SDS

Contents under pressure. Pressurized container may rupture when exposed to heat or flame.
During fire, gases hazardous to health may be formed.
Specific hazards arising from
the chemical
Firefighters must use standard protective equipment including flame retardant coat, helmet with
face shield, gloves, rubber boots, and in enclosed spaces, SCBA.
Special protective equipment
and precautions for firefighters
Fire-fighting
equipment/instructions
In case of fire: Stop leak if safe to do so. Move containers from fire area if you can do so without
risk. Cool containers exposed to heat with water spray and remove container, if no risk is involved.
Containers should be cooled with water to prevent vapor pressure build up.
Extremely flammable aerosol. Contents under pressure. Pressurized container may rupture when
exposed to heat or flame.
General fire hazards
6. Accidental release measures
Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of
low areas. Many gases are heavier than air and will spread along ground and collect in low or
confined areas (sewers, basements, tanks). Wear appropriate protective equipment and clothing
during clean-up. Emergency personnel need self-contained breathing equipment. Do not touch
damaged containers or spilled material unless wearing appropriate protective clothing. Ventilate
closed spaces before entering them. Local authorities should be advised if significant spillages
cannot be contained. For personal protection, see section 8 of the SDS.
Personal precautions,
protective equipment and
emergency procedures
Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Keep
combustibles (wood, paper, oil, etc.) away from spilled material. Prevent product from entering
drains. Stop the flow of material, if this is without risk. Wipe up with absorbent material (e.g. cloth,
fleece). Clean surface thoroughly to remove residual contamination. Put material in suitable,
covered, labeled containers. For waste disposal, see section 13 of the SDS.
Methods and materials for
containment and cleaning up
Avoid release to the environment. Inform appropriate managerial or supervisory personnel of all
environmental releases. Prevent further leakage or spillage if safe to do so. Avoid discharge into
drains, water courses or onto the ground.
Environmental precautions
7. Handling and storage
Obtain special instructions before use. Do not handle until all safety precautions have been read
and understood. Pressurized container: Do not pierce or burn, even after use. Do not use if spray
button is missing or defective. Do not spray on a naked flame or any other incandescent material.
Do not smoke while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill,
grind, or expose containers to heat, flame, sparks, or other sources of ignition. Use caution around
energized equipment. The metal container will conduct electricity if it contacts a live source. This
may result in injury to the user from electrical shock and/or flash fire. Protect containers from
physical damage; do not drag, roll, slide, or drop. When moving containers, even for short
distances, use a cart (trolley, hand truck, etc.) designed to transport containers. Do not get in eyes,
on skin, or on clothing. Avoid prolonged or repeated contact with skin. Avoid prolonged exposure.
Pregnant or breastfeeding women must not handle this product. Should be handled in closed
systems, if possible. Use only in well-ventilated areas. Wear appropriate personal protective
equipment. Wash hands thoroughly after handling. Avoid release to the environment. Observe
good industrial hygiene practices. For product usage instructions, see the product label.
Precautions for safe handling
Level 3 Aerosol.
Pressurized container. Protect from sunlight and do not expose to temperatures exceeding
50°C/122 °F. Do not puncture, incinerate or crush. Do not handle or store near an open flame,
heat or other sources of ignition. This material can accumulate static charge which may cause
spark and become an ignition source. Store in a well-ventilated place. Store away from
incompatible materials (see Section 10 of the SDS).
Conditions for safe storage,
including any incompatibilities
8. Exposure controls/personal protection
Occupational exposure limits
The following constituents are the only constituents of the product which have a PEL, TLV or other recommended exposure limit.
At this time, the other constituents have no known exposure limits.
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
ValueComponents Type
PEL 240 mg/m32-butoxyethanol (CAS
111-76-2)
50 ppm
PEL 9000 mg/m3carbon dioxide (CAS
124-38-9)
5000 ppm
PEL 400 mg/m3distillates (petroleum),
hydrodesulfurized middle
(CAS 64742-80-9)
3 / 13
Material name: Engine Degreaser
No. 05025CA (Item# 1003644) Version #: 03 Revision date: 07-14-2017 Issue date: 09-18-2013
SDS US