To be the Chief Evangelist CR-10S Pro Printer Guide Book To make Top-quality 3D printer ◆ This guide book is for standard CR-10S Pro. ◆ Please plug the power cord into a three-hole power jack. ◆ Detailed instructions for use are available on the TF card. V.1.
Contents 1. 2. 3. 4. 5. 6. Introduction....................................1 General List.....................................2 Device Installation..........................3 Cable Connection............................4 Screen Information.........................5 Loading Filament............................6 7. 8. 9. 10. 11. Bed Leveling......................................7 Software Installation........................9 For the First Printing........................10 Circuit Wiring..................
Notes 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Do not use the printer any way other than described herein in order to avoid personal injury or property damage. Do not place the printer near any heat source or flammable or explosive objects. We suggest placing it in a well-ventilated, low-dust environment. Do not expose the printer to violent vibration or any unstable environment, as this may cause poor print quality.
1. Introduction 14 1 7 9 15 2 16 3 8 5 4 1. 2. 3. 4. X Limit switch Nozzle kit Hot bed Touch screen 5. 6. 7. 8. 10 11 6 TF slot & USB port Z-axis motor (Z2) Z-axis coupler (Z2) Power switch & Power socket 1 9. 10. 11. 12. 12 Filament holder Y Limit switch Z-axis motor (Z1) Coupler (Z1) 13 13. 14. 15.
2.General List Base Frame Gantry Frame Tool Box Filament (200g） u No. 1 Tool List Image Name Qty Wrench & Screw 8 driver No. 6 Image Name Filament Holder Bracket Filament Holder Tube Filament Holder Tube Nuts Qty No. 1 Qty 11 PTFE Tube 1 12 X-Axis Spacer 1 13 Feeler 1 14 Spare Parts M5X25 black HexBolt and Lock Washer M4X8 Screw and M4 T- nut 2 TF Card & Reader 2 7 3 Spatula 1 8 4 Pliers 1 9 Power Cable 1 15 5 0.
3.
4. Cable Connection Z2 Ribbon Cable Z1 *Plug the power cord into a three-hole power jack.
5. Screen Information Screen Information Main Menu Automatic Sub Menu Explanation Stop Manual Choose to Print Pause/Continue Cooling TF card Fan Print speed Selected file Nozzle temp. Hot-bed temp Adjust Z offset Levelling fan Refuel Automatic Moving Manual Temp Motor PLA\ABS（195°\240°） Nozzle preheat Hot-bed preheat Cooling Printer info Cool down? Yes\No Fan Language Turn on\Shut down Z-axis：Z home，+0.1mm,-0.
6. Loading Filament u Feeding u Preheat Method 1 Press and hold the extruder lever and insert the 1.75mm filament through the filament detector and through the extruder motor. Continue feeding until you see filament extrude from the nozzle. Method 2 Replacing Filament During Print: 1、Cut the previous filament near the extruder and slowly feed new filament though the filament sensor and extruder, until the new filament is fed into the PTFE tube.
7. Bed Leveling pt.1 1. 2. Slightly tighten the four levelling nuts at the bottom of the platform before initial levelling. Select "Settings" → “Level mode” , click on the number ②. 5 4 1 2 3. 4. 5. 6. 3 Adjust the platform height by turning the knob underneath. Use a piece of A4 paper (standard printer paper) to assist with the adjustment, making sure that the nozzle lightly presses on the paper. Complete the adjustment on all 4 corners.
7. Bed Leveling pt. 2 u Automatic leveling 1. In “Settings” → “Leveling mode” → Place the .2mm feeler gauge between the nozzle and the hot bed → If the gap is too thin or too large, click "Z+" or "Z-" on the interface to adjust the gap to slightly more than 0.2 mm(the distance between the nozzle and the hot bed should be about 0.25 mm). At 0.2 mm the feeler can easily pass through the gap between the nozzle and the printing platform. 2.
8. Software Installation 300 300 1. Double click the Cura icon to install the Cura Slicing Software. 400 CR-10S Pro 2. Start Cura 3.0.2 from the Start Menu. 3. Select Other→Creality CR-10→ Rename the printer：CR-10S Pro →Add Printer. 4.Settings→Printer→Manage Printers... 5.Change Printer Settings to （300,300,400）.
9. The First Print 1. Slice test Open Cura → Open File → Select Model → Slice Model → Save to Removable Drive 2.
10.
11. After- Sales Service After-sales Service Card Product Name:________________________________ After-Sales Service Terms 1.We provide a 12-month warranty on 3D printers (excluding the nozzle assembly) purchased on or after January 1, 2017 and a 3-month warranty on the nozzle assembly thereof. Products purchased before January 1, 2017 whose warranty periods have not expired are subject to the original warranty terms. 2.The warranty period of each product starts from the date of production.
To be the Chief Evangelist Shenzhen Creality3D Technology CO.,LTD. Tel:+86 755-2103 4006 Official Website :www.creality3d.
