品号：32280107500031 32 INCH STEREO SOUND BAR SYSTEM with Digital Optical Input and Bluetooth®® Wireless Technology Owner's Manual PLEASE READ BEFORE OPERATING THIS EQUIPMENT. Model: CHT985 Size: 148.
IMPORTANT SAFETY INSTRUCTIONS FCC Warnings WARNING:Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
IMPORTANT SAFETY INSTRUCTIONS 3
POWER SOURCE 1. Insert the small plug from the supplied AC/DC Adapter to the DC IN Jack on the rear of unit. 2. Connect the AC/DC Adapter to the wall outlet having AC 100-240V~; 50/60Hz. The Red Standby Indicator on the front of unit will illuminate. To the wall outlet DC DC IN 5.8V, 1.5A To the DC IN jack on the rear of the unit. NOTES: To save energy, unplug the AC/DC Adaptor from the wall outlet if you may not use the unit for an extended period of time.
Mounting to a wall 2.1 Mounting to a wooden wall 19. 3 in che s A. Mark the position of the mounting screws on the wall using a pencil. B. Drill the supplied mounting screws directly into the marks that you have made on the wall and leave approx. 0.3 inches length to hook the sound bar. C. Put the sound bar onto the mounting screws. Make sure they are firm and stable. 2.2 Mounting to a brick wall 19. 3 in (1) che s (2) A. Mark the position of the mounting screws on the wall using a pencil. B.
LOCATION OF CONTROLS Front View 1 3 2 1 Rear View AU X I N 1 DC AU X I N 2 OPTICAL IN R 7 6 5 4 L DC IN 5.8V,1.5A Top View 8 9 10 1. Speakers 2. Remote Sensor 3. Indicators 4. OPTICAL IN Jack 5. AUX IN 2 Jack 6. AUX IN 1 Jacks 11 7. DC IN Jack 8. STANDBY/SOURCE Button 9. (Play/Pause) Button 10. (Volume Down/Skip Backward) Button 11.
LOCATION OF CONTROLS - REMOTE CONTROL 1 6 2 3 4 5 7 1. (Standby On/Off) Button 2. (Play/Pause) Button 3. (Skip Backward) Button 4. SOURCE Button 5. VOL- (Volume Down) Button 8 6. (Mute) Button 7. (Skip Forward) Button 8. VOL+ (Volume Up) Button BUTTON CELL INSTALLATION - REMOTE CONTROL First Time Use: Remove and discard the insulation film as illustrated on the right. If the button cell is drained, replace it by a new one as below: 1. Push and slide out the battery holder as Fig.1 below.
BATTERY PRECAUTIONS: Follow these Battery Precaution when using a battery in this device: 1. Use only the size and type of battery specified. 2. Be sure to follow the correct polarity when installing the battery as indicated in the battery compartment. A reversed battery may cause damage to the device. 3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones. 4.
OPERATIONS GENERAL OPERATION: 1. Connected the unit to AC power as previously instructed. The Red Standby Indicator on the front of unit will illuminate. 2. Press and hold the STANDBY/SOURCE Button on the top of unit approximately 2 seconds or press the Button on the Remote Control to power on the unit from Standby mode. 3. Press and release the STANDBY/SOURCE Button on the top of unit or press the SOURCE Button on the Remote Control repeatedly to switch to desired playback mode.
BT MODE: BT (Bluetooth) pairing: First time use or re-pairing the unit to a new BT Device, pair as follows: 1. Power on the unit and enter to BT mode as previously instructed. The color of the indicator on the front of unit will turn to Blue and blink. 2. Power on the external BT Device and enter to BT searching mode. Start pairing following the on screen instructions from the external BT Device. After paired, the Blue indicator will stop blinking. 3.
OPTICAL IN: Listen music from the Optical Out Jack from an external Video Player or Television: 1. Connect one end of the Optical Connection Cable (not included) to the Optical Out Jack on the external Video Player or Television. 2. Connect the other end of the cable to the OPTCAL IN Jack on the rear of unit as illustrated below: AU X I N 1 DC AU X I N 2 OPTICAL IN L DC IN 5.8V,1.5A R Optical Connection Cable TV OPTICAL OUT 3. Power on the unit and enter to Optical IN mode as previously instructed.
AUX IN 1: Listen music from RCA output jacks from an external Video/Audio Player such as a Television; DVD Player, VCR …etc. 1. Connect one end of the RCA Connection Cable (not included) to the AUX Out Jacks on the external Video/Audio Player. 2. Connect the other end of the cable to the AUX IN 1 Jacks on the rear of unit as illustrated below: AU X I N 1 DC AU X I N 2 OPTICAL IN L white DC IN 5.8V,1.5A R red Line out jacks of TV L R Video 3.
AUX IN 2: Listen music from an external Audio Player such as a MP3 Player, Discman …etc. 1. Connect one end of the Supplied Audio Connection Cable to the Line Out/AUX Out Jack on the external Audio Player. 2. Connect the other end of the cable to the AUX IN 2 Jack on the rear of unit as illustrated below: AU X I N 1 DC AU X I N 2 OPTICAL IN L DC IN 5.8V,1.5A R MP3 Player Mobile Phone Connect to the Phones; AUX Out; Line Out Jack of the external devices (Such like MP3 Player; cell phones; iPod/iPad ..
CLEANING: 1. To prevent fire or shock hazard, disconnect your unit from the AC wall outlet when cleaning. 2. The finish on your unit may be cleaned with a dust cloth and cared for as other furniture. Use caution when cleaning and wiping the plastic parts. 3. Mild soap and a damp cloth may be used.
GENERAL SPECIFICATION Power Source........................................................................................DC 5.8V, 1.5A, Audio Power................................................................................3W per Channel (Total 6W, RMS) BT Version...................................................................................................................................5.0 Bluetooth effective working range in open area............................................................
LIMITED WARRANTY Craig warrants this product to be free from manufacturing defects in material and workmanship under normal use for a period of 90 days from date of purchase. If service is required, please return the product to the store where it was purchased for exchange; or, pack the unit in the original packing material with all accessories if applicable, a copy of your sales receipt and a Cashier’s check or Money Order for $10 (to cover shipping and handling costs) payable to Craig Electronics Inc.
