Owner`s manual

Installation Step 7
Install the Door Control and
Connect all Wiring
Locate the door control within sight of the door at a
minimum height of 5 feet where small children cannot
reach, and away from all moving parts of the door and
door hardware.
The door control is typically attached directly to the wall.
If installing into drywall, drill 5/32" holes and use the
anchors provided. For pre-wired installations (as in new
home construction), Console models" may be mounted to a
standard single gang boa"(Figure 2).
1. Strip 1/4" of insulation from one end of the bell wire
and connect it to the two screw terminals on the back of
the door control by color: white to 2 and white/red to 1.
2. Pry off cover along one side with a screwdriver blade
(see Figurel). Fasten with 6ABxl-1/4" self-tapping
screws (standard installation) or 6-32x1" machine
screws _re-wired installation) as follows:
• Install bottom screw, allowing 1//8" to protrude above
wall surface.
• Position bottom of door control on screw head and
slide down to secure. Adjust screw for snug fit.
• Drill and install top screw with care to avoid cracking
plastic housing. Do not overtighten.
• Insert top tabs and snap on cover.
3. (For standard installation only) Run the bell wire up the
wall and across the ceiling to the opener. Use insulated
staples to secure the wire in several places. Be careful
not to pierce the wire with a staple, creating a short. If
your access door is near the garage dooz you may run
this wire with the SaJoty Reversing Sensor wires along
the top of the rail. Seepage 18.
4. Remove the Control Center door on the right panel of
the opener to access the terminal screws.
5. Thread all wires through the opening at the base of the
drive shaft cover (see Figure 3).
6. Insert the remaining wire through the hole in the power
unit and strip 1/4" of insulation from each set of wires.
7. Connect the door control wire to the opener terminal
screws: white to 2 and white/red to 1. (See Figure 4.)
8. Separate the sensor white and white/black wires
sufficiently to connect to the opener terminal screws:
white to 2 and white/black to 3.
9. Attach the User Safety Instruction label to the wall near
the door control, and the Maintenance Instruction label
in a prominent location on the inside of the garage door.
Page 32 explains how to operate the opener using the
door control.
Hardware Shown Actual Size
Control Console (std installation)
Control Console (pre-wired)
Insulated
Staples
Dry Wall Anchors
21
Do not connectto live electricalwiring. Connect onlyto 24Volt
low voltagewires. Connectionto live wires or higherv oltage
may causeseriousinjuryfrom shock,burnorelectrocution.
Childrenoperatingor playingwith a garage door openercan
injurethemselvesor others. Thegaragedoor oou/d o/oseand
causeseriousinjury ordeath.
Install thedoor control(or anyadditionalpushbuttons)outof
the reach of childrenand away from all moving parts of the
doorand door hardware,but where thegarage door is visible.
Do not allow children to operate the push b utton(s) or the
remotecontrol(s).
A movinggarage door couldinjuresomeoneunderit. Activate
the openeronly when the door is properly adjusted,you can
seeit clearly,andthere arenoobstructionsto doortravel.
Do NOT connect the power and operate the opener at
this time. See Step 9 on page 22.
STANDARD
CONTROL
CONSOLE
Lighted
Push
Button
Figure 1
REMOVE & REPLACE COVER
To Replace, _-----.....,_o Remove,
Inse rt _1_'_ Twist
Top Tabs _ _ ]]_ff[_' I Here
• //
'BACK VIEW
Figure 2
PRE-WIRED
INSTALLATION
Top
Mounting
Hole
Terminal
Screws
Bottom
Mounting
Hole
24 Volt
2-Conductor
Bell Wire
Figure 3
WIRING TO
CONTROLCENTER
Insert wires
through
opening in
Drive Shaft Cover
Push wiring
through hole in chassis
(above Control Center)
and connect to opener
terminal screws
Figure 4
Door Control Sensor
OPENER TERMINAL SCREWS
(In Control Center)