Assembly Instruction

ManualsBrandsCrate & Barrel ManualsStorage FurnitureCrate & Barrel Wieden One-Door Cabinet

Made in China - r09 Page 1 of 5

Thank you for purchasing the Wieden 1 Door Cabinet.

This page lists all the contents included in the box.

Please take time to identify the hardware as well as the

individual components of this product. As you unpack

and prepare for assembly, place the contents on a

carpeted or padded area to protect them from damage.

Note: 2 people are required to safely assemble this product.

WIEDEN 1 DOOR CABINET

Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com

1 - top panel

2 - fixed shelves

1 - back panel

1 - base

assembly

1 - right side panel 1 - door front

ASSEMBLY HARDWARE

TOOLS REQUIRED

8 - bolts 8 - shelf

pins

30 - cam

screws

30 - wood

dowels

COMPONENTS

1 - left side panel

1 - partition

1 - bottom

panel

Missing hardware? Please call

800.606.6387 for replacements.

12 - small

screws

2 - adjustable shelves

3 - hinges30 - cams

phillips head screwdriver

(We recommend the use of hand tools instead power tools)

allen wrench (included)

1 - magnet

WALL MOUNTING HARDWARE

1 - wall strap 1 - small

screw

1 - plastic

anchor

1 - large

screw

2 - magnet

screws

Summary of content (5 pages)

PAGE 1
WIEDEN 1 DOOR CABINET ASSEMBLY HARDWARE Missing hardware? Please call 800.606.6387 for replacements. 30 - wood dowels 8 - bolts 30 - cam screws 30 - cams 3 - hinges 12 - small 8 - shelf pins screws 1 - magnet 2 - magnet WALL MOUNTING HARDWARE 1 - wall strap Thank you for purchasing the Wieden 1 Door Cabinet. This page lists all the contents included in the box. Please take time to identify the hardware as well as the individual components of this product.
PAGE 2
WIEDEN 1 DOOR CABINET NOTE: Do not over tighten the cam screws A left side panel back panel NOTE: Make sure arrows on each cam points toward nearest edge with holes B right side panel 1 Insert 10 cams into back panel as shown. Make sure arrows on each cam points toward nearest edge with holes. 2 A) Insert 3 wood dowels, 4 cams and 3 cam screws into left side panel as shown. Secure, but do not over tighten, cam screws using a phillips head screwdriver.
PAGE 3
WIEDEN 1 DOOR CABINET left side panel B A back panel partition fixed shelf right side panel 5 Fit dowels of left side panel and partition into corresponding holes of back panel. Using a phillips head screwdriver, turn cams clockwise until each cam securely engages each cam screw. 6 A) Insert 4 cams into each fixed shelf as shown. B) Fit dowels of partition and right side panel into corresponding holes of 2 fixed shelves. Secure all cams.
PAGE 4
WIEDEN 1 DOOR CABINET NOTE: Do not over tighten the screws A adjustable shelf door front 9 With the assistance of another adult, position unit upright as shown. Place 2 adjustable shelves onto shelf pins. Make sure shelves are securely supported by each shelf pin. 10 Attach 3 hinges to door front with 2 small screws per hinge as shown. Secure, but do not over tighten, screws with a phillips head screwdriver. Refer to Hinge Adjustment diagram for adjusting the alignment of the door hinges.
PAGE 5
WIEDEN 1 DOOR CABINET OPTIONAL SAFETY MOUNTING INSTRUCTIONS NOTE: Insert screws 3/4"-1" from the edge of the strap For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe mounting, it is essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete, etc.). Mount to wood studs whenever possible. wall strap A) Determine the final location of unit. Mark position on the wall, approximately 2” below the top of the unit as shown.