cable. If you are connecting your DSL Router using the Ethernet port, do not connect the USB port on the same computer.
Setting up your DSL Router Depending on your computer’s configurations, you can choose to install your DSL Router using the Ethernet or USB port on the same computer. Do not install your DSL Router using both connections on the same computer. Using the Ethernet port Before setting up your DSL Router, be sure that the Network Interface Card in your computer is installed and functioning properly. DO NOT use the USB port on your DSL Router if you are using the Ethernet port on the same computer.
2. Locate a telephone wall outlet and unplug any telephone cable that is connected to it. 3. Connect one end of the RJ-11 phone cable provided into the telephone wall outlet. 4. Connect the other end into the DSL LINE port of your DSL Router. 5. Connect the small round plug of the power adapter provided to the DSL Router’s power connector and plug your power adapter into a power outlet. 6. Turn on the power supply. 7.
Using the USB port Use Figure 1-5 as a reference when following these instructions to set up your DSL Router. 1. Connect the USB cable to the USB ports on your computer and DSL Router. Ethernet port DO NOT use the Ethernet port on your DSL Router if you are using the USB port on the same computer.
5. Connect the small round plug of the power adapter provided to the DSL Router’s power connector and plug your power adapter into a power outlet. 6. Turn on the power supply. 7. If you have telephones and fax machines sharing the same phone line, connect them to the telephone wall outlet or DSL modem phone port with microfilters as shown below. The microfilters will help to ensure voice and data quality.
Configuring Your Network Interface Card
Configuring Your Network Interface Card Before You Begin Before using your DSL Router, you need to configure your Network Interface Card. If you are connecting your DSL Router using the USB port, skip this chapter and go to "Installing the USB Driver" on page 3-1. In Windows XP/Windows 2000 1. After setting up your DSL Router, turn on your computer. 2. In Windows XP, click Start -> Settings -> Control Panel and double click the Network Connections icon.
4. When the dialog box similar to Figure 2-2 appears, be sure that the name of your network card is displayed in the first box. 5. In the list below the box, click the Internet Protocol (TCP/IP) check box to select it. 6. Click the Properties button.
7. When the dialog box similar to Figure 2-3 appears, click Obtain an IP address automatically option, and then click the OK button. 8. When the Local Area Connection Properties dialog box appears, click the OK button. After configuring your Network Interface Card, you need to configure your DSL Router. See "Configuring your DSL Router" on page 4-1.
In Windows Me/Windows 98 SE 1. After setting up your DSL Router, turn on your computer. 2. Click Start -> Settings -> Control Panel. 3. When the dialog box similar to Figure 2-4 appears, double-click the Network icon. Figure 2-4 4. When the dialog box similar to Figure 2-5 appears, click the Configuration tab. 5. Click the adapter that has the name of your Ethernet card, for example, TCP/IP->Intel 8255x-based PCI Ethernet Adapter (10/100). 6. Click the Properties button.
7. When the dialog box similar to Figure 2-6 appears, click the IP Address tab. 8. Click the Obtain an IP address automatically option, and then click the OK button. 9. In the Network window, click the OK button. 10. Restart your computer to let the changes take effect. After configuring your Network Interface Card, you need to configure your DSL Router. See "Configuring your DSL Router" on page 4-1.
Installing the USB Driver
Installing the USB Driver Installing the USB Driver Before using your DSL Router, you need to install the USB driver. If you are connecting your DSL Router using the Ethernet port, skip this chapter and go to "Configuring Your Network Interface Card" on page 2-1. In Windows XP If you want to install the applications later, from the Autoplay window, click the Exit button and proceed to step 6 to install the USB drivers. 1.
6. When the Found New Hardware Wizard dialog box (Figure 3-1) appears, click the Install from a list or specific location (Advanced) option, and then click the Next button. 7. When the dialog box similar to Figure 3-2 appears, click the Include this location in the search check box to select it. 8. Click the Browse button to locate the driver file in d:\Drivers\WinXP (replace d:\ with the drive letter of your CDROM drive), and then click the OK button. 9. Click the Next button.
