Owner's Manual And Assembly Instructions For FSC certified products look for the FSC label SGS-COC-005310 1996 Forest Stewardship Council A.C.
Thank you for purchasing a Creative Cedar Designs Playcenter. We hope it will bring you and your children many years of safe and enjoyable backyard fun.
STOP…PLEASE READ!! IF YOU HAVE ANY QUESTION OR ARE MISSING A PART, PLEASE DO NOT CONTACT THE RETAILER THAT YOU PURCHASED THIS PRODUCT FROM. PLEASE VISIT www.creativecedardesigns.com OR CONTACT US DIRECTLY AT OUR OFFICE, 1-888-363-4967 WE WILL ANSWER YOUR QUESTIONS, OR HELP WITH WHAT YOU NEED. For more efficient service, please log onto our website at www.creativecedardesigns.com and fill out a request for missing or damaged parts. A completed product registration is also necessary for all warranty claims.
Dear Customer: Thank you for purchasing a Creative Cedar Designs Playcenter. We hope it will bring you and your children many years of safe and enjoyable fun. Creative Cedar Designs equipment is recommended for use by children 3 to 10 years of age. Creative Cedar Designs structures are not intended for public use. Creative Cedar Designs does not warranty any of its residential structures subjected to commercial use.
The instructions and owner’s manual for your new Playcenter should be read in its entirety before assembly, to minimize problems and safety issues. We recommend reading the owner’s manual thoroughly after you have identified all of the parts for your Playcenter as discussed in the Helpful Installations Hints section below. Positioning Your Play center 1. The Playcenter is designed to be installed on a level surface by an Adult with an Adult helper.
Helpful Installation Hints 1. Depending on your experience, assembly of this Play set should take approximately 6 to 12 hours after inventory of parts. Therefore, we recommend you set aside a full day for assembly. 2. Identify all of the parts for your Playcenter. Empty each box and lay out boards so you can see each part. Your instruction book will have detailed drawings that will make it easy for you to recognize individual parts. Keep all hardware and metal parts separate from wooden pieces. 3.
Suggested Playground Surfacing Playground equipment should never be placed on hard surfaces such as concrete or asphalt. Do not install loose fill surfacing over hard surfaces such as concrete or asphalt. Shredded bark mulch, wood chips, fine sand and fine gravel, are added as shock absorbing materials after assembly. If used properly these materials can absorb some of the impact of a child’s fall. All surface material should extend a minimum of 6 feet in all directions around the play area.
Operating Instructions: NOTE: Your children’s safety is our #1 concern. Observing the following statements and warnings reduces the likelihood of serious or fatal injury. Please review these safety rules regularly with your children. 1. This Playcenter is designed for the use of 6 occupants, who have a combined weight not exceeding 420 pounds, 4 occupants on the swing area, who have a combinedweight of 350 pounds , for a total unit cpacity of 10 occupants who who have a combined total weight of 770 pounds.
Maintenance Instructions: 1. Check all nuts and bolts twice monthly during the usage season and tighten as required. (But not so tight that you crack the wood) We recommend you check the swing beam and hardware every two weeks due to wood expansion and contraction. It is particularly important that this procedure be followed at the beginning of each season. 2. Remove plastic swing seats and take indoors or do not use when the temperature drops below 32 F. 3.
APPENDIX A Information on Playground Surfacing Materials: The following information is from the United States Consumer Product Safety Commission’s Information Sheet for playground surfacing material Also see the following website for additional information: https://www.cpsc.gov/PageFiles/122146/324.
Timber Valley Play S et Assembly Instructions WARNING: CHOKING HAZARD Unassembled parts may be a choking hazard to children 3 years and younger CAUTION: Adult Assembly Required. Hardware contains small pieces with sharp points. Keep parts out of the reach of children until assembled. Parts of this product can present dangers ifi mproperly assembled. CAUTION: The plastic bags that contain the hardware may present a choking hazard to small children.
Basic Setup Dimensions Place the set on level ground, not less than 6ft (1.83M) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines or electrical wires. 27'-7" SAFETY AREA SAFE HEIGHT 7'-9" 11'-10" 25'-7" Ht=15'-3" Ht=9'-3" 15'-19" Important Assembly Notes 1) While assembling unit, take time before and after each phase to make sure Fort is level. If fort is not level, assembly will be difficult and improper assembly may result.
