Owner`s manual
This warranty g Yes you specif c egal rights, and you may also have other rights which vary
from State to state; _
SEARSI ROEBUCK AND CO., DEPT. 69B/731A Sears ToWer. Chicago, IL 60684
Before =operating the Recreator read and understand your Router and Router Recreator
owner's manuals and affixed warnings.
The General Safety Instructions which follow apply to your Router and Router Recreator
co mbinaUon as a "power tool."
genera!l safety instructions for power tools
1. KNOW YOUR POWER TOOL
Read and understand the owner's manual and 12.
labels affixed to the tool Learn its application
and limitations as well as the specific potential
hazards peculiar to this tool.
2. GROUND ALL TOOLS UNLESS
DOUBLE INSULATED 13.
If tool is equipped with an approved
3-conductor cord and a 3--prong grounding
type pug to fit the proper grounding type
receptacle. The green conductor in the cord is
the grounding wire. Never: connect the green 14.
wire to a live terminal
3, KEEP GUARDS iN PLACE
and in working order.
4. REMOVE ADJUSTING KEYS
AND WRENCHES
Form habit of checking to seethat keys and 16.
adjusting wrenches are removed f,rom tool
before tui'ning it on. : i :- :
5; KEEP WORK AREA CLEAN : 17.
Cluttef;ed areas and benches nv te accidents.
Ftoor must not be slippery dueto wax: or
sawdust. --18.
6, AVOID DANGEROUS ENVIRONMENT
Don't use power tools in damp or wet location.
Keep work area well lit. Provide adequate
surrounding work space.
7. KEEP CHILDREN AWAY 19.
AH visitors should be kept a safe distance from
work area,
8. MAKE WORKSHOP KID-PROOF
-- with padlocks, master switches, or by
removing starter keys.
9. DON'T FORCE TOOL
It wit! do the job better and safer at the rate for
which it was designed.
10. USE RIGHT TOOL
Don't force tool or attachment to d oa job it was
not designed for.
WEAR PROPER APPAREL
No loose clothing, g oves, neckties or jewelry to
get :caught in moving, parts. Rubber-soled damaged should
footwear is recOmn_ended fop best footing replaced.
USE SAFETY GOGGLES
Safety goggles must comply with ANSI
Z87.1-t968, Also use face or dust mask if
cutting operation is dusty. Everyday
eyeglasses only have =mpact resistant lenses,
they are not safety glasses.
SECURE WORK
Use clamps or a vise to hold work when
practical, it's safe r than using your hand, frees
both hands to operate toot.
DON'T OVERREACH
Keep proper footing and balance at all ttmes.
15. MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for best and safest
performance. Follow instructions for
lubrication and changing accessories.
DISCONNECT TOOLS
before servicing; when changing accessories
Such as blades, bits, cutters, _tc.
AVOID ACCIDENTAL STARTING
Make sure switch is in "OFF position before
plugging in.
USERECOMMENDEDACCESSORIES
Consult the owner's manual for recommended
accessories. Follow the instructions that
accompany the accessories. The use of
tmprope_" accessories may cause hazards.
NEVER STAND ON TOOL
Serious injury could occur if the toot is tipped
or if the cutting tool is accidentally contacted.
Do not store materials above or near the tool
such that it is necessary to stand on the tool to
reach them.
20. CHECK DAMAGED PARTS
Before further use of the tool, a guard or other
part that is damaged should be carefully
checked to ensure that it will operate properly
and perform its intended function,
Check for alignment of moving parts, binding
of moving parts, breakage of parts, mounting,
and any other conditions that may affect its
operation. A guard or other part that as
be properly repaired or