10. If the dialog box similar to Figure 3-3 appears, click the Continue Anyway button. For more information, refer to "Difficulties In Windows XP" on page B-5. 11. Click the Finish button. 12. If prompted, restart your computer. After installing the USB driver, you need to configure your DSL Router. See "Configuring your DSL Router" on page 4-1.
In Windows 2000 If you want to install the applications later, from the Autoplay window, click the Exit button and proceed to step 6 to install the USB drivers. 1. After you have set up your DSL Router, as described on page 1-5, turn on your computer. 2. Insert the Installation CD into your CD-ROM drive. The disc supports Windows Autoplay mode and starts running automatically. If the Autoplay window appears, click the Yes button to accept the Software License Agreement. 3.
7. When the dialog box similar to Figure 3-5 appears, click the Search for a suitable driver for my device (recommended) option, and then click the Next button. Figure 3-5 8. When the dialog box similar to Figure 3-6 appears, click the Specify a location check box to select it, and then click the Next button. 9. In the dialog box that appears, click the Browse button to locate the driver file in d:\Drivers\Win2K (replace d:\ with the drive letter of your CD-ROM drive), and then click the OK button.
11. If the Digital Signature Not Found dialog box (Figure 3-7) appears, click the Yes button. 12. In the next dialog box that appears, click the Finish button. 13. If prompted, restart your computer. After installing the USB driver, you need to configure your DSL Router. See "Configuring your DSL Router" on page 41.
In Windows Me If you want to install the applications later, from the Autoplay window, click the Exit button and proceed to step 5 to install the USB drivers. 1. After you have set up your DSL Router, as described on page 1-5, turn on your computer. 2. Insert the Installation CD into your CD-ROM drive. The disc supports Windows Autoplay mode and starts running automatically. If the Autoplay window appears, click the Yes button to accept the Software License Agreement. 3.
7. Click the Browse button to locate the driver file in d:\Drivers\WinMe (replace d:\ with the drive letter of your CD-ROM drive), and then click the OK button. 8. Click the Next button. 9. In the dialog box that appears, click the Next button. 10. Click the Finish button. 11. When prompted, restart your computer. After installing the USB driver, you need to configure your DSL Router. See "Configuring your DSL Router" on page 4-1.
In Windows 98 SE If you want to install the applications later, from the Autoplay window, click the Exit button and proceed to step 6 to install the USB drivers. 1. After you have set up your DSL Router, as described on page 1-5, turn on your computer. 2. Insert the Installation CD into your CD-ROM drive. The disc supports Windows Autoplay mode and starts running automatically. If the Autoplay window appears, click the Yes button to accept the Software License Agreement. 3.
7. When the dialog box similar to Figure 3-11 appears, click the Search for the best driver for your device (Recommended) option, and then click the Next button. Figure 3-11 8. When the dialog box similar to Figure 3-12 appears, click the Specify a location check box to select it. 9. Click the Browse button to locate the driver file in d:\Drivers\Win98SE (replace d:\ with the drive letter of your CD-ROM drive), and then click the OK button. 10. Click the Next button.
11. When the dialog box similar to Figure 3-13 appears, click the The Updated driver (Recommended) option, and then click the Next button. Windows 98 users may be prompted to insert the Windows 98 installation CD into the CD-ROM drive during installation. 12. Click the Next button. 13. Click the Finish button. 14. When prompted, restart your computer. After installing the USB driver, you need to configure your DSL Router. See "Configuring your DSL Router" on page 4-1.
Configuring your DSL Router
Configuring your DSL Router Understanding DSL Router configurations Your DSL Router can be configured in several ways. Consult your Internet Service Provider for the configuration that best suits you. You need to configure your DSL Router just once, unless your Internet Service Provider changes the configuration settings. Your DSL Router supports the following configurations: ❑ PPPoA LLC/PPPoA VC-Mux/PPPoE LLC — this requires a User ID and Password for authentication.