Parts Identification Wood Components (8) WD3039 Roce Board-A 1×4×21 (2) WF3001 Sanbox board-A 1×6×54 (2) WF3018 Top Double Arch Board 1×6×54 (1) WQ3002a Upringt-A 3×4×78 3/4 (1) WF3019 Top Arch Board 1×6×31 (8) WD3040 Roce Board-B 1×4×21 (1) WQ3002b Upright-B 3×4×78 3/4 (1) WD3020 Top Brace 1×4×31 (1) WC3042 Roce Board-C 1×3×21 (2) WD3003 End Floor Support 5/4×4×54 (2) WF3022 Playhouse Arched Guardrail-A 1×6×54 (2) WF3004 Sandbox Board-B 1×6×52 13/16 (1) WQ3005a Upringt-C 3×4×89 5/16 (4) WD30
Parts Identification (2) GREEN ANGLE BRACKET (5") - M005 (2) GLIDER SUPPORT ASSEMBLY - A501 (8) COUNT BAG - CLIMBING ROCKS - B10LGR (2) 100° TRIANGLE PLATE - M100 Accessories (14) GREEN L-BRACKET - M003 (6) PLASTIC STAKES - P004 (4) SWING HANGER - M020 (2) PAIR - HAND GRIP - P002 (2) SWING SEAT W/ CHAIN ( PLASTIC ) - A101 12
Hardware Identification 1/4x31/2" Socket Pan-Head Bolt 2 1/4" Wood Screws a1 (10) e1 (4) #8DS3/4 1/4MT11/4 1/4x7/8" Socket Pan-Head Bolt 1 3/4" Wood Screws a2 (8) e2 (4) #6DS3/4 1/4MT11/4 1 1/8 " Wood Screws 5/16"×4 1/8" Socket Pan-Head Bolt a3 (428) #6DS3/4 e3 (8) 7/8" Wood Screws a4 (52) #6DS3/4 5/16"×3 1/2" Socket Pan-Head Bolt e4 (1) 5/16"×3 3/8" Socket Pan-Head Screws b1 (2) 5/16"×2 3/4" Socket Pan-Head Bolt e5 (8) 5/16"×1 5/8" Socket Pan-Head Screws b2 (68) 5/16"×2 1/2" Socket
Hardware Identification 5/16"×6 1/4" Hex Bolts 5/16HB6 f1 (2) 5/16"×5 3/4" Hex Bolts 5/16HB43/4 f2 (8) 0 5/16" x 4" Hex Bolts 5/16HB4 1/4" f3 (8) 1/2" 3/4" 5/16" Lock Nuts 5/16" Split Washers 5/16FWX25 LN5/16 g (18) 1" 5/16" Fender Washer k2 (161) m (4) 2" 5/16" T-nuts 5/16" Flat Washer 5/16FWX16 h (4) k3 (8) 5/16TN Allen Wrench 3/16" n (2) 3" 1/4" Flat Washers 3/8" Flat Washer 3/8FWX25 1/4FWX13 k4 (22) k1 (47) 4" 5" Measuring hardware It is very important that you get the
Quick Overview of Parts FRONT RIGHT 15
Quick Overview of Parts BACK 16 LEFT
TOWER ASSEMBLY Note: It is vital that the fort be level after this phase! STEP 1: * Insert all nut barrels "d1" into the uprights respectfully. /8" * Lay out WQ02a, WQ05b and WQ05a as shown. * Attach WD07 into the pre-drilled holes with bolt "e3". * Attach WD04 into the pre-drilled holes with wood screws "b2". 7 30 WD07 e3 k2 d1 e3 d k1 a1 WQ02a k2 WQ05b k1 WQ06a d1 WQ05a * Attach WD09 between WD07 and WD04 with wood screws "b2". * Attach both WC13 as shown.
TOWER ASSEMBLY Note: It is vital that the fort be level after this phase! STEP 2: * Insert all nut barrels "d1" into the uprights respectfully. * Lay out WQ06a, WQ06b and WQ02b as shown. * Attach WD07 into the pre-drilled holes with bolts "e3". * Attach WF04 into the pre-drilled holes with wood screws "b2". " /8 07 * Attach both WC13 as shown.
TOWER ASSEMBLY Note: It is vital that the fort be level after this phase! STEP 3: * Insert all nut barrels "d1" into the uprights respectfully. * Stand Right Wall from Step1 and Left Wall from Step2. * Attach both WF01 to form the front and back bottom of the tower with bolts "e6". * Attach both WD03 to form the front and back middle of the tower with bolts "e5".
