Bridge option below sold sepeately Sequoia Model: 3200 Owners of the Jungle Fun, Model 3201 Follow these plans thru phase 23, then proceed to the bridge instructions located in box 7. For FSC certified products look for the FSC label SGS-COC-005310 1996 Forest Stewardship Council A.C.
Thank you for purchasing a Creative Cedar Designs Playcenter. We hope it will bring you and your children many years of safe and enjoyable backyard fun.
STOP…PLEASE READ!! IF YOU HAVE ANY QUESTION OR ARE MISSING A PART, PLEASE DO NOT CONTACT THE RETAILER THAT YOU PURCHASED THIS PRODUCT FROM. PLEASE VISIT www.creativecedardesigns.com OR CONTACT US DIRECTLY AT OUR OFFICE, 1-888-363-4967 WE WILL ANSWER YOUR QUESTIONS, OR HELP WITH WHAT YOU NEED. For more efficient service, please log onto our website at www.creativecedardesigns.com and fill out a request for missing or damaged parts. A completed product registration is also necessary for all warranty claims.
Dear Customer: Thank you for purchasing a Creative Cedar Designs Playcenter. We hope it will bring you and your children many years of safe and enjoyable fun. Creative Cedar Designs equipment is recommended for use by children 3 to 10 years of age. Creative Cedar Designs structures are not intended for public use. Creative Cedar Designs does not warranty any of its residential structures subjected to commercial use.
The instructions and owner’s manual for your new Playcenter should be read in its entirety before assembly, to minimize problems and safety issues. We recommend reading the owner’s manual thoroughly after you have identified all of the parts for your Playcenter as discussed in the Helpful Installations Hints section below. Positioning Your Play center 1. The Playcenter is designed to be installed on a level surface by an Adult with an Adult helper.
Helpful Installation Hints 1. Depending on your experience, assembly of this Play set should take approximatley 6 to 12 hours after inventory of parts. 2. Identify all of the parts for your Playcenter. Empty each box and lay out boards so you can see each part. Your instruction book will have detailed drawings that will make it easy for you to recognize individual parts. Keep all hardware and metal parts separate from wooden pieces. 3.
Suggested Playground Surfacing Playground equipment should never be placed on hard surfaces such as concrete or asphalt. Do not install loose fill surfacing over hard surfaces such as concrete or asphalt. Shredded bark mulch, wood chips, fine sand and fine gravel, are added as shock absorbing materials after assembly. If used properly these materials can absorb some of the impact of a child’s fall. All surface material should extend a minimum of 6 feet in all directions around the play area.
Operating Instructions: NOTE: Your children’s safety is our #1 concern. Observing the following statements and warnings reduces the likelihood of serious or fatal injury. Please review these safety rules regularly with your children. 1.
Maintenance Instructions: 1. Check all nuts and bolts twice monthly during the usage season and tighten as required. (But not so tight that you crack the wood) We recommend you check the swing beam and hardware every two weeks due to wood expansion and contraction. It is particularly important that this procedure be followed at the beginning of each season. 2. Remove plastic swing seats and take indoors or do not use when the temperature drops below 32 F. 3.
APPENDIX A Information on Playground Surfacing Materials: The following information is from the United States Consumer Product Safety Commission’s Information Sheet for playground surfacing material Also see the following website for additional information: https://www.cpsc.gov/PageFiles/122146/324.pdf . X3. CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS11 X3.1 The U.S.
The Sequoia Assembly Instructions WARNING: CHOKING HAZARD Unassembled parts may be a choking hazard to children 3 years and younger. The plastic bags that contain the hardware may present a choking hazard to small children. Please keep these bags and all plastic bags out of the reach of children. Do no allow children to play with them and dispose of them immediately when empty. CAUTION: Adult Assembly Required 9 Hardware contains small pieces with sharp points.