Connecting to your DSL Router’s Home Page Disable any proxy server in use before accessing the DSL Router home page. See "Disabling the Proxy Server" on page 4-11. Before proceeding, make sure that you have configured your Network Interface Card or installed the USB device drivers successfully. You need to connect to your DSL Router’s home page to configure your DSL Router. 1. If your DSL Router is connected using the Ethernet or USB port, the Link LED will light up. 2.
Configuring your DSL Router PPPoA/PPPoE 1. After connecting to your DSL Router’s home page, move your mouse over Configuration on the left pane and select System Settings. 2. When the window similar to Figure 4-2 appears, select PPPoA or PPPoE in the encapsulation mode. 3. Type in the VPI and VCI values provided by your Internet Service Provider in their respective boxes. 4. Click the Next button.
5. When the window similar to Figure 4-3 appears, type in the user name and password provided by your DSL service provider. 6. Click the Next button. 7. When the window similar to Figure 4-4 appears, select the DHCP server Enable option. 8. Click the Next button.
9. When the window similar to Figure 4-5 appears, click the Next button. 10. When the window similar to Figure 4-6 appears, check that all settings are correct. Click the Finish button. Figure 4-5 11. Click the OK button. 12. Wait for your DSL Router to connect to the Internet.
RFC 1483 Routed 1. After connecting to your DSL Router’s home page, click Configuration on the left pane and select System Settings. 2. When the web page similar to Figure 4-7 appears, select RFC 1483 Routed in Encapsulation Mode. 3. Type in the VPI and VCI values provided by your Internet Service Provider in their respective boxes. 4. Click the Next button. Figure 4-7 5. If you are using a Static WAN IP address, you must configure the WAN IP address, subnet mask, gateway and DNS IP address.
6. When the LAN Settings web page (Figure 4-9) appears, select the DHCP Server Enable option and click the Next button. 7. When the web page similar to Figure 4-10 appears, click the Next button.
DO NOT turn off the computer or DSL Router when the DSL Router configuration is being saved. 8. When the web page similar to Figure 4-11 appears, click the Finish button. 9. Click the OK button. 10. Wait for your DSL Router to connect to the Internet. You can now start surfing the Internet at high speed! If your DSL connection is charged on the basis of time online, turn off your DSL Router when it is not in use, to avoid unnecessary charges.
RFC 1483 Bridged IP Configuration DO NOT turn off the computer or DSL Router when your DSL router is restarting. If your DSL connection is charged on the basis of time online, turn off your DSL Router when it is not in use, to avoid unnecessary charges. 1. After connecting to your DSL Router’s home page, click Configuration on the left pane and select System Settings. 2. When the window similar to Figure 4-12 appears, select Bridge in Encapsulation Mode. 3.
6. In the web page that appears (Figure 4-14), click the Finish button. 7. Click the OK button. 8. Wait for your DSL Router to connect to the Internet.
Disabling the Proxy Server You need to disable any proxy server in use before accessing the DSL Router home page. Using Internet 1. Start Internet Explorer. Explorer 2. From the Tools menu, click Internet Options. 3. When the dialog box similar to Figure 4-15 appears, click the Connections tab. 4. Click the Never dial a connection option to select it and click the LAN Settings button. Figure 4-15 5.
Using Netscape Communicator 1. Start Netscape Communicator. 2. From the Edit menu, click Preferences. 3. When the dialog box similar to Figure 4-17 appears, double-click Advanced on the left pane and click Proxies. Depending on your computer’s settings, you may need to reset the proxy settings after accessing the DSL Router’s home page. Figure 4-17 4. When the dialog box similar to Figure 4-18 appears, click the Direct connection to the Internet option to select it, and then click the OK button.
