Operating instructions

TOOLS REQUIRED
o Slotted and Phillips screwdriver.
, Small or medium sized adjustable wrench
(or a set of nutdrivers).
• Hammer•
ROUTER TABLE
1. Lay the router table, top down. on a flat surface so
that the orientation of the table is as shown in Figure 1.
(BACK of the table is facing toward you.)
FIGURE 1
- qOb-Eq
TABLE /-_ "!0 32 X 1 2" LONG
! LEG J TRUSS HEAD MACHINE
/_
SCREW (TYPICAL!
_J
_I0 32 HEX KEPS bIUT
•" _ {TYPICALI
.... _ _. L_'-'..__, .... j÷ i'
1
/
BACK C:-
ROUTER -&BLE
2. Assemble a table leg to the table top using four
#10-32 x 1/2" long truss head machine screws and
four #10-32 hex "KEPS" nuts, as shown in Figure 1
and the Figure t, Assembly Detail. (Leg is shown in
the UPPER LEFT corner of router table.) DO NOT
TIGHTEN at this time.
3. Position the switch against the leg, as shown in
Figure 1, Assembly Detail.
4. Secure the switch to the leg and table top using
two #10-32 x 1/2" long truss head machine screws,
and two #10-32 hex "KEPS" nuts.
FIGURE 1, ASSEMBLY DETAIL
_ 10 32 X 1,2" LONG
TRUSS HEAD MACHINE
=/ SCREW ITYPICAL)
' \ -- ROUTER TABLE
ROUTER /!\ \ . _ -- ,10 32 HEX "KEPS" NUT
TABLE LEG _-- _ _ ' ITYP!CALI
MACHINE _ ---=- _ ...... :;-, . - {, "-
SCREW NUT "_ _'7;_" "_-1"> ' : ":
(TYP CALl _ * - _ :" = -" " _ ....
f_
ASSEMB:_ v DETA'L
] There are two hex shaped
]
NOTE
recesses in the switch case into which the hex
"KEPS" nuts are placed, with the toothed washer
side of the nuts facing out of the recesses.
5. Securely TIGHTEN all fasteners.
6. Assemble the remaining three table legs to the
table top using four #10-32 x 1/2" long truss head
machine screws and four #t0-32 hex "KEPS •' nuts
for each leg, as shown in Figure 2. (The BACK of
the table is facing toward you.)
7. Securely TIGHTEN all fasteners.
FIGURE 2
SWITCH
'\ RO_,-SR --
T&BLE
_--=I032 _E_ KEU5
" _--<---- " E_ _..'--" .... 7 :,_,/_ >_UT -"=C'-
. '" DE,.
....1...---.:, °
__ -- _10 32 X 1 2 LD_4G
ROUTER
&
BACK OF TABLE TRUSS HEAD ),!ACHtNE
ROUTER TABLE LEG
SCREW T'r clCAL;
EXTENSIONS TO THE ROUTER TABLE
1. Position the router table so that the orientation is
as shown in Figure 3 and Figure 3, Assembly Detail.
(FRONT of the table is facing toward you.)
2. Position one of the extensions alongside the right
side of the table top so that the miter slot in the
extension lines up with the miter slot in table top.
3. Assemble a #10-32 x 1/2" long truss head
machine screw and a #10-32 hex "KEPS" nut at
each of the holes in the extension, as shown in
Figure 3 and Figure 3, Assembly Detail. DO NOT
FIGURE 3
_10 32 _EX KEPE !;_jT -- -- ROL'-En -- "10 32 X _ 2 LONG
ITYI_IB ALl
,+ -*t. RLE _EG TRUSS HEAD &4,mCHI_4E
--_ \ c- -
\ SCREW +TY_!CAL ,
/_ RIGHT SIDE
..... _' / EXTENS!ON BR_CE
• ,_ f',.":--r---,_ .... ,_ __- "-
EXTE tiSIOt't
,' " L. _ 'L --
__ __"- ...... -_L.-'-t--
/_ EXTENSIOn, BRACE
/ \_ '_ ,10 32 HEX KECE
ROUTER _-- S\%ITCH -- %, NUT INOT _lS BLEI
TABLE _'1032X 12 LONG
'10 32 HEX "KEPS --z TRUSS HEAD MACHI_4E
NUT _NOT _ IE!BLE SCRE','v Ib_OT VfSfBLE