Juna Ceiling Fan JU54 Installation Instructions Instrucciones de instalación Instructions d’installation
1 Read and Save These Safety Precautions 1. Turn off electricity at main switch before wiring or servicing fan in order to avoid possible electrical shock. 2. All wiring must be in accordance with the National Electric Code (ANSI/NFPA70-1999) and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3.
2 Before Assembly 1. Make sure that the fan voltage (120) is compatible with your own electrical system. 2. Check to make sure that your carton contains all the parts mentioned in the parts list. NOTE: The box can be used as a work space to prevent any damage on the ornamental surface. CAUTION: Before installing, choose a location for mounting the fan where the blades have at least 7 feet of clearance from all objects and floor. Mount an outlet box to the ceiling or use an existing box.
Quantity Screw Package S1. S2. S3. S4. S5. S6. S7. S8. S1 S2 2 2 10 7 3 1 1 1 Wood Screws & Washers Bracket Screws Blade Screws & Paper Washers Blade Arm Screws Wire Connectors Safety Bolt & Nut "J" Hook Zip Tie S3 S4 S5 S6 S7 S8 Tools You Need 1. Phillips Screwdriver 2. Adjustable Wrench 3. Flat Screwdriver 4.
3 Turn off circuit breakers and wall switch to the fan supply line leads. Preparation Important: When using an existing outlet box, be sure the box is securely attached to the building structure and can support the full weight of the fan. Failure to do so can result in serious injury or death. b.) Angle Mount 7BVMUFE $FJMJOHT B %PXOSPE .PVOU /PSNBM $FJMJOHT IMPORTANT: If using the angle mount method, check to make sure the ceiling angle is not steeper than 35º.
4 Installing Mounting Bracket Support Beam “J” Hook (S7) Outlet Box (A) Ceiling OUTLET BOX Mounting Bracket (1) Bracket Screws & Washers (S2) Wood Screws (S1) Wood Screws (S1) NOTE: Do not mount directly to sheet rock or ceiling tile. Prior to securing mounting bracket, screw "J" hook (S7) into ceiling outlet box as a secondary support means. Secure mounting bracket (#1) to the outlet box (A) by tightening bracket screws (S2) as shown.
5 Downrod Assembly Locate downrod assembly (#2). Loosen ball screw on black hanging ball to free lock pin. Black hanging ball will slide down. Remove ground screw and green ground wire. Remove hanging ball from downrod and save all parts. Insert fan wires through downrod.
6 Thread the downrod onto the motor housing making sure the wires don’t get twisted. Insert saftey bolt (S6) through flange & downrod and attach nut. Tighten firmly. Tighten set screw against downrod.
7 Place Flange Cover (6), Anti-Sway Adapter (5) and Canopy (4) over downrod assembly. WARNING: Failure to completely tighten downrod as described in steps above could result in the fan loosening and possibly falling. Replace hanging ball, insert hanging pin through downrod and tighten set screw through hanging ball into downrod. Thread fan wires and safety cable through holes in Waterproof Cover (3) and slide down to cover hanging ball to form water tight seal.
8 Lift fan onto the mounting bracket (#1). Turn housing until hanging ball seats itself into ball socket (listen for click). For added security, thread the safety cable through the nut and make a ring as shown, thread the safety cable into the nut and secure by tightening the screw. Attach safety cable from fan unit to "J" hook (S7) in outlet box. Secure by looping zip tie (S8) through safety cable and "J" hook. Tighten zip tie securely.
9 Ground White (Neutral) Wire Connectors (S6) Black (Power) White Ground (Green) Black Outlet Box Ground (Green) Downrod Ground (Green) Mounting Bracket Ground (Green) 1. Connect fan wires to ceiling wires: white fan wire to white outlet wire, black to black and green to green. Wire connectors (S5) are provided for your convenience. 2. After connections are made, turn splices upward and push carefully into outlet box.
10 Remove two screws from the hanger bracket and reserve. Align the canopy up to ceiling and over the screw holes. Secure the canopy by tightening the removed screws. Step 1. Attach the fan blades to blade arms with screws (S3). Tighten securely. Step 2. Align motor holes to blade assembly and secure with screws (S4) provided. Repeat procedure with remaining blades.
11 Remove one of the three set screws on the mounting ring and loosen the other two screws, do not remove. Snap the light kit connection plugs before installing the light kit. Align the keyholes of the mounting plate with the loosened screws, and tighten the three screws securely. Install 2 JD-Type halogen bulbs (included). Twist the glass shade with glass shade ring to the mounting plate.
Remote Control Operation Instructions ON/OFF For emergency shut off. SPEED CONTROL Controls fan motor speed. To select desired speed, press button once and release. REVERSE Controls direction of fan blades. To reverse fan blades, press once and release. FAN OFF or STOP Turns fan motor speed off. Press once to turn off. To start motor speed again, hit one of the motor speed buttons. L-1 or UPLIGHT Controls the on/off and intensity* for integrated light kit. Push and release for on/off function.
IMPORTANT! PLEASE READ: All Craftmade Ceiling Fans are prepared with a durable lacquer or a painted finish. Your proper care will enhance both the life and appearance. Post treatments, such as clear lacquer, are not recommended. PROPER CARE In order to maximize the appearance of your Craftmade ceiling fan, it is important that dust and debris is removed from the surface periodically.