Basic Setup Dimensions Place the set on level ground, not less than 6ft (1.83M) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines or electrical wires. SAFETY AREA 16'-11" [5.1M] Ht. = 16'-7" [5M] 28'-11" [8.8M] SAFE HEIGHT Ht. = 10'-7" [3.2M] 21'-3" [6.5M] 33'-3" [10.1M] Important Assembly Notes 1) While assembling unit, take time before and after each phase to make sure Fort is level.
Parts Identification Wood Components (2) 1 X 5 5/16 X 65 SAND BOX BOARD - LK212 (1) 3 5/16 X 5 5/16 X 89 1/2 SWING BEAM - LA251 (2) 3 5/16 X 2 11/16 X 90 1/2 UPRIGHT - LD201 (2) 1 X 5 5/16 X 44 3/4 SAND BOX BOARD - LK223 (2) 3 5/16 X 2 11/16 X 90 1/2 UPRIGHT - LD202 (2) 1 X 5 5/16 X 44 3/4 SLIDE ARCH RAIL - LK224 19 13/16 (4) 3 5/16 X 2 11/16 X 90 1/2 UPRIGHT - LD203 (2) 1 X 5 5/16 X 44 3/4 LAD./ROCK W.
Parts Identification (4) 1 X 3 1/2 X 11 WALL RAIL - LM226 Wood Components (5) 11/16 X 3 1/2 X 31 1/2 ROCK BRD.
Parts Identification (1 PAIR) GLIDER BRACKET BP 020 w/ HARDWARE (16) GREEN L-BRACKET (SMALL) M002 (2) TARP (GREEN) P005 w/ HARDWARE (2) GREEN 4 HOLE TRIANGLE PLATE M100 (2) CLIMBING ROCK 4-PACK BP011-GYBR w/ HARDWARE (8) GREEN L-BRACKET M003 CreativeCedarDesigns.
Hardware Identification 5/16" x 4 3/4" Hex Bolts 5/16HB43/4 (4) 0 1/4" 5/16" x 4 1/4" Hex Bolts 5/16HB41/4 1/2" (4) 3/4" 5/16" x 4" Hex Bolts 1" 5/16HB4 (10) 5/16" x 3 5/8" Hex Bolts 5/16HB33/4 5/16" x 2 3/4" Hex Bolts 5/16HB23/4 2" (64) (3) 3" 5/16" x 2 1/4" Hex Bolts 5/16HB21/4 (2) 4" 5/16" x 1 1/4" Hex Bolts (4) 5/16HB11/4 5" 5/16" x 1" Hex Bolts (12) 5/16HB1 5/16" x 3 1/2" Lag Screws 5/16LS31/2 6" (2) 5/16" x 2 1/2" Lag Screws 5/16LS21/2 ( 60) 14
Hardware Identification 2 1/2" Deck Screws #8DS2 1/2 (110) 5/16" Lock Nuts 1 3/4" Deck Screws 5/16" T-nuts LN5/16 #8DS13/4 ( 98 ) (12) (452) 5/16TN 11/8" Deck Screws #8DS11/8 (274) 5/16" Split Washers 5/16SW 1” Truss Head Screw (106) (16) Fender Washer 5/16FW8X27 5/16" Flat Washers 3/4" Tapping Screws 5/16FWX20 (16) (170) (18) #14TS3/4 5/16" x 4 1/2" Hex Head Bolt 5/16PH41/2 (1) 5/16" x 3 1/4" Hex Head Bolt 5/16PH31/4 (2) Measuring Hardware It is very important that you get t
LM215 LK212 LD203 LD203 LK212 LK223 LD202 LM283 LR282 LR282 LF281 LM219 LM210 LM220 LA251 LM226 LM219 LR240 LD201 LM214 LD254 LG252 LG253 LM214 16 LR240 LM210 LN204 LD203 Quick Overview of Parts
