Assembly Instruction

ManualsBrandsCrate & Barrel ManualsStorage FurnitureCrate & Barrel Latitude Large Media Stand

Customer Service 800-967-6696 | http://www.crateandbarrel.com

HARDWARE

Thank you for purchasing the Latitude Large

Media Stand. This page lists all the contents

included in the box. Please take time to identify

the hardware as well as the individual components

of this product. As you unpack and prepare for

assembly, place the contents on a carpeted or

padded area to protect them from damage.

Note: 2 people are required to safely assemble this

product.

COMPONENTS

1 - top panel

1 - bottom panel

(holes on bottom)

1 - middle shelf

TOOLS REQUIRED

Phillips head screwdriver

2 - doors

(1 left, 1 right)

4 - legs

1 - middle back panel

2 - side shelves

2 - back panels

1 - base frame

2 - side panels

(1 left, 1 right)

2 - divider

panels

2 - door pull handles

4 - door pull standoffs

These holes

on both sides

LATITUDE LARGE MEDIA STAND

Page 1 of 5

Made in Denmark - r09

Missing hardware? Please call 800.606.6387 for replacements.

36 - wood

dowels

36 - cams

36 - cam screws

36 - cam covers 2 - door stops

4 - door pull

bolts

12 - shelf pins

12 - wood screws

4 - leg bolts

4 - case

hinges

4 - door

hinges

16 - hinge screws

Summary of content (5 pages)

PAGE 1
LATITUDE LARGE MEDIA STAND HARDWARE 36 - cams 36 - wood dowels 36 - cam screws Thank you for purchasing the Latitude Large Media Stand. This page lists all the contents included in the box. Please take time to identify the hardware as well as the individual components of this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage. Note: 2 people are required to safely assemble this product.
PAGE 2
LATITUDE LARGE MEDIA STAND NOTE: Do not over tighten the screws. 1 Place 4 legs at each corner of the base frame, aligning hole in leg with hole in bracket. Attach with 1 leg bolt per leg, fully tightening with a phillips head screwdriver. 2 Position base frame assembly over holes in the bottom panel. Insert 12 wood screws through holes in frame and into bottom panel and secure with a screwdriver.
PAGE 3
LATITUDE LARGE MEDIA STAND C A Back Panel Divider Panel D Left Side Panel Back Panel B Divider Panel 5 A. Insert 4 wood dowels into the outer holes on edges of each back panel. B. Insert 4 cams into each back panel, making sure arrows on cams points towards nearest edge. C. Insert 6 wood dowels into outer holes on edge of divider panels. D. Insert 2 cam screws into the inner holes at the rear of each divider panel. 7 A. Insert 4 wood dowels into the outer holes on the edges of the middle back panel.
PAGE 4
LATITUDE LARGE MEDIA STAND Cam in unlocked position Cam in locked position 9 Using a phillips head screwdriver, turn each cam at the base of the side panels clockwise until each cam tightly engages the cam screw. 10 Insert 12 shelf pins into the holes in the side and divider panels at desired shelf heights. A B 11 Fit 2 side shelves and 1 middle shelf into position. Make sure each shelf is securely supported by the shelf pins. 12 A.
PAGE 5
LATITUDE LARGE MEDIA STAND A A B B 14 A. Fit each door hinge onto the case hinge installed on the side panels. Temporarily secure the set screw with a screwdriver and refer to the instructions below for final adjustment of the door and hinges. B. Conceal all exposed cams with cam covers. Assembly is now complete. 13 A. Fit cup of 2 door hinges into large holes on both door interiors. Secure each with 2 hinge screws per hinge. B.