Mountain View 3430 ASSEMBLY INSTRUCTIONS Creative Cedar Designs • PO Box 4901 • Chattanooga, TN 37405 Visit our web site at: www.Creativecedardesigns.
ATTENTION: READ THIS BEFORE USE OF YOUR PLAYSET OR ACCESSORY: Observing the following statements and warnings reduces the likelihood of serious or fatal injury. This product has been designed for single family home/residential use only and is not intended for use in any public setting. Placement in public settings constitutes misuse of this product. Play Safe Installation Checklist: → No children are to be allowed to use the equipment until it is properly installed.
LIMITED WARRANTY Creative Cedar Design (CCD) offers many fun, interactive, and safe play sets. We only guarantee the original purchaser that this product is free of defects for 30 days from the date of purchase. The product registration card, along with a dated purchase receipt, must be returned to CCD within 30 days. Within a 30-day period, CCD will repair or replace, at our option, defective merchandise free of charge, provided that the defective part is a manufacturer’s defect and not seasonal check.
DIMENSIONS MINIMUM USE ZONE FOR PLAY EQUIPMENT SHALL EXTEND NO LESS THAN 72” FROM ALL SIDES OF THE PLAY STRUCTURE. SWING USE ZONE EXTENDS NO LESS THAN 158” SWINGS MUST HAVE A MINIMUM OF 8” ABOVE THE PROTECTIVE SURFACING.
TOOLS REQUIRED DRILL 9/16”, 1/2” & 7/16” SOCKET & WRENCH HAMMER ADJUSTABLE WRENCH TAPE MEASURE PHILLIPS BIT TORX T-20 BIT SQUARE BIT CARPENTER SQUARE SAFETY GLASSES INCLUDED HARDWARE 5
INCLUDED HARDWARE CONT.
INCLUDED COMPONENTS (2) A-Frame Bracket M100 (3) 2 Count Std Swing Hanger BP 002 (2) Swing Beam Mount M005 (1) 6pk Monkey Bars BP 004-G w/ Hardware (1 Pair) Safety Handles BP 007-Y w/ Hardware (1) Binocular BP 006-Y w/ Hardware (2) Standard Swing Seat (1) Steering Wheel BP 010-G BP 008-G w/ Hardware (1) 4pk Anchor Kit BP 001-B w/ Hardware (2) 4pk Climbing Rocks BP 011-GYBR w/ Hardware Mountain View 3430 ASSEMBLY INSTRUCTIONS CreativeCedarDesigns.
BOARD LIST 8
STEP 1 Rockwall Post Assembly WM701 POST T-NUT T-NUT T-NUT WM715 DECK SUPPORT T-NUT 5/16-18 T-Nut (x3) T-NUT T-NUT WM707 DECK SUPPORT T-NUT T-NUT T-NUT WM701 POST 3/8-16 T-Nut (x16) 1. Insert T-Nut(s) into Post(s) and supports as shown. NOTE the hole orientation.
STEP 2 Rockwall Post Assembly Check to make sure structure is square WM706 RAILING - RW 3-3/4” Bolt TIP: Hand tighten bolts, square structure, install screws then tighten bolts. WM715 DECK SUPPORT WM707 DECK SUPPORT 4-3/4” Bolt 3-3/4” Bolt WM725 BASE 2” Deck Screw (x8) 3/8-16 x 3-3/4” Hex Bolt (x4) 3/8-16 x 4-3/4” Hex Bolt (x2) 3/8 Lock Washer (x6) 3/8 Washer (x6) 1. Attach Support boards as shown. NOTE the hole orientation and T-Nut locations.
STEP 3 Swing Beam Post Assembly WM703 POST-SB T-NUT T-NUT WM707 DECK SUPPORT T-NUT T-NUT T-NUT T-NUT WM741 SWING BEAM MOUNT T-NUT 5/16-18 T-Nut (x4) T-NUT T-NUT WM703 POST-SB 3/8-16 T-Nut (x14) 1. Insert T-Nut(s) into Post(s) and supports as shown. NOTE the hole orientation.