Disconnecting from the Internet When you reconnect your DSL Router to the Internet, always make sure that you turn on your DSL Router before you turn on your computer. Wait at least 30 - 60 seconds for your DSL Router to connect to the Internet. In PPPoA and If you are using PPPoA or PPPoE configurations for your DSL router, you can disconnect from the Internet by turning off the main power supply to your DSL Router.
Configuring Advanced Features
Configuring Advanced Features This chapter tells you how to configure your DSL Router’s advanced settings. Upgrading Firmware To upgrade your DSL Router firmware, click the Firmware Upgrade link on the left pane. 1. When the web page similar to Figure 5-2 appears, click the Browse button. 2. Select the firmware upgrade file. 3. Click the OK button.
Changing Password 1. Connect to your DSL Router’s home page. See "Connecting to your DSL Router’s Home Page" on page 4-2. 2. Click Configuration -> Advanced Settings -> Change Password. 3. When the web page similar to Figure 5-2 appears, type in your new password, and then click the Submit button. 4. Click the OK button. 5. Wait for your DSL Router to restart.
IP Address Filter IP Address Filter allows you to filter out specified IP addresses. 1. Connect to your DSL Router’s home page. See "Connecting to your DSL Router’s Home Page" on page 4-2. 2. Click Configuration -> Advanced Settings -> IP Address Filter. 3. When the web page similar to Figure 5-3 appears, type the LAN Client Name and IP Address that you want to filter. 4. Click the Filtered check box to select it. 5. Click the Submit button. 6. Click the OK button. 7.
DMZ Enabling DMZ will allow access from the Internet to your LAN and may compromise on your security. Demilitarized Zone (DMZ) is a computer host or small network inserted as a "neutral zone" between a company's private network and the outside public network. It allows access from the Internet to the host computer. 1. Connect to your DSL Router’s home page. See "Connecting to your DSL Router’s Home Page" on page 4-2. 2. Click Configuration -> Advanced Settings -> DMZ. 3.
Port Forwarding Enabling port forwarding will allow access from the Internet to your LAN and may compromise on your security. Port forwarding, also known as port mapping, allows you to direct TCP/UDP ports to computers on your LAN. This allows access from the Internet to your LAN. 1. Connect to your DSL Router’s home page. See "Connecting to your DSL Router’s Home Page" on page 4-2. 2. Click Configuration -> Advanced Settings -> Port Forwarding. 3.
LAN Client Table The feature allows you to add LAN clients. 1. Connect to your DSL Router’s home page. See "Connecting to your DSL Router’s Home Page" on page 4-2. 2. Click Configuration -> Advanced Settings -> LAN. 3. When the web page similar to Figure 5-6 appears, type in the LAN Client Name and IP address. 4. Click the box under Selected to select it. 5. Click the Add button. 6. Wait for your DSL Router to restart.
MAC Address Filtering Media Access Control (MAC) filtering is used to block data transfer on your LAN. The MAC address of a Network Interface device is a 12 digit hexadecimal number that is unique. 1. Connect to your DSL Router’s home page. See "Connecting to your DSL Router’s Home Page" on page 4-2. 2. Click Configuration -> Advanced Settings -> MAC Address Filter. 3. When the web page similar to Figure 5-7 appears, under Add, click the box to select it. 4.
Technical Specifications
Technical Specifications This section provides certain technical specifications for your Creative Broadband Blaster DSL Router 8015U. Data Encapsulation Protocol ❑ RFC 2684/1483 Bridge/Routed, PPPoA, PPPoE ADSL Line Interface ❑ ❑ ❑ ❑ ❑ Electrical ❑ Power adapter with output 16 V AC, 750 mA Interface ❑ Ethernet 10/100 Base-T (LAN). MDI-X ❑ RJ-11 (WAN) ❑ USB 2.0 Full Speed Dimensions ❑ Length: 145 mm / Width: 125 mm / Height: 30 mm Compliance ❑ ❑ ❑ ❑ ❑ ❑ ❑ ANSI T1.413 issue 2 ITU-T G.992.1 (G.
