Assembly Instruction

ManualsBrandsCrate & Barrel ManualsStorage FurnitureCrate & Barrel Latitude Media Stand

Customer Service 800-967-6696 | http://www.crateandbarrel.com

LATITUDE MEDIA STAND

HARDWARE

TOOLS REQUIRED

Phillips head screwdriver

COMPONENTS

2 - side panels

(1 left, 1 right)

Made in Denmark 2004

Page 1 of 6

Thank you for purchasing the Latitude Media Stand.

This page lists all the contents included in the box. Please

take time to identify the hardware as well as the individual

components of this product. As you unpack and prepare

for assembly, place the contents on a carpeted or padded

area to protect them from damage.

30 - wood

dowels

10 - long

wood screws

8 - short

wood screws

26 - large cams

4 - small cams

30 - cam screws

26 - cam

covers

2 - drawer backs

2 - drawer fronts

1 - bottom panel

(has 10 pilot holes on underside)

2 - drawer bottoms

4 - drawer side

panels (2 left, 2 right)

2 - shelves

1 - top panel

1 - back panel

1 - middle panel

4 - long machine

screws

4 - short

machine screws

2 - metal pull handles

4 - medium

wood screws

4 - drawer

glides

4 - metal pull standoffs

1 - metal

base frame

4 - metal legs

Summary of content (6 pages)

PAGE 1
LATITUDE MEDIA STAND HARDWARE 30 - wood dowels Thank you for purchasing the Latitude Media Stand. This page lists all the contents included in the box. Please take time to identify the hardware as well as the individual components of this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage.
PAGE 2
LATITUDE MEDIA STAND Make sure arrow on drawer slide points forward Left Side Panel 1 Fully extend the drawer glide. Position the first hole at the back end of the glide over the pre-drilled hole in the left side panel. Attach back of glide with 1 short wood screw. 2 Retract the glide as shown. Position 1 short wood screw over the oval hole on the external portion of the glide and through the third hole on the inside portion of the glide.
PAGE 3
LATITUDE MEDIA STAND Make sure arrow on drawer glide points forward x2 A Middle panel B 5 Using a screwdriver, turn 2 cams 90 degrees clockwise to secure shelf panel to left side panel. 6 A. Repeat Steps 1 & 2 to attach 2 drawer glides to the middle panel (1 on each side), with short wood screws. B. Fasten 2 cam screws to the outer holes of middle panel. Middle panel Back Panel A A B B 7 A. Insert 2 wood dowels into the inner holes of left shelf edge. B.
PAGE 4
LATITUDE MEDIA STAND Right Side Panel (outside) 9 Attach right side panel using assembly method in Steps 3 - 5. Insert 2 dowels and 2 cam screws into the right side panel. Secure cams with a screwdriver. 10 Insert 9 large cams into the holes at the tops of the side and middle panels, making sure that arrows point towards the top edge of the panels.
PAGE 5
LATITUDE MEDIA STAND 13 Fit each metal leg into the corner brackets of the metal base frame, aligning the holes in legs with holes in the brackets. Insert 1 long machine screw through the corner bracket into each leg and secure with a screwdriver. 14 Align the 10 holes in the base frame with the pilot holes in the bottom panel and attach with 10 long wood screws. DRAWER CONSTRUCTION A B x2 x2 15 A. Attach drawer side panels to drawer back panel using 2 medium wood screws. B.
PAGE 6
LATITUDE MEDIA STAND B A C x2 17 A. Insert 2 cam screws into the back side of the drawer front. B. Fit drawer front onto the drawer assembly and secure the 2 cams with a screwdriver. C. Insert 2 long machine screws through the drawer front and the 2 metal pull standoffs, then into the threaded holes of the metal pull. Tighten with a screwdriver. 18 Fully extend drawer glides. Slide assembled drawers onto drawer glides, fitting drawer slides into grooves on drawer side panels.