Installation Guide

ManualsBrandsCraftmade ManualsPendant LightingToscana Peruvian Bronze Traditional Textured Glass Bell Pendant Light

Craftmade • P.O. Box 1037 • Coppell, TX USA • 75019

4- 2007

IMPORTANT! PLEASE READ:

All Craftmade lighting fixtures are prepared with a durable lacquer finish or a

powder-coated/painted finish. Your proper care of lighting fixtures (see below) will

enhance both the life and appearance of the lighting fixtures. Post treatments, such as clear

lacquer, are not recommended.

PROPER CARE

In order to maximize the appearance of a Craftmade brass lighting fixture, it is important

that dust and debris is removed from the surface of the lighting fixture periodically. It is

recommended that the lighting fixtures be wiped down weekly using a soft, dry or damp

cloth.

DO NOT use any abrasives such as car wax, brass cleaners or other polishes, glass cleaners

or chemicals, as this will scratch/remove/damage the protective coating, allowing

moisture and pollutants to come in contact with the brass, which will result in

discoloration and pitting.

ALL Craftmade cast aluminum lighting fixtures receive a durable powder coat finish,

which enhances the durability of the lighting fixture. This finish should also be wiped

down weekly with a soft, dry or damp cloth to remove the dust and debris that will

accumulate on the surface. DO NOT use any abrasives such as car wax, brass cleaners or

other polishes, glass cleaners or chemicals as this may damage the finish.

FAILURE TO FOLLOW THE ABOVE CARE INSTRUCTIONS WILL VOID THE

WARRANTY OF THE LIGHTING FIXTURE.

For information regarding replacement parts, please write to:

Craftmade, P.O. Box 1037, Coppell, TX 75019

LIMITED WARRANTY

Craftmade warrants against defects in materials or workmanship for a period of ONE (1)

YEAR from date of purchase for use, and agrees to repair or, at our option, replace a

defective unit without charge. Brass finish is covered 90 days from purchase date.

IMPORTANT: This Warranty does not cover damage resulting from accident, misuse or

abuse, lack of reasonable care (see above), the affixing of any attachment not provided with

the product, alteration of any attachments factory installed, loss of parts or subjecting the

fixture to any but the specified electrical service. This warranty does not cover failure of

bulbs due to accidents, abuse, misuse, vandalism, power surges, and acts of nature such as

lightning damage or any bulbs purchased separately and installed by the consumer or any

damage to the fixture caused by a separately purchased bulb.

No responsibility is assumed for any special incidental or consequential damages.

Damages occurring during transit are not covered by this warranty.

To obtain warranty service, mail sales receipt as proof of purchase-date, and a brief

explanation of the nature of the defect, to P.O. Box 1037, Coppell, TX 75019. You will

receive, by mail, a Return Goods Authorization number issued by Craftmade, and returned

freight prepaid.

For Installation or Technical Support, call 1-800-486-4892, 8 a.m. - 5 p.m., Central Time,

Monday-Friday.

Please send the following information…

1. The Model Number and Finish – Polished, Antique, White, etc.

2. The name of the part – if you have a parts problem.

3. Your name, mailing address and phone number

(with area code).

IMPORTANT

Ceiling Mount

Installation Guide

Models:

9124PR3, 9127PR5, 9128PR5, 9138PR8,

9138PR10, 9107PR1, 9112PR1, 9152PR20

and 9144PR3

Disconnect Power

Always shut off power at the circuit breaker or disconnect fuse

when installing or repairing this, or any other electric appliance.

FAILURE TO

DO SO MAY

RESULT IN

SEVERE

INJURY

ORDEATH.

CAUTION

Summary of content (7 pages)

PAGE 1
IMPORTANT IMPORTANT! PLEASE READ: All Craftmade lighting fixtures are prepared with a durable lacquer finish or a powder-coated/painted finish. Your proper care of lighting fixtures (see below) will enhance both the life and appearance of the lighting fixtures. Post treatments, such as clear lacquer, are not recommended. PROPER CARE In order to maximize the appearance of a Craftmade brass lighting fixture, it is important that dust and debris is removed from the surface of the lighting fixture periodically.
PAGE 2
1 2 Prepare Ceiling Outlet NOTE: ALWAYS TURN POWER OFF BEFORE INSTALLING LIGHTING FIXTURES. IMPORTANT: YOU SHOULD USE A QUALIFIED ELECTRICIAN TO INSTALL THIS FIXTURE NOTE: For lighting fixtures over 50 lbs (25 lbs. in Canada) , the mounting bar must be supported independently of the ceiling junction box. Please consult a qualified electrician. a. Prepare outlet box by pulling black, white and ground wires out of electrical outlet box (see figure 1a). b.
PAGE 3
4 Installation and Wiring Installation Installation for the 9138PR8 Chandeliers (see Fig.A) a. Disconnect power at main electrical panel before installation. Supply Wire Supply Ground Wire b. Attach mounting strap to outlet box using box screws provided with outlet box. Fixture Ground Wire c. Screw threaded nipple into collar loop as far as it will go. Secure with lock washer and hexnut. d. Screw threaded nipple into mounting strap approximately 1/2 inch.
PAGE 4
5 6 Prepare 9128PR5 Chandelier a. The chandeliers come folded in the box. Remove the chandelier and unfold it, spacing the arms an equidistance apart. b. Attach the nipple to the coupling and make sure part of nipple is threaded into coupling. c. Slide the glass over the socket until flush with pan. d. Secure glass bowl by screwing socket ring on to socket, tightly. e. Screw the bulb into the socket (Bulb not included). Prepare 9124PR3 Chandelier a. The chandeliers come folded in the box.
PAGE 5
7 Prepare 9152PR20 Chandelier a. The chandeliers come folded in the box. Remove the chandelier and unfold it, spacing the arms with the top font as seen below. b. Attach the nipple to the coupling and make sure part of nipple is threaded into coupling. c. Slide the glass over the socket until flush with pan. d. Secure glass bowl by screwing socket ring on to socket, tightly. e. Screw the bulb into the socket (Bulb not included). 8 Prepare 9138PR10 Chandelier a. The chandeliers come folded in the box.
PAGE 6
9 Prepare 9127PR5 Chandelier a. The chandeliers come folded in the box. Remove the chandelier and unfold it, spacing the arms with the top font as seen below. b. Attach the nipple to the coupling and make sure part of nipple is threaded into coupling. c. Slide the glass over the socket until flush with pan. d. Secure glass bowl by screwing socket ring on to socket, tightly. e. Screw the bulb into the socket (Bulb not included). 10 Prepare 9138PR3 Chandelier a.
PAGE 7
11 Prepare 9144PR3 Chandelier a. Slide the glass over the socket until flush with pan. b. Secure glass bowl by screwing socket ring on to socket, tightly. c. Screw the bulb into the socket (Bulb not included). 12 Prepare 9107PR1 and 9112PR1 a. Slide the glass over the socket until flush with pan. b. Secure glass bowl by screwing socket ring on to socket, tightly. c. Screw the bulb into the socket (Bulb not included).