Operator's Manual iPRO FESSiO HAL i PROFESSIONAL 1/2 in., 14.4 VOLTS CORDLESS DRILL-DRIVER Variable Speed / Reversible Model No. 315.267380 Save this manual for future reference • Safety • Features • Assembly • Operation •, Maintenance • Parts List CAUTION: Read and follow all Safety Rules and Operating Instructionsbefore first use of this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Visit the Craftsman web page: www.sears.
• Warranty ......................................................................................................................................................................... 2 • Introduction ..................................................................................................................................................................... 3 • General Safety Rules ....................................................................................................................
Yourdrill-driverhasmanyfeaturesformakingyourdrilling operations morepleasantandenjoyable.Safety, performance anddependability havebeengiventop priorityinthedesignofthisdrill-drivermakingiteasyto maintainandoperate. _. _k Work Area Personal Safety • Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication.
Tool Use and Care • Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. • Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control. • Do not force tool. Use the correct tool for your application.
• Neverusea batterythat hasbeendroppedor receiveda sharpblow. A damaged battery is subject to explosion. Properly dispose of a dropped battery immediately. Failure to heed this warning can result in serious personal injury. • Save these instructions. This manual contains important safety and operating instructions for charger. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.
Important:Some interpretation of the following symbols may be used on your tool. Please study them and learn their meaning. Proper of these symbols will allow you to operate the tool better and safer.
PRODUCT DRILL-DRIVER SPECIFICATIONS: 315.267380 CHARGER Item No. 9 11040 (981399-001) 120 V, 60 Hz, AC only 9.6 - 24 Volt t Hour Chuck 1/2 in. Keyless Motor Gear Train DC Motor 14.4 Volt Input Charging Voltage Switch Two Speed Variable Speed Charge Rate No Load Speed 0-350/min. Clutch 0-1200/rain. (High) 24 Positions Maximum Torque 320 in.lb. KNOW YOUR (Low) DRILL-DRIVER See Figure 1.
YELLOWLIGHT"ON" ANDRED LIGHTFLASHINGINDICATES DEFECTIVEBATTERYPACK TORQUE ADJUSTMENTRING CHARGER ) SPEED GEARTRAIN(HI-LO) DIRECTIONOF ROTATIONSELECTOR (FORWARD/REVERSE) KEYLESS CHUCK GREENLIGHT"ON" INDICATESFULLY CHARGEDANDSLOWCHARGING TO MAINTAINBATTERYPACK REDLIGHT"ON" INDICATES FASTCHARGINGMODE SCREWDRIVERBITS BATI'ERYPACK WRISTSTRAP Fig. 1 CHARGER See Figure 2. Your charger has a "key hole" hanging feature for convenient, space saving storage.
AUTO-SPINDLELOCK ,_WARNING: Make sure to insert drill bit straight into chuck jaws. Do not insert drill bit into chuck jaws at an angle and then tighten, as shown in Figure 4. This could cause drill bit to be thrown from drill, resulting in possible serious personal injury or damage to the chuck. Your cordless drill has an auto-spindle lock. This feature makes installing and removing bits much easier. When the switch trigger is released and the motor comes to a complete stop, you may hear a click.
TO A'I-rACH BAI-I'ERY PACK TO DRILL TO REMOVE See Figure 6. See Figure 5. Note: Battery pack is shipped in a low charge condition. Therefore, it must be charged prior to use. Refer to page 11, "CHARGING BATrERY PACK" for charging instructions. • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 10. • Align raised ribs on battery pack with grooves on bottom of drill, then attach battery pack to drill as shown in Figure 6.
,_. If after one hour red light is still flashing, this indicates a defective battery pack and should be replaced. WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. CHARGING BA'n'ERY Green light on indicates battery pack is fully charged and slow charging to maintain battery pack. Yellow light on and red light flashing indicates defective battery pack.
SWITCH SWITCH See Figure 8. See Figure 10. LOCK TO turn your drill ON, depress the switch trigger. To turn it OFF, release the switch trigger. The switch trigger can be locked in the OFF position. This feature can be used to prevent the possibility of accidental starting when not in use. To lock switch trigger, place the direction of rotation selector in center position. SELECTORWITH REVERSE CENTERLOCK POSITION SWITCHTRIGGER VARIABLE f Fig. 8 SPEED FORWARD Fig.
KEYLESS ADJUSTABLE CHUCK See Figure 11. CLUTCH Your drill is equipped with an adjustable torque clutch for driving different types of screws into different materials. The proper setting depends on the type of material and the size of screw you are using. A keyless chuck has been provided with your drill to allow for easy installation and removat of bits. As the name implies, you can hand tighten or release drill bits in the chuck jaws.
,_ When drilling hard smooth surfaces use a center punch to mark desired hole location. This will prevent the drill bit from slipping off center as the hole is started. However, the low speed feature allows starting holes without center punching if desired. To accomplish this, simply operate your drill at a low speed until the hole is started. The material to be drilled should be secured in a vise or with clamps to keep it from turning as the drill bit rotates.
CHUCK Insert hex key in chuck and tighten chuck jaws securely. Tap sharply with a mallet in a counterclockwise direction. This will loosen chuck on the spindle. It can now be unscrewed by hand. See Figure 16. REMOVAL See Figures 14, 15, and 16. The chuck must be removed in order to use some accessories. To remove: • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 10.
,_ Do not abuse power tools. Abusive practices can WARNING: When servicing use only identical Craftsman replacement parts. Use of any other parts may create a hazard or cause product damage. damage tool as well as workpiece. Only the parts shown on parts list, page 17, are intended to be repaired or replaced by the customer. All other parts should be replaced at a Sears Service Center. Avoid using solvents when cleaning plastic parts.
CRAFTSMAN I 1/2 in. PROFESSIONAL CORDLESS MODEL NO. 315,267380 DRILL-DRIVER The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your CRAFTSMAN 1/2 in, PROFESSIONAL CORDLESS DRILL-DRIVER or when ordering repair parts. SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS 2 5 PARTS Key No. Part Number Description LIST Qty. 1 975379-000 Screw (Special) ...................................................................
Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME Call anytime, ® (1-800-469-4663) day or night (U.S.A. and Canada) www.sears.com www.sears.
