Installation Guide

Please read carefully and save these instructions, as you may need them at a later date.
Turn off the main power at the circuit breaker before installing the fixture in order to prevent
possible shock.
All electrical connections must be in accordance with local and National Electrical Code (N.E.C.)
standards. If you are unfamiliar with proper electrical wiring connections obtain the services of a
qualified electrician.
Remove all parts and hardware from the box and the mounting package and make sure that none are
missing by referencing the illustrations provided.
1. Pull the SUPPLY WIRES (4 & 6) and the SUPPLY GROUND WIRE (9) out from the OUTLET BOX (1)
(not included) and attach the MOUNTING STRAP (2) assembly to the OUTLET BOX (1) using the slotted
holes of the MOUNTING STRAP (2) and the OUTLET BOX SCREWS and WASHERS (3).
[See Fig. 1]
2. Remove THREADED RING (14) from SCREW COLLAR LOOP (12). Place t
he CANOPY (11) over the
OUTLET BOX (1) and adjust the SCREW COLLAR LOOP (12) and THREADED ROD (15) until
the midpoint of the outside threads on the SCREW COLLAR LOOP (12) is centered (aligned) with
the surface of the CANOPY (11). Remove the CANOPY (11) and tighten both 1/8in. IPS HEX NUTS
(20) down on the MOUNTING STRAP (2) and the SCREW COLLAR LOOP (12). [See Fig. 1]
3. Slide the SMALL RING (23), the SHADE (17), the other SMALL RING (23) and FIXTURE LOOP (16)
down the FIXTURE WIRES (5, 7 and 8) and then thread the FIXTURE LOOP (16) onto the threaded rod at
the top of the FIXTURE (21) until tight. [See Fig. 2]
4. Attach one OPEN CHAIN LINK (18) to each end of the CHAIN (13). Then attach one end of the
CHAIN (13) to the FIXTURE LOOP (16). Slide the THREADED RING (14) and the CANOPY (11)
(in that order) onto the CHAIN (13) and attach the other end of the CHAIN (13) to the SCREW COLLAR
LOOP (12). Close the OPEN CHAIN LINKS (18). [See Fig. 1 & 2]
5. Unravel the FIXTURE LEAD WIRES (5 & 7) and FIXTURE GROUND WIRE (8) and thread them through
every other link of the CHAIN (13) starting with the chain link attached to the FIXTURE LOOP (16).
Feed the FIXTURE LEAD WIRES (5 & 7) and FIXTURE GROUND WIRE (8) through the SCREW
COLLAR LOOP (12) and the THREADED ROD (15). Pull the FIXTURE LEAD WIRES (5 & 7) and the
FIXTURE GROUND WIRE (8) upward to remove any excess slack. [See Fig. 1]
6. Attach the power supply wires to the fixture lead wires by connecting the BLACK SUPPLY WIRE (4) to
the SMOOTH FIXTURE LEAD WIRE (5) and the WHITE SUPPLY WIRE (6) to the RIBBED FIXTURE
LEAD WIRE (7). Loop the SUPPLY GROUND WIRE (9) around the GROUND SCREW (19) on the
MOUNTING STRAP (2). [Note: Be sure to provide an extra 3in. length of the SUPPLY GROUND WIRE (9)
for connection to the FIXTURE GROUND WIRE (8).] Tighten the GROUND SCREW (19). Connect the
remaining SUPPLY GROUND WIRE (9) to the FIXTURE GROUND WIRE (8). Use a WIRE
CONNECTOR (10) for all wire connections. Push wiring and connections inside the OUTLET BOX (1).
[See Fig. 1]
# 28533-GB
GENERAL
ASSEMBLY AND INSTALLATION
CAUTION
FIG. 2
WILLOW PARK
3-LIGHT FOYER
FIG. 1
1. OUTLET BOX (NOT INCLUDED)
2. MOUNTING STRAP
3. OUTLET BOX SCREW and
WASHER (pre-attached to outlet box)
4. BLACK SUPPLY WIRE (not included)
5. SMOOTH FIXTURE LEAD WIRE
6. WHITE SUPPLY WIRE (not included)
7. RIBBED FIXTURE LEAD WIRE
8. FIXTURE GROUND WIRE
9. SUPPLY GROUND WIRE (not included)
10. WIRE CONNECTOR
11. CANOPY
12. SCREW COLLAR LOOP (pre-attached)
Customer Service: 1 [phone]
13. CHAIN
14. THREADED RING
15. THREADED ROD
(pre-attached)
16. FIXTURE LOOP
17. SHADE
18. OPEN CHAIN LINK
19. GROUND SCREW (pre-attached)
20. HEX NUT (pre-attached)
21. FIXTURE
22. THREADED ROD and HEX NUT
8
10
6
4
7
2
19
20
12
3
14
9
5
1
11
18
15
13
20
21
16
17
22
25
24
23
23
23. SMALL RING
24. BOTTOM FONT
25. FINIAL
ASSEMBLY & INSTALLATION (Continued)
7. Slide the CANOPY (11) and the THREADED RING (14) up the CHAIN (13). Place the CANOPY
(11) over the OUTLET BOX (1) and secure it by screwing the THREADED RING (14) onto the
SCREW COLLAR LOOP (12). [See Fig. 1]
8. Install bulbs, MAXIMUM 60W each.
9. Attach THREADED ROD (22) to the bottom of the FIXTURE (21) and secure with the HEX
NUT (22). Secure BOTTOM FONT (24) with the FINIAL (25). [See Fig. 2]
INSTALLATION IS NOW COMPLETE