Assembly Instruction

ManualsBrandsCrate & Barrel ManualsStorage FurnitureCrate & Barrel Kenton Cube with Two Drawers

Customer Service 800-967-6696 | http://www.crateandbarrel.com

HARDWARE

Thank you for purchasing the Kenton Cube

with 2 Drawers. This page lists all the

contents included in the box. Please take

time to identify the hardware as well as the

individual components of this product. As

you unpack and prepare for assembly,

place the contents on a carpeted or

padded area to protect them from damage.

COMPONENTS

TOOLS REQUIRED

Phillips head screwdriver

KENTON CUBE WITH 2 DRAWERS

Page 1 of 3

Made in China - r07

Missing hardware? Please call 800.606.6387 for

replacements.

8 - cam

screws

8 - cams

8 - wood

dowels

1 - back panel

4 - pull screws

1 A. Insert 4 wood dowels into the inner holes on the

edges of the 2 side panels.

B. Insert 4 cams into the large holes in each side panel.

Make sure arrow on each cam points out towards edge

with dowels.

24 - large screws

Make sure

arrow on

each cam

points towards

edge with dowels

2 - drawer bottoms

24 - small screws

2 - drawer pulls

4 - drawer sides

(2 left, 2 right)

2 - inner drawer

front panels

2 - drawer fronts

2 - drawer backs

4 - glide assemblies

2 - end panels

(1 labeled top,

1 labeled bottom)

2 - side panels

(left labeled L, right

labeled R)

Summary of content (5 pages)

PAGE 1
KENTON CUBE WITH 2 DRAWERS HARDWARE 8 - cams 8 - cam screws 24 - large screws Thank you for purchasing the Kenton Cube with 2 Drawers. This page lists all the contents included in the box. Please take time to identify the hardware as well as the individual components of this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage.
PAGE 2
KENTON CUBE WITH 2 DRAWERS NOTE: Do not over tighten the screws. A Depress plastic tab to detach small glide from large glide assembly C B 2 Remove the small component of each glide assembly. Attach 2 of the large glides to the left and right side panels with 3 small screws per glide, orienting each glide as shown. The front of each glide should sit approximately 3/4" from the front edge of the panel. Secure, but do not over tighten each screw with a phillips head screwdriver.
PAGE 3
KENTON CUBE WITH 2 DRAWERS A IMPORTANT: Make sure unfinished edge of drawer side faces forward A B C B 6 A. Attach left drawer side to drawer back and inner drawer front with 4 large screws. Make sure unfinished edge faces forward. Secure, but do not over tighten each screw with a phillips head screwdriver. B. Slide drawer bottom into slot at bottom of assembly. Repeat Steps A & B for the other drawer. 7 A. Attach right drawer side to drawer assembly with 4 large screws. B.
PAGE 4
KENTON SINGLE AND DOUBLE CUBE WITH 2 DRAWERS ADJUSTING THE DRAWER FRONTS If the drawer fronts appear uneven or misaligned, open each drawer. Loosen each drawer slide screw enough to allow for movement of the drawer. Make any necessary adjustments to the drawers and re-tighten the drawer glide screws. Page 1 of 1 Made in China - r03 Customer Service 800-967-6696 | http://www.crateandbarrel.
PAGE 5
KENTON SINGLE & DOUBLE CUBE ATTACHMENT MULTIPLE CUBE STACKING FOR SINGLE & DOUBLE CUBES TOOLS REQUIRED Phillips head screwdriver HARDWARE INCLUDED Single Cube - 2 wood screws Double Cube - 4 wood screws Single Cube - 1 mending plate Double Cube - 2 mending plates NOTE: Do not stack more than 5 cubes high A B 1 A. Stack cubes in desired configuration, making sure the rear edges of each cube are aligned and flush. B.