TOWER ASSEMBLY Note: It is vital that the fort be level after this phase! STEP 4: * Attach both WD08 with wood screws "a2". * Install four "L" brackets (M003) with wood screws "c2".
TOWER ASSEMBLY Note: It is vital that the fort be level after this phase! STEP 5: * Lay WF15a, WF15b, WF16 in its rightful place as shown. * Lay all eleven WF14 in between to from the tower deck. * Once all slats are in place, make sure all slats are flush on the left and right side of the tower. * Once all slats are are flush secure slats with wood screw "a3". WD16 WD115b WD14 a3 WD15a ant I m p o rt ! e t No WD07 3 WD0 Make sure "a3" wood screws are going into the suport below.
TOWER ASSEMBLY Note: It is vital that the fort be level after this phase! STEP 6: * Insert all nut barrels "d1" into the uprights respectfully. * Attach WD23 and WD31 to WQ02a & b with wood screw "b2". * Attach WF22 to WQ02a & b (See diagram below). * From the inside deck, attach four WD24 to the right of the arch with wood screws "a3". * From the inside deck, attach one WD24 to the left of the arch with wood screws "a3".
TOWER ASSEMBLY STEP 7: * Attach WD33 and WF26 with wood screws "b2". * From the inside deck, attach WD30 to the right of the arch with wood screws "a3". * From the inside deck, attach seven WD24 to the right of WD30 side by side with no spaces in between with wood screws "a3".
TOWER ASSEMBLY STEP 8: * Insert nut barrel "d1" into the uprights respectfully. * Attach the WD23 and WD31 to the uprights with bolts "e6". * Attach WF22 to the uprights with wood screws "b2". * From the inside deck, attach both WD25b, one on each side of the arch with wood screws "a3". * From the inside deck, attach five WD24 to the right of the WD25b, also on the right of the arch. (There should be no spaces).
TOWER ASSEMBLY STEP 9: * Attach both WD23 with wood screws "b2". * From the inside of the playhouse, attach five WD24 followed by one WD25a to the right ( There should be no spaces).
TOWER ASSEMBLY STEP10 : * Attach WD31 with wood screws "b2" from the front . * From the inside of the play house, attach WD25c with wood screws "a3". * Install six L brackets "M003" as shown.
TOWER ASSEMBLY Note: It is vital that the fort be level after this phase! STEP11 : * From the inside of the playhouse, place both WQ32 into its place so you can see the correct orientation. * Insert two nut barrels "d1" into both WQ32. * Attach both WQ32 extensions into uprights (WQ06a & WQ06b) with bolt "e8". * From the inside of the playhouse, insert the two remaining nut barrels "d1" as shown. * Attach both WF18 with bolts"e6" and wood screws "b2" from the front and back of the playhouse.
TOWER ASSEMBLY STEP12 : * Attach four WF10 with wood screws "b2". * Attach both WF11 with wood screws "a3".
TOWER ASSEMBLY Note: It is vital that the fort be level after this phase! STEP13 : * Insert four T-nuts "h" into the backside of WF29 for use in Step22. * Attach WF29 with bolts "e5" and wood screws "b2". * Attach WF27 and WD09 with wood screws "b2". * From the inside of the playhouse, attach seven WC17b and one WC17a with wood screws "a3" * From the inside of the playhouse, attach three WD24 with wood screws "a3".
ROCKWALL ASSEMBLY e STEP14 : * Create the rockwall by attaching two WD38 with seventeen rockwall boards. Note the orientation of the holes. * Suggestion: Line up all the rockwall boards and make sure, they are all flush before securing with wood screws "a3" . * From the back of assembled rock wall insert nut barrel "d2". * Install the climbing rocks ( See detail diagram below ).
ROCKWALL ASSEMBLY STEP15 : * Attach both L brackets "M003" to Rockwall (See detailed diagram below). * Attach Rockwall with installed L brackets "M003" to the playset's back wall.
LADDER ASSEMBLY STEP16 : * Create the ladder by attaching four WD36 in between WD34 and WD35. They should fit comfortably inside the notches and securing with wood screws "a3". * Attach WD37 to ladder with wood screws "a3". * Attach ladder to the playset's left wall using both L bracket "M003" and wood screws "c1".