Troubleshooting
Troubleshooting If you have a technical problem with this product, you may wish to consult our self-help tool "Knowledgebase" for online troubleshooting and solutions. Go to www.creative.com and select your region. Connection to your DSL Router’s home page The Web browser does not connect to the DSL Router home page. You are not using the correct IP address. Try the following: ❑ Be sure that you have typed the default IP address as 192.168.1.1.
Connection to the Internet My DSL Router does not connect to the Internet. You did not set up your DSL Router correctly. Try the following: ❑ Be sure that if your DSL Router is connected to your computer through a hub, you are using a crossed Ethernet cable. Also, be sure that you have configured your DSL Router correctly. For more information, see "Configuring your DSL Router" on page 4-1. ❑ If your computer is connected to your DSL Router using a USB cable, be sure that you have installed the USB driver.
LED Status Observe the LEDs on your DSL Router to check if the device is functioning properly. Normal Setup Status When your DSL Router is turned on, the Power LED lights up. After several seconds, all the LEDs will go into their correct states. See "Installing your DSL Router" on page 1-1 for more information. The Power LED on my DSL Router does not turn on. Your DSL Router is not properly powered by an external power source.
The Ready LED on the DSL Router keeps flashing. There is no DSL service subscription. There is too much noise on your telephone line. Your Internet Service Provider may be experiencing problems. Check on the following: ❑ Be sure that the telephone cable is connected correctly to your DSL Router. ❑ Try connecting again after a few minutes as external interference can cause disruptions to your DSL line.
Difficulties In Windows XP A Hardware Installation error message appears on a Windows XP operating system when a driver is being installed. At the time of this product's release, Microsoft strongly encouraged companies to submit their hardware solutions for certification. If a hardware device driver is not submitted, or does not qualify, for Microsoft certification, a warning message similar to the one below appears. You may see this message when installing this driver or update.
Frequently Asked Questions
Frequently Asked Questions Can my DSL Router work with Operating Systems other than Windows? Yes, if you are connecting your DSL Router using the Ethernet port. Ethernet port connection is operating system independant. Currently, Technical Support only provides support for Windows-based operating systems. If you are, however, connecting your DSL Router using the USB port, your DSL Router will only work with Windows XP, Windows 2000, Windows Me and Windows 98 SE.
Glossary
Glossary This section offers a short explanation of some of the common networking and DSL terminologies. ADSL Asymmetric Digital Subscriber Line — A Digital Subscriber Line (DSL) technology that allows digital data to be sent over existing telephone lines. Though many different DSL technologies have been developed, ADSL is the most popular among individuals and small businesses because it offers higher downstream (or download) than upstream (or upload) data rates.
DSL Digital Subscriber Line — A technology that transforms ordinary telephone lines into high-speed digital lines for fast Internet access. This technology uses a digital coding technique to get large capacity out of existing phone lines without interfering with regular services — one can use the phone and surf the Internet at the same time. In this way, DSL provides simultaneous Internet and voice/fax capabilities over a single telephone line without any interference.
IP Address The address for a computer on a TCP/IP network. An IP address identifies a particular machine on a network. The format of an IP address is a 32-bit numeric address written as four numbers separated by periods. Each number can be 0 to 255, for example, 11.160.10.240 is an IP address. Any machine connected to the Internet is assigned an IP address. ISP Internet Service Provider — An organization that provides Internet access to computer users.
RFC 1483 A standard method for linking different devices across networks and which assures “interoperability”. RJ-11 A connector/socket for two pairs (four wires) of twisted pair cables that is used primarily to connect telephone equipment. Router A hardware device connecting two separately functional networks that use the same or different protocols. Routers look at the destination addresses on data packets, and then decide which route to send them on.