STEP 4 Swing Beam Post Assembly 4” Bolt(s) WM741 SWING BEAM MOUNT Check to make sure structure is square 3-3/4” Bolt WM705 RAILING TIP: Hand tighten bolts, square structure, install screws then tighten bolts. WM707 DECK SUPPORT WM712 BARRIER SUPPORT 4-3/4” Bolt 2” Deck Screw (x12) WM724 BASE 3/8-16 x 3-3/4” Hex Bolt (x8) 3-3/4” Bolt 3/8-16 x 4” Hex Bolt (x4) 3/8-16 x 4-3/4” Hex Bolt (x2) 3/8 Lock Washer (x14) 3/8 Washer (x14) 1. Attach Support boards as shown.
STEP 5 T-NUT TIP: Hand tighten bolts, square structure, install screws then tighten bolts. WM728 ROOF SUPPORT Check to make sure structure is square T-NUT WM728 ROOF SUPPORT T-NUT WM705 RAILING T-NUT WM725 BASE WM713 RAILING WM712 DECK SUPPORT WM725 BASE WM712 DECK SUPPORT 2” Deck Screw (x12) 3/8-16 x 3-3/4” Hex Bolt (x16) 3/8 Lock Washer (x16) 3/8 Washer (x16) 1. Attach Support boards as shown. NOTE the hole orientation and T-Nut Locations.
STEP 6 TIP: Hand tighten bolts, square structure, install screws then tighten bolts. Check to make sure structure is square 2” Screw(s) (8) WM740 ANGLED DECK SUPPORT 2-1/2” Screw 2” Screw 2” Screw 3” Screw WM708 TOWER SUPPORT 2” Screw(s) 2” Deck Screw (x28) 2-1/2” Deck Screw (x8) 3” Deck Screw (x1) 1. Attach Deck Support boards as shown. NOTE hold boards below deck support.
STEP 7 WM771 DECK - SLIDE 1-1/2” Screw(s) WM732 DECK - MB 1-3/8” Screw(s) from top of deck WM718 CENTER DECK SUPPORT (11) WM733 DECK (2) WM768 SLIDE SUPPORT T-Nut on bottom Underdeck View 1-3/8” Screw(s) 1-3/8” Deck Screw (x23) 1/4-20 T-Nut (x2) 1-1/2” Deck Screw (x52) 1. Attach deck boards as shown. NOTE align the center mounting hole of the slide support and deck.
STEP 8 WM705 RAILING WM739 BARRIER SUPPORT LH SLIDE WM721 BARRIER SUPPORT RH SLIDE 2” Deck Screw (x4) 3/8-16 x 3-3/4” Hex Bolt (x4) 3/8 Lock Washer (x4) 3/8 Washer (x4) 1. Attach barrier support boards as shown. Note the board(s) orientation.
STEP 9 (3) WM736 BARRIER BOARD (8) WM736 BARRIER BOARD 3/4” gap between posts 1-3/8” gap between boards 1-1/2” Deck Screw (x44) 1. Attach Barrier boards as shown.
STEP 10 (4) WM736 BARRIER BOARD no gap against posts flush to end of barrier support 1-1/2” Deck Screw (x8) 1. Attach Barrier boards as shown.
STEP 11 STEP 11A (2) WM729 ROOF A-FRAME x2 WM731 ROOF TARP END WM730 ROOF RIDGE FLUSH STEP 11B STEP 11C 2” Deck Screw (x16) 3/8-16 x 2” Hex Bolt (x4) 3/8 Lock Washer (x4) 1. Assemble two Roof A-Frames and attach as shown. 2.
STEP 12 WM742 GABLE CTR (2) WM744 GABLE ANGLE (2) WM743 GABLE SIDE x2 WM749 GABLE SUPPORT 1-3/4” Deck Screw (x46) 1. Attach Gable boards as shown.