ROOF ASSEMBLY STEP17 : * Create the short side of the roof by laying out one WF55 and four WF54, and securing WB52 to it with wood screws "a3". * Attach both WD44 onto the short side of the roof, one on either end with wood screws "a3". * Create the long side of the roof by laying out one WF55 and eight WF54, and securing WB53 to it with wood screws "a3". * Attach both WD43 onto the long side of the roof, one on either end with wood screws "a3".
ROOF ASSEMBLY STEP18 : * Create one sunburst for the front and one for the back, with wood screws "a4" (See diagrams below). * Secure both sunburts to the roof from the inside with wood screws "a4". * From the inside, secure one WC46 to longe side of each sunburst with wood screws "a4". 11 11/1 ant I m p o rt ! e t No 6'' * Sunbursts should be mirror images! * Rays of sunburts should be spread out evenly. Interior views of sunburst a4 WC46 WC48 ant I m p o rt ! e t No * Use only 6 "a4" wood screws.
ROOF ASSEMBLY STEP19 : * Mount the roof to the playhouse. * Secure WD25a, WD26b and WD25c with wood screws "a3". * Secure WC46 with wood screws "a4". WC46 a3 a3 a3 WC46 a3 a4 a3 a3 a3 a4 a4 a3 WD25a WD25c WD25b Inside view of front Inside view of back ant I m p o rt ! e t o N The shorter roof side gets mounted to the taller post. The longer roof side gets mounted to the shorter post.
ROOF ASSEMBLY STEP20 : * Secure the roof with wood screw "b2", three time in the front and three times in the back.
HAND GRIP ATTACHMENT STEP21 : * Insert nut barrels "d3" into the upright respectfully. * Attach back wall's hand grips with bolts "e2". * Attach left wall's hand grips with bolts "e1".
SWING BEAM ASSEMBLY STEP22 : * Prepare swing beam WZ59 by mounting two triangle plates "M100" and two angle brackets "M005" with bolts "f3". * Insert nut barrels "d1" into both WQ56 and WU58. * Create swing beam leg with both WQ56, WQ57 and WU58 with bolts "e4", "e7" and wood screws "b1". * Attach the swing beam WZ59 to the prepared swing beam leg. * Attach the completed swing beam to the playset's right wall with bolts "e9".
SWING BEAM ASSEMBLY S T E P 23 : * Install both glider supports "A501" with bolts "f3". * Install four swing hangers "M020" with bolts "f2". * Build two person glider with both P206 and P205 ( See diagram ). * Hang the completed glider to glider suport and fasten. * Hang both swings A101 to the swing hangers and fasten.
SLIDE ATTACHMENT STEP24 : * Slide SOLD SEPERATLY. Please follow manufacturer's instructions. * If no instructions are provided, please use the following instructions as GUIDELINE ONLY.
ACHORING STEP25 : * Place six stakes in to the ground next to the playset as shown. e * Secure the stakes with wood screws "a1" ( See diagram ). Note: Failure to use stakes can void warranty & cause injury. Final Step: Double check and make sure every bolt, screw and nut is tight. Make sure every board is secure. Make sure the fort is level and enjoy your playset.
LIMITED WARRANTY Creative Cedar Design (CCD) offers many fun, interactive, and safe play sets. We only guarantee the original purchaser that this product is free of defects for 30 days from the date of purchase. The product registration card, along with a dated purchase receipt, must be returned to CCD within 30 days. Within a 30 day period, CCD will repair or replace, at our option, defective merchandise free of charge, provided that the defective part is a manufacturer’s defect and not seasonal check.
Warranty claim procedure If you are confident that your play system has been installed and maintained properly, and you have a warranty claim, proceed with the following steps: 1. We will need copy of your proof of purchase (Vendor sales receipt only.) 2. We require a brief written description of the warranty issue. 3. Photos of warranted parts and of the entire play system. If any of the above steps are not completed, there may be delays in the completion of your claim, or possibly warranty cancellation.
PRODUCT REGISTRATION CARD Please complete this Product Registration Card along with a copy of the receipt and return to Creative Cedar Designs, within 30 days of original purchase in order to validate time of purchase for warranty. Or register at www.creativecedardesigns.
PRODUCT REGISTRATION CARD Please complete this Product Registration Card along with a copy of the receipt and return to Creative Cedar Designs, within 30 days of original purchase in order to validate time of purchase for warranty. FOLD HERE Place Stamp Here Creative Cedar Designs 2700 Riverside Dr.