Quick Overview of Parts LR243 LS112 LR243 LM226 LM213 LM227 LR285 LR282 LR242 LR285 LR243 LS112 LR235 LD280 LM216 LM288 LK287 LR282 LR282 LM231 LM211 LR296 LM221 LR295 LR294 LH272 LR240 LR275 LM222 LD280 LR242 LH271 LR242 LM216 LH270 LJ273 LK224 LR243 LM290 LM291 TOWER 'B' LM215 LM213 LR293 LM226 LM227 LM213 LF250 TOWER 'B' LS113 BRIDGE LM226 LR242 LM227 LR242 LR282 LM227 LR242 TOWER 'A' LM226 TOWER 'A' LK224 LR235 LR234 LR243 LM227 LK225 LM230 LR262
Phase Hardware TOWER 'A' ASSEMBLY Phase 1: Fender Washer 5/16" Split Washers 5/16" x 3 5/8" Hex Bolts (16) (16) (24) 2 1/2" Lag Screws (8) (26) 5/16" T-nuts Phase Par (2) 3 5/16 X 2 11/16 X 90 1/2 UPRIGHT - LD201 (2) 3 5/16 X 2 11/16 X 90 1/2 UPRIGHT - LD202 (1)1 X 3 1/ 2 X 44 3/4 END FLOOR SUPP. - LM219 (3)1 X 3 1/2 X 65 GB / FLOOR JOIST - LM210 Note: It is vital that the fort be level after this phase! (1) 1 X 3 1/2 X 65 FLOOR JOIST - LM211 (1) 1 X 3 1/2 X 44 3/4 (LAD) END FLOOR SUPP.
Phase Hardware TOWER 'B' ASSEMBLY Phase 2: Fender Washer 5/16" Split Washers 5/16" x 3 5/8" Hex Bolts (16) (16) (28) 2 1/2" Lag Screws (12) (22) 5/16" T-nuts Phase Parts (4) 3 5/16 X 2 11/16 X 90 1/2 UPRIGHT - LD203 (2) 1 X 5 1/2 X 65 SANDBOX BOARD - LK212 (2) 1 X 5 5/16 X 44 3/4 SANDBOX BOARD - LK223 (1) 1 X 3 1/2 X 65 GB / FLOOR JOIST - LM210 Note: It is vital that the fort be level after this phase! (1) 1 X 3 1/2 X 65 FLOOR JOIST - LM211 (1) 1 X 3 1/2 X 44 3/4 (RW) END FLOOR SUPP.
Phase 3: BRIDGE UPRIGHTS & CROSS BRACES Phase Hardware 5/16" x 3 5/8" Hex Bolts Fender Washer 5/16" Split Washers (32) (32) (32) (24) USE A STEP LADDER FOR SAFETY! 5/16" T-nuts Phase Parts (4) 3 5/16 X 2 11/16 X 51 5/16 BRIDGE UPRIGHT - LD280 (4) 1 X 3 1/2 X 33 3/16 TARP CROSS BRACE - LM216 (2)1 X 3 1/2 X 90 TARP CROSS BRACE - LM215 STEP 1: INSERT (4) T-NUTS INTO BACKSIDE OF ‘LM216’ NOTE HOLE ORIENTATION STEP 2: INSERT (4) T-NUTS INTO BACKSIDE OF ‘LM215’ NOTE HOLE ORIENTATION LD280 2X 2X
Phase 4: BRIDGE ASSEMBLY & INSTALLATION 1" Truss Head Screw (4) Phase Hardware Fender Washer 5/16" Split Washers (4) (8) 5/16" x 4 3/4" Hex Bolts (4) (4) 5/16" T-nuts Phase Parts (2) 1 3/8 X 5 5/16 X 64 11/16 BRIDGE JOIST - LF281 (4) GREEN L-BRACKET (SMALL) M002 FENDER WASHER TRUSS HEAD SCREW FLOOR JOIST T-NUT BOLT SPLIT WASHER BRIDGE UPRIGHT FENDER WASHER BRIDGE JOIST TYPICAL DETAIL TOWER 'B' TOWER 'A' 21
