INSTRUCTION MANUAL | MANUAL DE INSTRUCTIONES 10" (254 mm) Drill Press 10" (254 mm) Perforadora de columna CMXEDAR300 IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US. SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS. 1-888-331-4569 WWW.CRAFTSMAN.
English (original instructions) Español (traducido de las instrucciones originales) 1 21
English Definitions: Safety Alert Symbols and Words This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal injury or property damage. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
English 10" (254 mm) Drill Press CMXEDAR300 GENERAL POWER TOOL SAFETY WARNINGS WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE b) c) The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless) power tool.
English breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f ) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g ) Use the power tool, accessories and tool bits, etc.
English PROPOSITION 65 WARNING WARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to: www.P65Warnings.ca.
English and burning out of the motor. The table below shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. Make sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualified technician before using it. Protect your extension cords from sharp objects, excessive heat and damp or wet areas.
English CARTON CONTENTS UNPACKING YOUR DRILL PRESS Unpacking And Checking Contents Carefully unpack the drill press and all its parts, and compare against the list below and the illustration below. Place the drill press on a secure surface and examine it carefully. WARNING: To avoid injury from unexpected starting or electrical shock, do not plug the power cord into a source of power during unpacking and assembly. The cord must remain unplugged whenever you are adjusting/assembling the drill press.
English WARNING: Many illustrations in this manual show only portions of the drill press. This is intentional so that points being made in the illustrations can be highlighted. Never operate this drill press without all guards securely in place and in good operating condition. ASSEMBLY AND ADJUSTMENTS Estimated Assembly Time: 25-35 Minutes.
English Installing The Chuck (Fig. L, M) Fig. H 30 6 1. Fig. I 2. 31 32 15 3. Installing The Head (Fig. J) WARNING: The Drill Press head is very heavy and MUST be lifted with the help of 2 people OR MORE to safely assemble the Drill Press head on the column. 1. Carefully lift the head 33 and slide it onto the column 19 . Make sure the head 33 slides down over the column as far as possible. Align the head with the base. 2.
English Removing The Chuck (Fig. M) Adjustments Instructions 1. Turn the feed handles to lower the chuck to the lowest position. 2. Place a ball joint separator (not shown) above the chuck and tap it lightly with a hammer or rubber mallet to cause the chuck to drop from the spindle. CAUTION: Never hit the chuck directly with the hammer or rubber mallet. CAUTION: To avoid possible damage to the chuck, raise the jaws all the way first and be prepared to catch the chuck as it falls.
English 2. Turn the screw 42 clockwise to eliminate the play, using a slotted screwdriver, but without obstructing the upward movement of the spindle. (A little play in the spindle is normal.) 3. Tighten the lock nut 41 . Fig. Q Belt Tension (Fig. S) 1. 2. 3. 41 4. 5. 42 Quill Return Spring (Fig. R) The quill return spring may need adjustment if the quill return speed is too fast or too slow. This spring is located on the left side of the drill head. 1. Lower the table for additional clearance. 2.
English OPERATION Basic Drill Press Operation WARNING: To avoid possible injury, keep guard closed and in place while tool is in operation. To avoid injury from an accidental start, ALWAYS make sure the switch is in the “OFF” position, the switch key is removed, and the plug is not connected to the power source outlet before making belt adjustments. 3. To lock the switch in the OFF position, grasp the sides of the safety key, and pull it out. 4.
English Fig. X Fig. Z 1 59 58 37 56 57 53 Drill a Hole 54 Drilling To a Specific Depth Drilling a blind hole (not all the way through workpiece) to a given depth can be done two ways: Workpiece Method (Fig. Y, Z) 1. Make the depth mark 55 of the hole on the side of the workpiece. 2. With the switch “OFF”, bring the drill bit 54 down until the tip is even with the mark 55 . 3. Hold the feed handle at this position. 4. Spin the lower nut 56 down to contact the depth stop lug 57 . 5.
English Feeding Fig. AA 54 19 20 1. Pull down the feed handles with only enough effort to allow the drill bit to cut. 2. Feeding too slowly might cause the drill bit to burn. Feeding too rapidly might cause the belt or drill to slip, tear the workpiece loose or break the drill bit. 3. When drilling metal, it is necessary to lubricate the drill bit tip with oil to prevent burning of the workpiece and bit. 60 Fig. BB Tilting The Table (Fig. CC) 1.
English MAINTENANCE WARNING: For your own safety, turn the switch off and remove the plug from the power source outlet before maintaining or lubricating your drill press. General Maintenance Frequently blow out dust and grit that accumulates in the motor housing using compressed air. WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT: • ANSI Z87.1 eye protection (CAN/CSA Z94.
English TROUBLESHOOTING GUIDE BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS For assistance with your product, visit our website at www.craftsman.com for a list of service centers, or call CRAFTSMAN at 1-888-331-4569. PLEASE READ THE FOLLOWING: The manufacturer and/or distributor is providing the buyer with a parts list and assembly diagram in this manual as a reference tool only.
English Register Online Three Year Limited Warranty Thank you for your purchase. Register your product now for: • WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty service in case there is a problem with your product. • CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft, your registration of ownership will serve as your proof of purchase.
English PARTS LIST 10" (254 mm) Drill Press Parts list for drill press I.D. NO. Description I.D. NO. Description Size X759 BATTERY 2 X77L CR. RE. COUNT HD. SCREW M6*1.0-12 X75A SWITCH BASE 1 X77M CLAMP CORD X75C POWER CORD X75N HEX BOLT X75Q RACK X75T HEX BOLT Size Q’ty Q’ty 5 3 1 X77N CR. RE. COUNT HD. SCREW M8*1.25-25 3 X7AZ BATTERY BOX ASS’Y M5*0.
English 10" (254 mm) Drill Press Schematic for drill press X83N X84C X77K X84B X83G X77A2 X83H X77N3 X77M3 X83Z X83P X848 X7B8 X83R X77L4 X83F X77J2 X83L X83M X77B X77C X77L X77D4 X847 X846 X7792 X77N2 X75C X77H X77E X84C2 X778 X773 X7AZ X76L X774 X77N2 X76K X76S2 X76J X772 X84C X76M X83S X7712 X76H X7702 X77N X75A X7B7 H.
