READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Windswept Installation Guide For Models: WND78 WND102 WND120 WARNING: DC Motor will not operate until blades are installed APPROVED FOR USE IN DAMP LOCATIONS net weight of fan: 37.48 lb (17 kg), WND78 39.68 lb (18 kg), WND102 41.89 lb (19 kg), WND120 Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Fan Assembly. pgs. 4 - 5 Wiring. pgs.
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2. 3. 4.
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. a b a. canopy. 1 piece b. hanging bracket. 1 piece c d c. downrod and hanging ball (with pin and clip). 1 piece d. motor housing. 1 piece e. yoke cover.
12ft. - 20ft. (3.66m - 6.1m) 3. Installation Preparation. blade edge 30 10 feet inches (3.05m) (76cm) To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 10 feet (3.05m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 400 square feet (37.2 square meters). 12ft. - 20ft. (3.66m - 6.
. Fan Assembly. stop pin set screw Remove hanging ball from downrod provided by loosening set screw on hanging ball. Remove pin and clip. Lower hanging ball and remove stop pin and then slide hanging ball off of the downrod. [Refer to diagram 1.] Loosen yoke set screws at top of motor housing. [Refer to diagram 2.
5. Fan Assembly. (cont.) wood ceiling joist With the hanging bracket secured to the outlet box and able to support the fan, you are now ready to hang your fan. Grab the fan firmly with two hands. Slide downrod through opening in hanging bracket and let hanging ball rest on the hanging bracket. Turn the hanging ball slot until it lines up with the hanging bracket tab.
6. Wiring. (cont.) [PLEASE NOTE: Wall and/or handheld remote control must be used for fan to operate. If you do not wish to use the wall control, please proceed to Section 7 below to continue with fan installation.] Modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment. *NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
. Blade Assembly. WARNING: To reduce the risk of serious bodily injury, DO NOT use power tools to assemble the blades. If screws are overtightened, blades may crack and break. hex nuts and washers Locate 18 blade attachment screws, 18 washers and 18 hex nuts in hardware pack. Place blade on TOPSIDE of one of the blade arms that extend from side of motor housing, aligning holes in blade with holes in blade arm as shown in diagram at right. Insert 1 blade attachment screw from underside of blade arm.
. Handheld Remote Control Assembly. (cont.) post hole Align holes in wall control with posts located on inside of TOP part of remote control cover and press together firmly. Place wall control into BOTTOM part of remote control cover, aligning posts in top of remote control cover with post holes in the bottom. [Refer to diagram 3.] (NOTE: Make sure to align narrower ends of remote control cover before closing.
. Automated Learning Process./Activating Code. (cont.) WALL CONTROL REMOTE CONTROL LED LIGHT FAN OFF LED LIGHT IMPORTANT Remote and wall controls must be SYNC R ONI E with fan in order to properly function. FAN OFF 3 FAN SPEED 2 1 4 5 6 REVERSE 3 4 2 1 5 FAN SPEED 6 REVERSE UP-LIGHT LIGHT KIT FACEPLATE BATTERY LED LIGHT: FAN SPEED, Buttons 1-6: REVERSE Button: UP-LIGHT: LIGHT KIT: FAN OFF: ON/OFF Slider Switch: ON/OFF SLIDER SWITCH Lights up when any button is pressed.
Troubleshooting. Warranty. WARNING: Failure to disconnect power supply prior to troubleshooting any wiring issues may result in serious injury. Problem: Fan fails to operate. Solutions: 1. Check power to wall switch/wall control. 2. Check to be sure code switches in remote control transmitter and wall control are set properly. 3. Verify that wall control is wired properly. 4. Check to be sure fan is wired properly. 5.
