OPERATOR'S MANUAL 318 in. DRILL-DRIVER VARIABLE SPEED/REVERSIBLE Model Nos, 315.115340 -12 Volt 315,115350 -14,4 Volt _, WARNING: To red_)cethe risk of in}ury, the L_Se_ must read and understandthe operator's manual before using this product. Customer Sears, Help Line: 1-800-932-3188 Roebuck V'_it the Craftsman 983000-709 5-05 and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA web page: www.sears.
• Warranty .......................................................................................................................................................................... • Introduction ......................................................................................................... • 2 ............................................................ 2 GenaraJ S_.fetyRules.....................................................................................................................
• Do not overreach. Keep proper footing and balance at all 5rues. Proper foo_ng and ba_nce enable be_er cOnLTO[ of the tool in unexpected situations. • Use safety equipment. Nwaye wear eye protection. Dust mask, non-skidsafety shoes, hard hat, or hearing protectionmust be used for appropriate conditions. • Do notwear loose clothing or jewelry. Contain long hair. Looseclothes, jewelry, or long hair can be drawn into ah"vents. • Do not use on a ladder or unstable support.
SERVICE • Tool service must be performed only by qualified repair personnel. Service or maintenance performed bY ur_uaI_fisd per_nnel may resu{t {n a risk of Inju_. • Hold tool by insulated gripping surfaces when performing en operation whore the cutting tool may contec_thidden _rlng. Contact with a "tire" wire wi_ also make exposed metal parts of the tool "live" and shock the operator. • Know your power tool. Read operator's manual carefully.
'_ • a. That pins on plug ofextension cord _re the same number, size and shape as those of plug on charger. Before using battery charger, read all instructions end cautionarymarkings in this manual, on battery charger, battery, and produ_ using battery to prevent misuse of the productsand possibleinjury or damage. _IL • could resultin a risk of fire and electric shock, ff extensioncord must be used, make sure: WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS.
Some of the following symbols may be used on this tool. Please study them end learntheir meaning. Proper interpretation of these symbolswfl[allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperss Current Hz Her_. Frequency (cycles per second) W Watt Power min Minutes Time AlterrmtingCurrent Type of current -.
Thefollowing signalwords and meaningsare intendecLto expl_n the levels of risk associated with this product. SYMBOL _k SIGNAL MEANING DANGER: Indicates an imminentlyhazardous situation,which, ff not avoided, will resultin death or serious injury. WARNING: Indicates a potentially hazardoussituation, which, ff not avoided, could result indeathor serious injury. CAUTION: indicates a potantialtyhazardous situation,which, if not avoided, rnay resuffin minor or moderate injury.
PRODUCTSPECIFICATIONS MODELNO.315.t15340 Chuck .......................................................... 3/8 in. Keyless Motor .................................................................. 12 Volt DC MODEL NO. 3t5.t15350 Chuck .......................................................... 3/8 in. Ksyles= Motor .................................................................. 14 Volt DC Switch.......................................................... Variable Speed No Load Speed ........................
KNOWYOURDRILL-DRIVER See Figure 1. Before attempting to use this product, familiarizeyourself with all operating features and safety rules. BIT STORAGE LED WQRKLIGHT The LEDworPJight,located on the front of the tool base, illuminateswhen the switch _'iggar ts depressed.This providesextra light for inoreased yisibility. LEVEL Bits provided with the drill-drivercan be placed in the storagearea, located on the base of the drill.
• _1_ WARNING: Do not allow famiSa_tywith tools to make you careJess.Remember that a careless fracbon of a second is sufficientto intiict serious ]njury. _k Press down on b_ttsry pack to be'sure contacts on battery pack engage properlywith contacts in charging stand. • The charge indicator light (LED), located on the charging stand, wi_ I'_ghtup red and glow when the eharger is properly connected to power supply. "Thislight indicates the charger is operating property.
BATTERY PACK SHOWN INCHARGER TO REMOVEBATTERY PACK CI'.I_GING ASSEMBLY See Figure3. • Lock the switch triggeran the drill by placingthe direction of rotation selectorin the center position. • Locate the latcheson the side of the battery pack and depress to releasethe battery pack fTomthe drill. Remove the battery pack from the drill. • REDLED ORANGELED CHARGING STAND Fig. 2 TO INSTALL BATTERY PACK See FTgure3.