STEP 13 T-NUT WM772 LADDER HE T-NUT WM711 RW/LDR RHGIT T-NUT WM710 RW/LDR CENTER WM709 RW/LDR LEFT 2” Deck Screw (x20) 5/16-18 T-Nut (x3) 1. Install T-Nuts as shown. NOTE the hole orientation for each board. 2. Attach Ladder steps and HE board as shown.
STEP 14 (3) M002 BRACKET 1-1/4” Bolt WM727 LADDER SUPPORT 1-3/4” Bolt 5/16-18 x 1-1/4” Hex Bolt (x3) 5/16-18 x 1-3/4” Hex Bolt (x3) 5/16 Washer (x6) 2” Deck Screw (x4) 5/16 Lock Washer (x6) 1. Attach Brackets to deck support, then attach the Ladder and Rockwall support boards as shown NOTE ladder board(s) orientation 2.
STEP 15 (5) WM734 ROCKWALL (2) WM722 ROCKWALL - CENTER (6) WM737 ROCKWALL - SIDE WM723 ROCKWALL - BOTTOM 2” Deck Screw (x56) 1.
STEP 16 Swing Beam Assembly 5/16-18 T-Nut (x6) LA251 SWING BEAM 1 2 3 TIP: Slide a screwdriver thru the Hanger hook to help tighten it into the T-Nut 4 5 1-1/4” Deck Screw (x24) 1. Attach Swing Hangers to swing beam as shown. Note plate & swing hanger must be tight against bottom of swing beam prior to step 5.
STEP 17 Swing Beam Assembly (2) M005 BRACKET 5/16-18 x 4” Hex Bolt (x2) 5/16 Washer (x4) 5/16-18 Lock Nut (x2) 1. Attach Brackets to swing beam as shown.
STEP 18 A-Frame Assembly LG252 SWING BEAM A-FRAME LD254 SWING BEAM SUPPORT LG252 SWING BEAM A-FRAME LG253 SWING BEAM BASE 5/16-18 x 3-1/4” Hex Bolt (x2) x3 5/16-18 x 3-1/2” Lag Screw (x2) 5/16-18 x 4-1/2” Hex Bolt (x1) 5/16 Washer (x8) 5/16-18 Lock Nut (x3) 1. Assemble A-Frame assembly as shown.
STEP 19 (2) M100 A-FRAME BRACKET 5/16-18 x 4” Hex Bolt (x2) 5/16 Washer (x4) 1. Attach A-Frame brackets as shown.
STEP 20 Swing Beam Assembly A-Frame Assembly 5/16-18 x 4” Hex Bolt (x2) 5/16 Washer (x4) 1. Attach Swing Beam assembly to A-Frame assembly as shown.
STEP 21 5/16-18 x 1-1/2” Hex Bolt (x4) 5/16 Washer (x4) 5/16 Lock Washer (x4) 1. Attach Swing Beam Assembly to tower as shown.
STEP 22 TOP RUNG ASSEMBLY T-NUT WM773 MONKEY BAR TOP LH WM745 MONKEY BAR TOP RH T-NUT (6) PT 401 MONKEY BAR 22” 3/8-16 T-Nut (x6) 1. Insert T-Nut(s) into supports as shown. NOTE the hole orientation and T-Nut locations. 2. Attach Monkey Bar(s) with hardware from accessory kit as shown.
STEP 23 LADDER ASSEMBLY T-NUT T-NUT WM767 MONKEY BAR LDH LH WM746 MONKEY BAR LDR RH T-NUT (2) WM748 MONEKY BAR ANGLE SUPPORT T-NUT T-NUT (3) WM770 MONEKY BAR STEP 3-3/4” Bolt 2-3/4” Bolt WM747 MONKEY BAR BASE 4-3/4” Bolt 2” Deck Screw (x12) 3/8-16 x 2-3/4” Hex Bolt (x2) 3/8-16 x 3-3/4” Hex Bolt (x2) 3/8-16 x 4-3/4” Hex Bolt (x2) 3/8 Lock Washer (x10) 3/8 Washer (x10) 3/8-16 T-Nut (x10) 1. Insert T-Nut(s) into supports as shown. NOTE the hole orientation and T-Nut locations. 2.
