Certifications 2

Use standard firefighting procedures and consider the hazards of other involved materials.
Specific methods
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
Wear appropriate protective equipment and clothing during clean-up.
For non-emergency
personnel
Keep unnecessary personnel away. Ensure adequate ventilation. Local authorities should be
advised if significant spillages cannot be contained. For personal protection, see section 8 of the
SDS.
For emergency responders
Avoid discharge into drains, water courses or onto the ground.
6.2. Environmental precautions
Stop leak if you can do so without risk. Move the cylinder to a safe and open area if the leak is
irreparable. Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate
area). Keep combustibles (wood, paper, oil etc) away from spilled material. Absorb in vermiculite,
dry sand or earth and place into containers. Following product recovery, flush area with water.
Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to
remove residual contamination.
6.3. Methods and material for
containment and cleaning up
For personal protection, see section 8 of the SDS. For waste disposal, see section 13 of the SDS.
6.4. Reference to other
sections
SECTION 7: Handling and storage
Pressurised container: Do not pierce or burn, even after use. Do not use if spray button is missing
or defective. Do not spray on a naked flame or any other incandescent material Do not smoke
while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, or
expose containers to heat, flame, sparks, or other sources of ignition. Ground and bond containers
when transferring material. Do not re-use empty containers. Use only in well-ventilated areas.
Wear appropriate personal protective equipment. Observe good industrial hygiene practices.
7.1. Precautions for safe
handling
Contents under pressure. Do not expose to heat or store at temperatures above 120°F/49°C as
can may burst. Do not puncture, incinerate or crush. Do not handle or store near an open flame,
heat or other sources of ignition. Store away from incompatible materials (see Section 10 of the
SDS).
Storage class (TRGS 510): 2B (Aerosol dispensers and lighters)
7.2. Conditions for safe
storage, including any
incompatibilities
Not available.
7.3. Specific end use(s)
SECTION 8: Exposure controls/personal protection
8.1. Control parameters
No exposure limits noted for ingredient(s).
Occupational exposure limits
No biological exposure limits noted for the ingredient(s).
Biological limit values
Follow standard monitoring procedures.
Recommended monitoring
procedures
Derived no effect levels (DNELs)
General Population
NotesAssessment factorValueComponents
1,2-BENZISOTHIAZOL-3(2H)-ONE;1,2-BENZISOTHIAZOLIN-3-ONE (CAS 2634-33-5)
Long-term, Systemic, Dermal 200 Repeated dose toxicity0.345 mg/kg bw/day
Long-term, Systemic, Inhalation 50 Repeated dose toxicity1.2 mg/m3
Workers
NotesAssessment factorValueComponents
1,2-BENZISOTHIAZOL-3(2H)-ONE;1,2-BENZISOTHIAZOLIN-3-ONE (CAS 2634-33-5)
Long-term, Systemic, Dermal 100 Repeated dose toxicity0.966 mg/kg bw/day
Long-term, Systemic, Inhalation 25 Repeated dose toxicity6.81 mg/m3
Predicted no effect
concentrations (PNECs)
Not available.
8.2. Exposure controls
Good general ventilation should be used. Ventilation rates should be matched to conditions. If
applicable, use process enclosures, local exhaust ventilation, or other engineering controls to
maintain airborne levels below recommended exposure limits. If exposure limits have not been
established, maintain airborne levels to an acceptable level.
Appropriate engineering
controls
Individual protection measures, such as personal protective equipment
Personal protection equipment should be chosen according to the CEN standards and in
discussion with the supplier of the personal protective equipment.
General information
Wear safety glasses with side shields (or goggles). Use eye protection conforming to EN 166.
Eye/face protection
Skin protection
SDS UK
Material name: Flatscreen Cleaner - Manufacturers
BDS002561AE Version #: 01 Issue date: 03-June-2021
3 / 9