Assembly Instruction

ManualsBrandsCrate & Barrel ManualsStorage FurnitureCrate & Barrel Paterson Corner Media Stand C1

COMPONENTS

Made in China - r13 Page 1 of 6

Thank you for purchasing the Paterson Corner Media

Stand. This page lists all the contents included in the

box. Please take time to identify the hardware as well as

the individual components of this product. As you

unpack and prepare for assembly, place the contents on

a carpeted or padded area to protect them from damage.

Note: 2 people are required to safely assemble this product.

PATERSON CORNER MEDIA STAND

1 - top panel

2 - small side panels

(1 left, 1 right)

1 - shelf

ASSEMBLY HARDWARE

TOOLS REQUIRED

Missing hardware? Please call 800.606.6387 for replacements.

4 - pull bolts26 - wood

dowels

phillips head screwdriver

(We recommend the use of hand tools instead power tools)

1 - base

1 - back panel

2 - pulls

24 - small

screws

2 - doors

(1 left, 1 right)

2 - barrel

nuts

4 - shelf

pins

10 - small

bolts

2 - large

bolts

4 - hinges

2 - large side panels

12 - large

screws

6 - cam

screws

6 - cams

4 - small

screws

WALL MOUNTING HARDWARE

2 - large

screws

2 - plastic

anchors

2 - wall

straps

2 - wall

brackets

2 - anti-tip

brackets

Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com

Summary of content (6 pages)

PAGE 1
PATERSON CORNER MEDIA STAND ASSEMBLY HARDWARE 26 - wood 6 - cam 10 - small screws bolts dowels 2 - large bolts 4 - pull bolts 24 - small screws 12 - large 2 - barrel 6 - cams screws nuts 4 - shelf pins 4 - hinges Missing hardware? Please call 800.606.6387 for replacements. WALL MOUNTING HARDWARE Thank you for purchasing the Paterson Corner Media Stand. This page lists all the contents included in the box.
PAGE 2
PATERSON CORNER MEDIA STAND NOTE: Do not over tighten the bolts A top panel NOTE: Do not over tighten the cam screws B large side panel NOTE: Make sure ledge on panel is positioned as shown top panel base 1 A) Fit 13 wood dowels into top panel as shown. B) Insert 6 cam screws into base as shown. Secure, but do not over tighten, cam screws using a phillips head screwdriver. 2 Fit pre-installed dowels of top panel into corresponding holes of large side panel.
PAGE 3
PATERSON CORNER MEDIA STAND NOTE: Do not over tighten the screws left small side panel right small side panel B right small side panel A left small side panel back panel 5 Secure left and right small side panels to top panel with 2 small bolts per side as shown. C NOTE: Make sure hole of barrel nut aligns with the hole in nearest edge 6 A) Secure large side panels to left/right small panels and back panel with 6 large screws as shown, using a phillips head screwdriver.
PAGE 4
PATERSON CORNER MEDIA STAND Refer to Hinge Adjustment diagram for adjusting the alignment of the door hinges A A B right door front pull left door front B left and right door fronts 8 Attach 2 hinges to left and right door fronts with 2 screws per hinge as shown, using a screwdriver. 9 A) With the assistance of another adult, position unit upright. Attach left and right door fronts to assembled unit as shown. Secure each hinge with 4 screws. B) Attach 2 pulls to left and right door fronts as shown.
PAGE 5
PATERSON CORNER MEDIA STAND CLEANING AND CARE Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as the wood is finished with a protective clear lacquer. HINGE ADJUSTMENT If the doors do not appear square or aligned, loosen or tighten the appropriate screws on each case hinge as illustrated. 1) Side to side adjustment: Loosen screw A, adjust gap with screw B and re-tighten screw A.
PAGE 6
PATERSON CORNER MEDIA STAND C plastic anchor F wall strap wall bracket anti-tip bracket D large screw A small screw OPTIONAL WALL MOUNTING INSTRUCTIONS: For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe mounting, it is essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete, etc.). Mount to wood studs whenever possible. A) Attach 1 anti-tip bracket to top of unit as shown, using 2 small screws.