Assembly Instruction

ManualsBrandsCrate & Barrel ManualsStorage FurnitureCrate & Barrel Sentry Wall Box

SENTRY WALL BOX

drill

Made in China - r05 Page 1 of 2

Thank you for purchasing the Sentry Wall Box. This page

lists all the contents included in the box. Please take the

time

to identify the hardware as well as the individual

components

to this product. As you unpack and prepare

for assembly, place the contents on a carpeted or

padded area to protect them from damage.

Missing hardware?

Please call 800.606.6387 for replacements.

HARDWARE FOR WALL BOX WITH SHELF

Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com

TOOLS REQUIRED

phillips head

screwdriver

2 - wall

brackets

INSTALLATION INSTRUCTIONS

For safe mounting, it is essential to use wall anchors

appropriate to your wall type (i.e. plaster, drywall,

concrete, brick etc.). Mount to wood studs whenever

possible. The following instructions are for drywall

mounting only:

A. Determine final location of wall box. Position the

wall brackets 16” (41cm) apart as shown. Make sure

wall brackets are level and mark the 4 hole locations

onto the wall. Set wall brackets aside until further

instructions.

B. Drill 4 pilot holes into marked positions on the wall

and into a wall stud. If the wall stud is not available, drill

a hole at each mark slightly smaller than the diameter of

the anchor.

C. Insert 4 anchors into holes. Make sure the flange of

each anchor is flush with the wall.

D. Attach wall brackets to the wall by inserting 2 bolts

through each bracket and each anchor in the wall.

WEIGHT LIMITATION

The Sentry Wall Box with Shelf is able to support up to

a total of 30 lbs and the Sentry Wall Box with Drawers

10 lbs per drawer.

WALL

wall

bracket

anchor

NOTE: If you are unsure about

your wall type or what mounting

method you should use, consult a

qualified professional or your local

hardware store.

4 - shelf

pins

”

)

HARDWARE FOR WALL BOX WITH DRAWERS

4 - anchors

(for brick)

4 - screws

(for brick)

4 - anchors

(for drywall)

2 - wall

brackets

4 - bolts

(for drywall)

4 - anchors

(for brick)

4 - screws

(for brick)

4 - anchors

(for drywall)

4 - bolts

(for drywall)

Summary of content (4 pages)

PAGE 1
SENTRY WALL BOX HARDWARE FOR WALL BOX WITH SHELF 4 - screws 4 - anchors 4 - bolts (for brick) (for brick) 4 - anchors 2 - wall 4 - shelf brackets pins (for drywall) (for drywall) HARDWARE FOR WALL BOX WITH DRAWERS 4 - screws 4 - anchors 4 - bolts (for brick) Thank you for purchasing the Sentry Wall Box. This page lists all the contents included in the box. Please take the time to identify the hardware as well as the individual components to this product.
PAGE 2
SENTRY WALL BOX ASSEMBLY INSTRUCTIONS FOR WALL BOX WITH SHELF 1 With the assistance of another adult, fit preassembled brackets on back of unit into wall brackets on wall as shown. Make sure unit is securely supported by each bracket. WALL pre-assembled wall bracket wall bracket wall box 2 A) Insert 4 shelf pins as shown. B) Place shelf into wall box as shown. Make sure shelf is securely supported by each shelf pin. Assembly is now complete. A A B shelf Made in China - r05 Customer Service 800.
PAGE 3
SENTRY WALL BOX ASSEMBLY INSTRUCTIONS FOR WALL BOX WITH DRAWERS NOTE: The removal of the drawers is not necessary to properly install the wall box. Doing this only allows you to reduce the weight for lifting during installation. 1 Extend drawer as far as possible. Using a phillips head screwdriver, remove small screws from drawer bottom as shown. Repeat for all remaining drawers. Set drawers and screws aside.
PAGE 4
SENTRY WALL BOX drawer drawer glide A. Extend drawer glides from assembly as far out as possible. Fit drawer onto glides as shown. B. Align holes of drawer glides with drawer bottom and secure with small screws, using a phillips head screwdriver. Do not over tighten the screws. C. Push drawer into assembled unit. Repeat A-C for all remaining drawers. Assembly is now complete. CLEANING AND CARE Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners.