Owner’s Manual 8-in. Wheel 3/4 Horsepower (continuous duty) 3450 R.P.M. (no load speed) 8-in. BENCH GRINDER Model No. 152.220180 10-in. Wheel 1 Horsepower (continuous duty) 1725 R.P.M. (no load speed) 10-in. BENCH GRINDER Model No. 152.220600 CAUTION: ® C US FOR YOUR OWN SAFETY; Read and follow all of the Safety and Operating Instructions before Operating this Bench Grinder Customer Helpline 1-800-897-7709 Please have your Model No. and Serial No. available. Sears, Roebuck and Co.
TABLE OF CONTENTS PAGE SECTION Warranty ..........................................................................................................................................................................2 Product Specifications...................................................................................................................................................2 Safety Instructions .............................................................................................................
! WARNING To avoid electrical shock to yourself and damage to the Bench Grinder, use proper circuit protection. and use a 15 amp time delay fuse or circuit breaker. The electrical circuit cannot have any wire size less than #14. To avoid shock or fire, replace power cord immediately if it is damaged in any way. The Bench Grinder is factory wired for 120V, 60 Hz, operation. Connect to a 120V, 15 amp branch circuit SAFETY INSTRUCTIONS GENERAL SAFETY INSTRUCTIONS 8. WEAR PROPER CLOTHING.
SAFETY INSTRUCTIONS 17. DO NOT STAND ON A TOOL. Serious injury could result if the tool tips over or you accidentally contact the tool. (cont.) 26. CALIFORNIA PROPOSITION 65 SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING AND OTHER CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm. 18. DO NOT store anything above or near the tool where anyone might try to stand on the tool to reach it. 19. MAINTAIN YOUR BALANCE.
GROUNDING INSTRUCTIONS IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides the path of least resistance for electric current and reduces the risk of electric shock. This tool is equipped with an electric cord that has an equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching electrical receptacle that is properly installed and grounded in accordance with ALL local codes and ordinances.
SPECIFIC SAFETY INSTRUCTIONS FOR BENCH GRINDERS 3. THE DIAMETER OF THE GRINDING WHEELS WILL DECREASE WITH USE. Adjust the tool rests and spark arrestors to maintain a distance of 1/16” from the wheel. The operation of any grinder can result in debris being thrown into your eyes, which can result in severe eye damage. ALWAYS wear Safety Goggles (that comply with ANSI standard Z87.1) when operating the grinder. Safety Goggles are available at Sears Retail Stores.
CARTON CONTENTS UNPACKING AND CHECKING CONTENTS (Fig. C) Bench Grinder can only be turned “ON” after all the parts have been obtained and installed correctly. This Bench Grinder will require a minimal amount of assembly. A 10mm and 13mm open end wrench is provided for mounting the Tool Rest Assemblies and the Spark Arrestor Assemblies. The following items are to be provided in the shipping box: Remove all of the parts from the shipping box and lay them on a clean work surface. Compare the items to Fig.
KNOW YOUR BENCH GRINDER 6 7 4 3 1 5 10B 10A 9 2 11 8 14 13 1. WHEEL GUARD - Covers the grinding wheels and protects against accidental contact. 10. B) GRINDING WHEEL 60 GRIT - Used to remove heavy material from workpiece. 2. WHEEL COVER - Covers the grinding wheels and provides access for routine maintenance. 11. ON / OFF SWITCH - Used to turn “ON” and turn “OFF” the grinder. 3. MOTOR HOUSING - Contains the electrical motor. 12.
ASSEMBLY INSTRUCTIONS Fig. E A 10mm and 13mm open-end wrench (included) is required for assembly of the Tool Rest Assemblies and the Spark Arrestor Assemblies. ! WARNING • DO NOT assemble the Bench Grinder until you are sure the tool IS NOT plugged in. • DO NOT assemble the Bench Grinder until you are sure the power switch is in the “OFF” position. • DO NOT assemble the Bench Grinder until you are sure the grinding wheels are firmly tightened to the Bench Grinder. E H F G TOOL RESTS (Figs.
EYE SHIELDS (Fig. G) WORK LIGHT (Fig. H) The Bench Grinder is provided with a Flexible Work Light to assist in visibility of the workpiece. 1. Remove both Eye Shield Assemblies from the plastic bags and check to see that you have the following. Eyeshield (qty. 2) Lock Knob (qty. 2) Spacer (qty. 2) M6 Flat washer (qty. 2) M6 x 80mm carriage head screw (qty. 2) The Bench Grinder is NOT provided with a light bulb for the Flexible Work Light. ! 2.
OPERATING THE BENCH GRINDER USING THE WHEEL DRESSER (Fig. J) The Bench Grinder is designed for hand held grinding, sharpening, and cleaning operations. Fig. J ALWAYS WEAR EYE PROTECTION! Hot sparks are produced during grinding operations. 1. The Power Switch must be in the “OFF” position. 2. Stand to the side of the Bench Grinder and plug in the power cord to the correct power source. 3. Remain to the side of the Bench Grinder and turn it “ON” by moving the power switch to the up position. 4.
CHANGING THE GRINDING WHEEL (Fig. K) Fig. K D C J F K I B A G H E 1. Turn the power switch “OFF” and unplug the power cord from its power source 8. CAUTION: The new abrasive wheel to be put on the Bench Grinder must have a higher R.P.M rating than the Bench Grinder. The label on the side of the abrasive wheels must stay on, DO NOT remove this label. 2. Rotate the eyeshields to the “UP” position for access to the tool rests. 9.
MAINTENANCE OF THE BENCH GRINDER ! CAUTION: REPLACE the abrasive wheels if there is any damage at all. FAILURE to replace a damaged wheel can cause serious injury to the operator. WARNING Turn the power switch “OFF” and unplug the power cord from its power source prior to any maintenance. CAUTION: DO NOT USE FLAMMABLE MATERIALS to clean the Bench Grinder. A clean dry rag or brush is all that is needed to remove dust and debris buildup.
PARTS 8-IN. PROFESSIONAL BENCH GRINDER PARTS LIST ! MODEL NO. 152.220180 WARNING When servicing, use only CRAFTSMAN replacement parts. Use of any other parts may create a HAZARD or cause product damage. ! WARNING Any attempt to repair or replace electrical parts on this Bench Grinder may create a HAZARD unless repair is done by a qualified service technician. Repair service is available at your nearest Sears Service Center. Always order by PART NUMBER, not by key number. KEY NO. PART NO.
8-IN. PROFESSIONAL BENCH GRINDER PARTS LIST MODEL NO. 152.
PARTS 10-IN. PROFESSIONAL BENCH GRINDER PARTS LIST ! MODEL NO. 152.220600 WARNING When servicing, use only CRAFTSMAN replacement parts. Use of any other parts may create a HAZARD or cause product damage. ! WARNING Any attempt to repair or replace electrical parts on this Bench Grinder may create a HAZARD unless repair is done by a qualified service technician. Repair service is available at your nearest Sears Service Center. Always order by PART NUMBER, not by key number. KEY NO. PART NO.
10-IN. PROFESSIONAL BENCH GRINDER PARTS LIST MODEL NO. 152.
Get it fixed, at your home or ours! Your Home For repair – in your home – of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner’s manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME® (1-800-469-4663) Call anytime, day or night (U.S.A. and Canada) www.sears.