Phase 5: CENTER FLOOR BRACE & PICNIC SUPPORT RAILS Phase Hardware 5/16” Split Washer (16) (4) (8) ( 16) 5/16” x 2 1/2” Lag Screws (8) Fender Washer 1” Truss Head Screw 2 1/2” Deck Screws 5/16” x 1” Hex Bolts 5/16” T-Nut ( 4) (4) Phase Parts (2) 1 x 3 1/2 x 65 CENTER FLOOR SUPPORT - LM214 (4) GREEN L-BRACKET (SMALL) M002 (4) 1 x 3 1/2 x 65 TABLE/BENCH SUPPORT - LM291 TRUSS HEAD SCREW 1/8” PRE-DRILL HOLES FOR ALL LAG SCREWS CENTER FLOOR SUPPORT MOUNTING DETAIL (4X) DECK SCREW FENDER WAS
Phase 6: Phase Hardware ROCKWALL ASSEMBLY PLEASE REFER TO ACCESSORY PLAN FOR INSTALLATION HARDWARE 1 3/4" Deck Screws (76) (19) 1 1/8" Deck Screws Phase Parts (1) 2 X 2 11/16 X 67 13/16 ROCKWALL RAIL LEFT - LH260 (1) 2 X 2 11/16 X 67 13/16 ROCKWALL RAIL RIGHT - LH261 (10) 11/16 X 3 1/2 X 31 1/2 ROCKWALL BRD. - LR262 (4) 11/16 x 3 1/2 x 31 1/2 ROCK BRD - LR263 (1) 11/16 X 3 1/2 X 66 1/4 ROCKWALL BRACE - LR265 (5) 11/16 X 3 1/2 X 31 1/2 ROCK BRD.
Phase 7: RUNG / CHAIN LADDER ASSEMBLY Phase Hardware 2 1/2" Deck Screws (14) Phase Parts (1) 2 X 2 11/16 X 67 13/16 LADDER RAIL RIGHT - LH270 (1) 2 X 2 11/16 X 67 13/16 LADDER MIDDLE RAIL - LH271 (1) 2 X 2 11/16 X 67 13/16 LADDER RAIL LEFT - LH272 (5) Ø1 1/8 X 13 3/4 LADDER RUNG - LJ273 (1)5/8X 3 1/2 X 15 3/4 LADDER SAFETY SLAT - LR274 (1) GREEN CHAIN LADDER - M010 153 4 LH271 STEP 1: LJ273 STEP 2: 1 34 1/16” PRE-DRILL HOLES INTO ‘LJ273’ LADDER RUNG(S) 2 1/2 DECK SCREWS 2 1/2" DECK SCREW LR27
Phase 8: ROCKWALL & LADDER ATTACHMENT Phase Hardware 5/16" x 1" Hex Bolts 5/16" x 2 3/4" Hex Bolts (3) (8) 5/16" Flat Washers (16) 5/16" Split Washers 5/16" x 2 1/4" Hex Bolts (2) 1 3/4" Deck Screws (4) 5/16" Lock Nuts (10) (4) 5/16" T-nuts (3) Phase Parts T-NUT (1) 5/8 X 35/16 X 211/4 CHAIN LADDER SAFETY SLAT - LR275 ROCKWALL BRACKETS (8) GREEN L-BRACKET (SMALL) - M002 5/16" FLAT WASHER LADDER BRACKETS 2 1/4" HEX BOLT LOCK NUT SPLIT WASHER 5/16" FLAT WASHER 2 3/4” HEX BOLT 5/16" FLAT
Phase 9: TOWER 'A' TABLE & BENCHES Phase Hardware 1 3/4" Deck Screws (36) (39) 1 1/8" Deck Screws STEP 1: Phase Parts (4) 11/16 X 2 9/16 X 35 9/16 PICNIC ANGLE LEGS - LR293 1 1/8” DECK SCREW 2 - BENCHES REQ’D. (1) 11/16 X 3 1/2 X 15 TABLE BRACE - LR297 LR298 (9) 1 X 3 1/2 X 39 3/8 TABLE/BENCH BRD.