A WARNING: 6artery tools are a(ways in operatirtg conditfon. Therefore, the switch should always be locP.ed when not in use or carrying at you_" side. SWITCH TRIGGER See Rgure 4. To turn the driJlON, depress the switch trigger.To turn it OFF, release the switch trigger. VARIABLE SPEED See F/gum 4. The variable speed switch triggerdelivers higher spee(J and torque wi_ increased _gger pressureand lower speed with decreased trigger pressure.
ADJUSTABLE TORQUE CLUTCH LED WORKLIGHT See F/gum 7. The drill ls equipped with an adjustable torque clutch for driving different types of screws into differentmaterials. The proper setting depends on the type of material and the size of sorew you are using. The LED workJighton the foot of the drillwill come on when the switch _'igger ie depressed.This providesadditional lightingon the surface of the workpieoefor operaLion in lower-lightareas. ADJUSTING TORQUE See Ftgure 6.
INSTALLING BITS F/gure 9. _k • Lock the switch trigger by piecing the direction of rotation selector in the center position. • Open or close the chuck j_zwsto a point where the opening Lsalight/largar then the bit elze you intend to use. Also, raise the front of the driftstighttyto keep the b_ from fa_ling out of the chuck jaws. • Insert the drill bit straight into the chuck the full length of the jaws. • Tighten the chuck jaws on the drill bit. DRILLBIT UNLOCK .
'_ LEWL WARNING: Alwayswsar safety goggles or safety glasseswith aide shields when operating tools. Failure to do so could resultin objects being throwninto your eyes, resultingin possibleseriousinjury. DRILLING See Figure 11. A level is located on top of the motor housing to help keep the drill bit level during use. • Check the direction of rotation selector for the correct sathng (forward or raverae).
_I_ WARNING: When servicing, use on3yidentical Craftsman replar.sment parts. Use of any other paTt may create a hazard or cause product damage. CHUCK REMOVAL See F-_ums 12- 14. The chuci( may be removed and replaced bye new one. • _k WARN|NG: Always wear safety goggles or safety gta.sesswith side shields when using compressed air to clean tools. ITthe operation is dusty,siso wear a dust mask. Lock the switch triggerby placing the directionof rotation selector in center position. • |nsert a 5116 in.
• Insert the hex key into the chuck and tighten the chuck jaws sacurety.Tap sharplywith a m_et in a counterclockwise d_rection.This wilt loosenthe chuck on the BA'rrERIES The battery pack for this tool is equipped with nickel-cadmium rechargeabiebatteries. Length of servicefrom each charging willdepend on the type of work you are doing. spindle. It can now be unscrewed by hand. The batteriesin this tool have been designed 10 provide maximum b-ouble-frse life.
_- CRAFTSMAN 12 VOLT DRILL-DRIVER - MODEL NUMBER 315,115,340 -.----.--ii number [nall correspondence regarding yourDRILL-DRIVER orwhen ordering repair parts, The model number w([[ ba found on a plats attachedtothemotor housing. Alwaysmentionthemodel SEE BACK PAGE FOR PARTS ORDERING J | INSTRUCTIONS 2 1 \ 4 5 \ PARTS LIST Key No. Part Number 1 2 3 4 5 6 6612001 6903326 9,;0237076 140302002 130139017 300912192 983000709 DesQription Qty. Chuck Screw .........................................
CRAFTSMAN 14A VOLT DRILL-DRIVER - MODEL NUMBER 315.1t5350 I number in artcorrespondence regarding your DRILL-DRIVER or when ordering repair parts. the model J The model number will be found on a plate attached to the motor housing. Always mention SEE BACK PAGE FOR PARTS ORDERING | INSTRUCTIONS 2 1 \ 5 \ PARTS LIST Key No. Part Number 1 2 3 4 5 6 6612001 6903326 940237074 140302003 13O139014 300912193 983000709 Oescription Qty. Chuck Screw ............................................ ....
Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold PJ For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME ® (l-_o-4ss-4ss3) Call any'dine, clay or night (U.S.A. www.sears.com and Canada) www,seal_.
