Installation Guide
L’installation est simple comme bonjour!
PrŽparation du piŽdestal
a.
Pour installer
efficacement les potelets
montage sur colonne, utiliser le
gabarit de montage sur colonne
qui accompagne ce guide
dinstallation.
b.
Poser le gabarit sur la colonne
dŽsirŽe et marquer
lemplacement des trous de
montage (voir le gabarit inclus).
c.
Percer des trous de montage de
3,8 cm (1 1/2 po) de profondeur
laide dun foret bŽton de 5/16
po (pour pose sur les surfaces
en briques ou en bŽton) en
maintenant le conduit
Žlectrique centrŽ entre les deux
trous. Le conduit Žlectrique doit
avoir une hauteur libre de 7,5
cm (3 po). Pour une installation
sur des colonnes en bois, utiliser
des vis bois de 1 1/2 po.
d.
Pour une installation sur les
briques ou le bŽton, enfoncer
des chevilles en plastique
rous
percŽs (voir la Figure A).
Figure A
Instructions de montage
des potelets
extérieurs sur piédestal
Conduit
électrique
Chevilles
en plastique
ColonneGuide pour
piédestal
Trous de
5/16 po
Couper le courant
Toujours couper le courant au tableau Žlectrique ou dŽbrancher le fusible
lors de linstallation ou de la rŽparation de tout autre appareil Žlectrique.
LA PRSENCE
DE COURANT
PEU T CAUSER
DES
BLESSURES
GR AVES, VOIRE
MORTELLES
ATTENTION
–Outillage nécessaire–
・Tournevis Cruciforme
・Mastic
・Ampoules
・Foret de
5
/
16 po pour
colonnes en bŽton
ou ou
Caulk
Assemblage
Le temps de montage est de 35 minutes environ
Guide
E
18W/840
ou
IMPO RTANT! PLEASE READ:
All Craftmade solid brass and cast aluminum lanterns are prepared
with a durable lacquer finish or a powder-coated/painted finish.
Please note that the brass finish or painted finish on exterior lanterns will
weather or tarnish over time, depending upon the environmental conditions where the lantern is installed.
Your proper care of lanterns (see below) will enhance both the life and appearance of the lanterns. Post treatments,
such as clear lacquer, are not recommended.
PROPER CARE
In order to maximize the appearance of a Craftmade brass lantern, it is important that dust and debris is removed
from the surface of the lantern periodically. It is recommended that the lanterns be wiped down weekly using a
soft, dry or damp cloth.
DO NOT use any abrasives such as car wax, brass cleaners or other polishes, glass cleaners or chemicals, as this
will scratch/ remove/damage the protective coating, allowing moisture and pollutants to come in contact with the
brass, which will result in discoloration and pitting.
AL L Craftmade cast aluminum lanterns receive a durable powder coat finish, which enhances the durability of
the lantern. This finish should also be wiped down weekly with a soft, dry or damp cloth to remove the dust and
debris that will accumulate on the surface. DO NOT use any abrasives such as car wax, brass cleaners or other
polishes, glass cleaners or chemicals as this may damage the finish.
FAILURE TO FOLLOW THE ABOVE CARE INSTRUCTIONS WIL L VOID THE WARRANTY OF THE
LANTERN.
For information regarding replacement parts, please write to:
Craftmade, P.O. Box 1037, Coppell, TX 75019
LIMITED WARRANTY
Craftmade warrants against defects in materials or workmanship for a minimum of THREE (3) YEARS f rom date of
purchase for use, and agrees to repair or, at our option, replace a defective unit without charge. Brass finish is
covered 90 days from purchase date.
IMPO RTAN T: This Warranty does not cover damage resulting from accident, misuse or abuse, lack of reasonable
care (see above), the affixing of any attachment not provided with the product, alteration of any attachments
factory installed, loss of parts or subjecting the fixture to any but the specified electrical service. This warranty
does not cover failure of bulbs due to accidents, abuse, misuse, vandalism, power surges, and acts of nature such
as lightning damage or any bulbs purchased separately and installed by the consumer or any damage to the fixture
caused by a separately purchased bulb.
No responsibility is assumed for any special incidental or consequential damages. Damages occurring during
transit are not covered by this warranty.
To obtain warranty service, mail sales receipt as proof of purchase-date, and a brief explanation of the nature of
the defect, to P.O. Box 1037, Coppell, TX 75019. You will receive, by mail, a Return Goods Authorization number
issued by Craftmade, and returned freight prepaid.
For Installation or Technical Support, call 1-800-486-4892, 8 a.m. - 5 p.m., Central Time, Monday-Friday.
Please send the following information
1. The Model Number and Finish Polished, Antique,
White, etc.
2. The name of the part if you have a parts problem.
3. Your name, mailing address and phone number
(with area code).
f.
For screw on glass fixtures, unscrew glass counter
clock wise. Insert bulb(s) and screw glass back on
(see figure 7).
g.
Turn power on.
Figure 7
Screw on Top Glass Assembly
Glass
Twists
Off
Craftmade International Inc. ・ P.O. Box 1037 ・ Coppell, TX ・ 75019 ・ USA
4-2007Printed in China
If fixture does not work:
1. Turn off electrical power and check all wire connections.
2. Check fuse or circuit breaker and replace if necessary.
3. Check to make sure light bulb is in working order.
4. Ensure that dimmer switch is in the "on" position.
Troubleshooting
E4 F1