Phase 10: SANDBOX SEATS & GUSSETS Phase Hardware 2 1/2" Deck Screws (24) 1 3/4" Deck Screws (24) Phase Parts (8) 1 X 2 9/16 X 17 5/16 GUSSET - LN204 (4) 11/16 X 3 1/2 X 21 SANDBOX SEAT - LR294 (4) 11/16 X 3 1/2 X 14 SANDBOX SEAT - LR295 (4) 11/16 X 3 1/2 X 7 SANDBOX SEAT - LR296 MAKE SURE FRAME IS SQUARE BEFORE ATTACHING GUSSETS! GROUND BOARD MAKE SURE FRAME IS SQUARE BEFORE PROCEEDING TO NEXT PHASE! UPRIGHT GROUND BOARD FLUSH TYPICAL SEAT DETAIL LN204 2 1/2" DECK SCREW TYPICAL GUSSET DETAIL FL
FLOOR BOARD & BARRIER RAIL ATTACHMENT Phase 11: Phase Hardware (270) 1 3/4" Deck Screws Fender Washer 5/16" Split Washers (4) 5/16" x 4 1/4" Hex Bolts (4) (4) 5/16" T-nuts (4) Phase Parts (38) 11/16 X 3 1/2 X 39 3/8 FLOOR BRD. - LR243 (2) 11/16 X 1 1/4 X 39 3/8 FLOOR BOARD - LS112 (2) 1 5/16 X 3 1/2 X 64 7/16 BARRIER RAIL - LM283 (18) 11/16 X 3 1/2 X 23 5/8 BRIDGE FLOOR BRD.
Phase 12: Phase Hardware LOWER WALL RAILS 2 1/2" Deck Screws Fender Washer (24) 5/16" x 2 1/2" Lag Screws (4) (12) (12) 5/16" T-nuts Phase Parts (2) 1 X 3 1/2 X 65 WALL RAIL - LM213 (4) 11/16 X 3 1/2 X 20 11/16 WALL RAIL- LR242 (4) 1 X3 1/2 X 11 WALL RAIL - LM226 (4) 1 X 3 1/2 X 7 WALL RAIL - LM227 (2) 11/16 X 3 1/2 X 64 7/16 WALL RAIL - LR282 LM226 LM226 1/8” PRE-DRILL HOLES FOR ALL LAG SCREWS LM226 LR242 LM226 LR242 LR282 LM213 LM213 LR282 LM227 NOTE: ALL RAILS ARE RESTING ON FORT F
Phase 13: Phase Hardware UPPER WALL RAILS 2 1/2" Deck Screws (24) 5/16" x 2 1/2" Lag Screws (4) Fender Washer (4) Phase Parts (2) 1 X 3 1/2 X 65 WALL RAIL- LM213 (4) 11/16 X 3 1/2 X 20 11/16 WALL RAIL - LR242 (2) 11/16 X 3 1/2 X 64 7/16 WALL RAIL - LR282 1/8” PRE-DRILL HOLES FOR ALL LAG SCREWS 3" BRIDGE BARRIER RAIL NOT SHOWN FOR CLARITY 3" LAG SCREWS FLUSH 3" LAG SCREWS FLUSH LR282 3" FLUSH 3" LR242 LM213 3" 30
Phase 14: SWING BEAM BRACE & ARCH RAILS Phase Hardware Fender Washer 5/16" Split Washers 5/16"x4"HexBolts (4) (4) 5/16" x 2 1/2" Lag Screws (16) (20) 2 1/2" Deck Screws (4) (16) 5/16" T-nuts Phase Parts (1) 1 3/8 X 5 5/16 X 65 SWING BEAM CROSS BRACE- LF250 (2) 1 X 5 5/16 X 44 3/4 LAD.
Phase 15: TARP UPRIGHTS & SUPPORTS Phase Hardware (42) 1 3/4" Deck Screws Phase Parts (2)1 X 3 1/2 X 66 15/16 TARP UPRIGHT - LM230 (4) 11/16 X 3 1/2 X 39 3/8 TARP END SUPP.. - LR234 (2)1 X 3 1/2 X 25 5/16 TARP UPRIGHT - LM231 (2) 11/16 X 3 1/2 X 37 3/8 TARP TOP SUPP.. - LR235 LR235 LR234 LM230 MAKE SURE FRAMES ARE SQUARE! 90° LM231 DECK SCREWS FLUSH 90° FLUSH 13 1/2 LR234 90° CENTER TARP UPRIGHT BETWEEN FORT UPRIGHTS, REST END ON FLOOR AND ATTACH WITH 1 3/4" DECK SCREWS.
