Operator's Manual CRRFW HRH ° 6" and 8" BUFFER Model No. 351.226250 351.211812 CAUTION: Read and follow • • • • • • all Safety Rules and Operating Instructions before First Use of this Product. Keep this Manual with Tool. Sears, Roebuck and Co., Hoffman www.sears.com/craftsman 23984.01 Draft (06/26/06) Estates, IL 60179 U.S.A.
• Work area should be properly lighted. Warranty ......................................... 2 Safety Rules ...................................... 2 Assembly ........................................ Installation ...................................... • Proper electrical receptacle should be available for tool. Three prong plug should be plugged directly into properly grounded, three-prong receptacle.
• Refer to Figure 3, page 6. GROUNDING CAUTION: Do not attempt assembly if parts are missing. Use this manual to order replacement parts. • Check with a qualified electrician if grounding instructions are not understood or if in doubt as to whether the tool is IMPORTANT: Do not attempt assembly if parts are missing. Use this manual to order replacement parts. BUFFING INSTRUCTIONS WARNING: Improper connection of equipment grounding conductor can result in the risk of electrical shock.
SPECIFICATIONS (A 3-prong to 2-prong grounding adapter is not permitted in Canada.) Where permitted, the rigid green tab or terminal on the side of the adapter must be securely connected to a permanent electrical ground such as a properly grounded water pipe, a properly grounded outlet box or a properly grounded wire system. MODEL 226250 6" BUFFER The buffer is assembled with motor and wiring installed as an integral part of the tool.
• The threads on the right side of the buffer (facing unit) are right hand; threads on the left side are left hand. Hold the wheels firmly to loosen the hex nut. • Replacement 3450 RPM. wheels must have a minimum rated speed of • Make sure hex nuts are tight and snug against the outer wheel flange prior to restarting buffer. • Maximum wheel diameter for Model No. 226250 is 6" and for Model No. 211812 is 8".
Models 351.226250 Figure 3 - Replacement Parts Illustration and 351.
KEY NO. 1 PART NO. FOR: 6" 226250 00064.00 1 8" 211812 DESCRIPTION i 1/2"-12Hex Nut (LH Thread) QTY. 1 00088.00 5/8"-11Hex Nut (LH Thread) 1 2 23754.00 00089.00 Wheel Flange 4 3 24545.00 23985.00 2 4 STD840508 STD840508 Spacer 5-0.8mm Hex Nut* 5 STD551210 STD551210 #10 Serrated Washer* 3 6 24546.00 23986.00 Endshield 2 7 STD315225 i 6202ZZ Bearing* 2 STD315245 7 4 24547.00 23987.
PULIDORA • de 6"y 8" PRECAUCION: Lea y siga todas las Reglas de Seguridad e Instrucciones de Operaci6n antes de utilizar este producto por primera vez. Mantenga este manual junto con la herramienta. ............................................ Ilustraci6n Garantia Reglas 8-9 ............................................ 9 ....................................... 9-11 Operaci6n ......................................... 11 ....................................
• Nunca deje desatendida una herramienta Desconectela y no abandone detenido por completo. en funcionamiento. • el lugar hasta que se haya • • No trate de alcanzar equilibrado. demasiado lejos. Mant6ngase firme y • Nunca se pare sobre la herramienta. Se pueden producir lesiones graves si la herramienta se vuelca o hace contacto con la correa o el disco. Conozca su herramienta. Aprenda a manejar su aplicacidn y limitaciones especificas.
• • Revise periddicamente los cordones de la herramienta y si estAn daSados, Ilevelos a un centro de servicio autorizado CONEXIONES para que los reparen. las conexiones electricas. AsegQrese que la herramienta est6 apagada y desconectada de la fuente de alimentaci6n mientras monte, conecte o vuelva a conectar el motor o mientras inspeccione el cableado. El conductor verde (o verde y amarillo) del corddn es el cable de conexidn a tierra.
TAMANO DE LAS RUEDAS Di_.metro ........................................... 6" Di_.metro interior %" .................................... DESCRIPCION de 6" est,. equipada con un motor de voltaje puedan motor. Io cual permite presionar Las ruedas de repuesto deben dad nominal de 3450 RPM • El m_.ximo di_.
Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourse If. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME Call anytime, ® (1-800-469-4663) day or night(U.S.A, www.sears.com and Canada) www.sears.