STEP 24 TOP RUNG ASSEMBLY (2) 2023 BRACKET 2-3/4” Bolt 1-3/4” Bolt LADDER ASSEMBLY 3/8-16 x 1-3/4” Hex Bolt (x6) 3/8-16 x 2-3/4” Hex Bolt (x2) 3/8 Lock Washer (x8) 3/8 Washer (x8) 1. Attach Brackets to Top Run Assembly as shown. NOTE orientation of bracket holes 2.
STEP 25 (2) 2084 BRACKET 1-3/4” Bolt 1-1/4” Bolt 3/8-16 x 1-1/4” Hex Bolt (x2) 3/8-16 x 1-3/4” Hex Bolt (x2) 3/8 Lock Washer (x4) 1. Attach Brackets to railing as shown. 2. Attach Monkey Bar assembly to brackets as shown.
STEP 26 1/4-20 T-Nut Climbing Rock 1/4” Lock Washer 8mm Washer 1/4”-20 x 2-1/4 Hex Head Bolt 1. Attach Climbing Rocks as shown. 2. Make sure Climbing Rocks and rock wall connections are fully secure before use.
STEP 27 CLIMBING ROPE 1. Attach Climbing Rope as shown.
STEP 28 (2) SAFETY HANDLES 1.
STEP 29 TARP FLUSH 3/16 Fender Washer (x6) #8 x 3/4” Pan Screw (x6) 1. Lay tarp over both Roof End and Roof Ridge as shown. 2. Wrap one end of the tarp under and around a Roof End board, hold flush as shown and secure with (3) washers & screws per end. 3. Pull tarp taught and secure other end.
STEP 30 BINOCULARS 1. Attach Binoculars per accessory plan.
STEP 31 STEERING WHEEL 1. Drill a 5/16” hole at the location shown and attach Steering Wheel per accessory plan.
STEP 32 1/4-20 Screw, Lock & Flat washer Outer Holes 1” Truss Screw Center Hole 1-1/4” Deck Screws 2” Grade WM774 SLIDE STAKE 1” Truss Screw (x1) 1/4-20 x 2” Button Head Bolt (x2) 1/4 Lock Washer (x2) 1/4 Washer (x2) 1-1/4” Deck Screw (x2) 1. Attach slide using (2) 1/4-20 Screw, Lock Washer & Flat washer on the outside slide holes. 2. Install (1) Truss screw into center slide hole. 3. Istall Slide Stake and screws as shown.
STEP 33 Standard Swing Seats NOTE: Swing Hanger must be crimped close. 1. Assemble Standard Swing Seat(s) per accessory plan and mount to swing hangers as shown.
STEP 34 Ring-Trap NOTE: Swing Hanger must be crimped close. 1. Assemble Ring-Trap per accessory plan and mount to swing hangers as shown.
STEP 35 5/16” Washer Fold up 1-1/2” Lag Screw Anchor-It Strap Anchor-It 1. Place swing set in final location and mount Anchor(s) at locations circled above. 2. Twist the Anchor into the ground until only the loop is exposed. 3. Place Anchor strap thru loop, fold the ends together and attach to the unit as shown. Note: Keep as little play as possible using any of the holes in the strap that work best.
STEP 36 CreativeCedarDesigns.com 1/2” Pan Screw (x2) 1. Attach ID Tag as shown.
CCD 3430 888-363-4967 Got Questions? We’ve got answers! Call our Customer Support Representatives Available Monday - Friday, 9am - 4pm (EST) Technical Support from experienced Customer Service Representatives who have actually built a swing set themselves. Visit our web site at: www.Creativecedardesigns.com © Creative Cedar Designs 2020 10.27.
