MSDS

Precautionary statement
Prevention
Obtain special instructions before use. Do not handle until all safety precautions have been read
and understood. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Do not
spray on an open flame or other ignition source. Do not apply while equipment is energized.
Pressurized container: Do not pierce or burn, even after use. Extinguish all flames, pilot lights
and heaters. Vapors will accumulate readily and may ignite. Avoid breathing mist or vapor. Avoid
breathing gas. Use only with adequate ventilation; maintain ventilation during use and until all
vapors are gone. Open doors and windows or use other means to ensure a fresh air supply during
use and while product is drying. If you experience any symptoms listed on this label, increase
ventilation or leave the area. Wash thoroughly after handling. Wear protective gloves/protective
clothing/eye protection/face protection. Avoid release to the environment.
Response
If swallowed: Immediately call a poison center/doctor. Do NOT induce vomiting. If on skin: Wash
with plenty of water. If skin irritation occurs: Get medical attention. Take off contaminated clothing
and wash before reuse. If inhaled: Remove person to fresh air and keep comfortable for
breathing. Call a poison center/doctor if you feel unwell. If in eyes: Rinse cautiously with water for
several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye
irritation persists: Get medical attention. If exposed or concerned: Get medical attention.
Storage
Store in a well-ventilated place. Store locked up. Protect from sunlight. Do not expose to
temperatures exceeding 50°C/122°F. Exposure to high temperature may cause can to burst.
Disposal
Dispose of contents/container in accordance with local/regional/national regulations.
Hazard(s) not otherwise
classified (HNOC)
Static accumulating flammable liquid can become electrostatically charged even in bonded and
grounded equipment. Sparks may ignite liquid and vapor. May cause flash fire or explosion.
3. Composition/information on ingredients
Mixtures
CAS numberCommon name and synonymsChemical name %
67-64-1acetone
20 - 30
68476-86-8liquefied petroleum gas
20 - 30
107-83-52-methylpentane
10 - 20
1330-20-7xylene
10 - 20
64742-49-0naphtha (petroleum), hydrotreated
light
5 - 10
108-65-6propylene glycol methyl ether
acetate
3 - 5
100-41-4ethylbenzene
1 - 3
110-54-3n-hexane
< 1
108-88-3toluene
< 0.2
26523-78-4tris(nonylphenyl) phosphite
< 0.2
Specific chemical identity and/or percentage of composition has been withheld as a trade secret.
4. First-aid measures
Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON
CENTER or doctor/physician if you feel unwell.
Inhalation
Remove contaminated clothing. Rinse skin with water/shower. If skin irritation occurs: Get medical
advice/attention. Wash contaminated clothing before reuse.
Skin contact
Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if
present and easy to do. Continue rinsing. Get medical attention if irritation develops and persists.
Eye contact
Call a physician or poison control center immediately. Rinse mouth. Do not induce vomiting. If
vomiting occurs, keep head low so that stomach content doesn't get into the lungs. Aspiration may
cause pulmonary edema and pneumonitis.
Ingestion
May cause drowsiness and dizziness. Headache. Nausea, vomiting. Severe eye irritation.
Symptoms may include stinging, tearing, redness, swelling, and blurred vision. Skin irritation. May
cause redness and pain.
Most important
symptoms/effects, acute and
delayed
Provide general supportive measures and treat symptomatically. Keep victim under observation.
Symptoms may be delayed.
Indication of immediate
medical attention and special
treatment needed
IF exposed or concerned: Get medical advice/attention. Ensure that medical personnel are aware
of the material(s) involved, and take precautions to protect themselves. Show this safety data
sheet to the doctor in attendance.
General information
2 / 13
Material name: Seal Coat® Clear Urethane Coating
18411 Version #: 02 Revision date: 12-07-2016 Issue date: 06-05-2014
SDS US