Phase 16: WALL SLATS SIDES 1 & 2 Phase Parts Phase Hardware 1 1/8" Deck Screws (64) TYPICAL SPACING 27 8 (16) 5/8 X 3 1/2 X 23 5/8 WALL SLAT - LR240 TARP UPRIGHT TYPICAL SPACING 27 8 REST ON FLOOR SIDES 1 & 2 VIEW FROM INSIDE SI D SI D E1 33 E2
Phase 17: WALL SLATS SIDES 3,4 & 5,6 Phase Hardware (48) 3/4" Tapping Screws 1 1/ 8 " Deck Screws (16) Phase Parts (12) 5/8 X 3 1/2 X 23 5/8 WALL SLAT - LR240 (8) GREEN L-BRACKET - M003 WALL SLAT L-BRACKET AGAINST RAIL 3/4" TAPPING SCREW FLOOR L-BRACKET DETAIL SIDES 3 & 4 VIEW FROM INSIDE FLUSH L-BRKT. SIDES 5 & 6 VIEW FROM INSIDE E SI D E SI D FLUSH L-BRKT.
Phase 18: WALL SLATS SIDES 7,8 & 9 - 12 Phase Hardware 1 1/8" Deck Screws (104) Phase Parts (26) 5/8 X 3 1/2 X 23 5/8 WALL SLAT - LR240 234 234 3 TYPICAL SPACING 221 221 REST ON FLOOR SIDES 7 & 8 VIEW FROM INSIDE S ID E7 D SI S ID E1 1 S ID S ID E1 2 E1 0 SIDES 9 - 12 VIEW FROM INSIDE E9 S ID 35 E8
Phase 19: SWING BEAM ASSEMBLY Phase Hardware 5/16" x 4 1/2" Hex Head Bolt Fender Washer 5/16" Flat Washers 5/16" Lock Nuts (1) (9) 5/16" x 3 1/4" Hex Head Bolt 5/16" x 3 1/2" Lag Screws (2) (2) (18) (2) 5/16" x 4" Hex Bolts (6) Phase Parts (1) 3 5/16 X 5 5/16 X 89 1/2 SWING BEAM - LA251 (2) 1 3/8 X 3 5/16 X 82 1/2 SWING ANGLE BRACE - LG252 (1) 1 3/8 X 3 5/16 X 89 SWING GROUND BOARD - LG253 (1) 3 5/16 X 2 11/16 X 83 SWING END BEAM - LD254 (2) GREEN 4 HOLE TRIANGLE PLATE - M100 (2) GREEN AN
SWING BEAM ASSEMBLY Phase 20: Phase Hardware PLEASE REFER TO ACCESSORY PLAN(S) FOR INSTALLATION INSTRUCTIONS AND HARDWARE (1) GLIDER - BP 018-GY w/ HARDWARE Phase Parts (2) ULTIMATE SWING SEAT - BP014-Y (1) GLIDER SEAT (1 PAIR) GLIDER BRACKET BP 020 w/ HARDWARE (4) ULTIMATE SWING HANGER KC 003 w/ HARDWARE (2) GLIDER ARM 1/2” LOCK NUT & 3/4” WASHERS (4) CHAIN w/ EYE BOLT 1/2” LOCK NUT & 7/8” WASHERS NOTE: TIGHTEN LOCK NUTS UNTIL (3) THREADS ARE EXPOSED 7-1/2” HEX BOLT & 3/4” WASHER EYE BOLT ORIEN
Phase 21: SWING BEAM ATTACHMENT Phase Hardware 5/16" x 1 1/4" Hex Bolts 5/16" Split Washers (4) (4) Fender Washer (4) 5/16" T-nuts (4) T-NUTS INSTALLED ON BACKSIDE IN PHASE 14 1 1/4” HEX BOLT, 5/16” SPLIT WASHER & FENDER WASHER CENTER ID TAG AND ATTACH WITH 3/4” DECK SCREWS SWING ACCESSORIES NOT SHOWN FOR CLARITY (DO NOT ALLOW CHILDREN TO PLAY ON FORT / SWING ACCESSORIES UNTIL ASSEMBLY IS COMPLETE) 38 (1) ID Tag (2) 3/4 Deck Screw CreativeCedarDesigns.
