Assembly Instruction

ManualsBrandsCrate & Barrel ManualsStorage FurnitureCrate & Barrel Loop Six-Drawer Dresser

HARDWARE

TOOLS REQUIRED

COMPONENTS

Made in China r11 Page 1 of 5

Thank you for purchasing the Loop 6 Drawer Dresser.

This page lists all the contents included in the box.

Please take time to identify the hardware as well as the

individual components of this product. As you unpack

and prepare for assembly, place the contents on a

carpeted or padded area to protect them from damage.

NOTE: 2 people are required to safely assemble this

product.

LOOP 6 DRAWER DRESSER

Missing hardware? Please call 800.606.6387 for replacements.

24 - cam

screws

12 - silver

screws

13 - black

screws

17 - wood

dowels

24 - cam

covers

24 - cams

6 - pulls

24 - glide

screws

Phillips Head Screwdriver

Customer Service 800.967.6696 | www.crateandbarrel.com

1 - top panel

2 - side frames

(1 left, 1 right)

1 - crossbar

6 - drawer fronts

(3 labeled LEFT, 3 labeled RIGHT on

back of drawer fronts)

1 - back panel

6 - drawer backs

12 - drawer sides

(6 right, 6 left)

6 - drawer bottoms1 - middle

partition

LEFT

RIGHT

Summary of content (5 pages)

PAGE 1
LOOP 6 DRAWER DRESSER HARDWARE 24 - cams 17 - wood dowels Thank you for purchasing the Loop 6 Drawer Dresser. This page lists all the contents included in the box. Please take time to identify the hardware as well as the individual components of this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage. NOTE: 2 people are required to safely assemble this product.
PAGE 2
LOOP 6 DRAWER DRESSER Arrow on each cam points towards edge with holes A B C 1 A) Place left side panel face down on a padded surface. Insert 4 cam screws into the holes as shown. Secure, but do not over tighten with a phillips head screwdriver. B) Insert 3 cams into the large holes as shown, making sure the arrow on each cam points towards the nearest edge with holes. C) Insert 2 wood dowels into the top edge of the panel. Repeat Steps A, B & C for the right side panel.
PAGE 3
LOOP 6 DRAWER DRESSER crossbar middle partition middle partition 5 Secure 3 cams at the base of the middle partition with a Phillips head screwdriver. Turn each cam clockwise until it securely engages each cam screw. 6 Carefully turn the middle partition and back panel assembly on end as shown. Fit dowel of middle partition into corresponding hole of crossbar. Secure crossbar with 1 black screw as shown, using a Phillips head screwdriver.
PAGE 4
LOOP 6 DRAWER DRESSER top panel top panel 9 Insert 13 cam screws into the underside of the top panel as shown. 11 Slide left and right drawer sides up into slots on back of the drawer front. Make sure glide hardware is on the outside of the drawer sides and the vertical slots are at the back of the assembly as shown. Made in China r11 10 With assistance of another adult, position assembled unit upright. Fit cam screws of top panel into corresponding holes of assembled unit as shown.
PAGE 5
LOOP 6 DRAWER DRESSER B A These holes at back 13 A) Secure underside of drawer bottom to drawer back with 2 black screws. Secure, but do not over tighten with the phillips head screwdriver. B) Fit drawer pull into position as shown and secure with 2 silver screws. Repeat Steps 8 - 11 for remaining 5 drawers. 12 Slide drawer bottom into slot at base of drawer sides and drawer front. Make sure pilot holes are at the back of the drawer bottom as shown.