Phase 22: HAND GRIP ATTACHMENT Phase Parts PLEASE REFER TO ACCESSORY PLAN(S) FOR INSTALLATION HARDWARE ( 2 PAIR ) SAFETY HANDLE BP007-Y w/ HARDWARE *Pre-drill holes with a 1/8” drill bit *Install all safety handles as shown.
Phase 23: STEERING WHEEL & TARP ATTACHMENT Phase Hardware PLEASE REFER TO ACCESSORY PLAN(S) FOR INSTALLATION HARDWARE Phase Parts (1) STEERING WHEEL BP 008-G w/ HARDWARE (2) TARP (GREEN) P005 w/ HARDWARE 5/16” T-NUT 2-1/4” HEX BOLT SPLIT WASHER & FENDER WASHER (DO NOT OVER TIGHTEN) REPLACE HUB COVER AFTER INSTALLING HARDWARE BRIDGE FLOOR STRETCH TARP TIGHT OVER SUPPORTS TARP SCREWS AND WASHERS INSIDE VIEW TARP (3) TARP SCREWS AND WASHERS PER SIDE BARRIER RAIL 40
Phase 24: SLIDE ATTACHMENT Phase Hardware #14 x 1” Truss Screw (8) Phase Parts LARGE WAVE SLIDE (GREEN) POSITION SLIDE CENTERED IN AN OPENING AND 4” INTO THE TOWER AS SHOWN.
Phase 25: Phase Parts ANCHORING (2) ANCHOR 4-PACK w/ HDW BP001-B STAKE FLAT WASHER METAL STRAP Phase Hardware (8) 1-1/2’’ LAG BOLT (8) FLAT WASHER STAKE STAKE 1-1/2’’ LAG BOLT STAKE ANCHOR STAKE STAKE *Place stakes into the ground next to playset as shown Note: Failure to use stakes can void warranty & cause injury. Final Step: Double check and make sure every bolt, screw and nut is tight. Make sure every board is secure. Make sure the fort is level and enjoy your playset.
LIMITED WARRANTY Creative Cedar Design (CCD) offers many fun, interactive, and safe play sets. We only guarantee the original purchaser that this product is free of defects for 30 days from the date of purchase. The product registration card, along with a dated purchase receipt, must be returned to CCD within 30 days. Within a 30 day period, CCD will repair or replace, at our option, defective merchandise free of charge, provided that the defective part is a manufacturer’s defect and not seasonal check.
Warranty claim procedure If you are confident that your play system has been installed and maintained properly, and you have a warranty claim, proceed with the following steps: 1. We will need copy of your proof of purchase (Vendor sales receipt only.) 2. We require a brief written description of the warranty issue. 3. Photos of warranted parts and of the entire play system. If any of the above steps are not completed, there may be delays in the completion of your claim, or possibly warranty cancellation.
PRODUCT REGISTRATION CARD Please complete this Product Registration Card along with a copy of the receipt and return to Creative Cedar Designs, within 30 days of original purchase in order to validate time of purchase for warranty. Or register at www.creativecedardesigns.
PRODUCT REGISTRATION CARD Please complete this Product Registration Card along with a copy of the receipt and return to Creative Cedar Designs, within 30 days of original purchase in order to validate time of purchase for warranty. FOLD HERE Place Stamp Here Creative Cedar Designs 2700 Riverside Dr.
