Installation Guide

Please read carefully and save these instructions, as you may need them at a later date.
Turn off the main power at the circuit breaker before installing the fixture in order to prevent
possible shock.
All electrical connections must be in accordance with local and National Electrical Code (N.E.C.)
standards. If you are unfamiliar with proper electrical wiring connections, obtain the services of a
qualified electrician.
Remove all parts and hardware from the box and the mounting package and make sure that none are
missing by referencing the illustrations provided.
1. Pull the SUPPLY WIRES (4 & 6) and the SUPPLY GROUND WIRE (8) out from the OUTLET BOX (1)
(not included) and attach the MOUNTING STRAP (2) assembly to the OUTLET BOX (1) using the slotted
holes of the MOUNTING STRAP (2) and the OUTLET BOX SCREWS and WASHERS (3). [See Fig. 1]
2. Remove the THREADED RING (14) from the SCREW COLLAR LOOP (12) and set aside. Place the
CANOPY (11) over the OUTLET BOX (1) and adjust the SCREW COLLAR LOOP (12) and THREADED
ROD (15) until the midpoint of the outside threads on the SCREW COLLAR LOOP (12) is centered
(aligned) with the surface of the CANOPY (11). Remove the CANOPY (11) and tighten both
HEX NUTS (20) down on the MOUNTING STRAP (2) and the SCREW COLLAR LOOP (12). [See Fig. 1]
3. While holding the FIXTURE LOOP with THREADED ROD (16), the CAP (27), LARGE RING (28),
SMALL RING (29), and ROD (26), slide the ROD (26) down the FIXTURE WIRES (5, 7, & 9) and place
it over the coupling at the top of the FIXTURE (22). Thread FIXTURE LOOP with THREADED ROD (16)
into the coupling until tight. Pull the arms on the FIXTURE (22) so they are evenly spaced. [See Fig. 2]
4. Attach one OPEN CHAIN LINK (18) to each end of the CHAIN (13). Then attach one end of the
CHAIN (13) to the FIXTURE LOOP (16). Slide the THREADED RING (14) and the CANOPY (11)
(in that order) onto the CHAIN (13) and attach the other end of the CHAIN (13) to the SCREW COLLAR
LOOP (12). Close the OPEN CHAIN LINKS (18). [See Fig. 1 & 2]
5. Unravel the FIXTURE LEAD WIRES (5 & 9) and FIXTURE GROUND WIRE (7) and thread them through
every other link of the CHAIN (13) starting with the chain link attached to the FIXTURE LOOP (16).
Feed the FIXTURE LEAD WIRES (5 & 9) and FIXTURE GROUND WIRE (7) through the SCREW
COLLAR LOOP (12) and the THREADED ROD (15). Pull the FIXTURE LEAD WIRES (5 & 9) and the
FIXTURE GROUND WIRE (7) upward to remove any excess slack. [See Fig. 1]
6. Attach the power supply wires to the fixture lead wires by connecting the BLACK SUPPLY WIRE (4) to the
SMOOTH FIXTURE LEAD WIRE (5) and the WHITE SUPPLY WIRE (6) to the RIBBED FIXTURE
LEAD WIRE (9). Loop the SUPPLY GROUND WIRE (8) around the GROUND SCREW (19) on the
MOUNTING STRAP (2). [Note: Be sure to provide an extra 3in. length of the SUPPLY GROUND
WIRE (8) for connection to the FIXTURE GROUND WIRE (7).] Tighten the GROUND SCREW (19).
Connect the remaining SUPPLY GROUND WIRE (8) to the FIXTURE GROUND WIRE (7). Use a
WIRE CONNECTOR (10) for all wire connections. Push wiring and connections inside the OUTLET
BOX (1). [See Fig. 1]
# 28512-GB
GENERAL
ASSEMBLY AND INSTALLATION
CAUTION
FIG. 1
FIG. 2
12-LIGHT CHANDELIER
1. OUTLET BOX (NOT INCLUDED)
2. MOUNTING STRAP
3. OUTLET BOX SCREW and WASHER
(pre-attached to outlet box)
4. BLACK SUPPLY WIRE (not included)
5. SMOOTH FIXTURE LEAD WIRE
6. WHITE SUPPLY WIRE (not included)
7. FIXTURE GROUND WIRE
8. SUPPLY GROUND WIRE (not included)
9. RIBBED FIXTURE LEAD WIRE
10. WIRE CONNECTOR
11. CANOPY
12. SCREW COLLAR LOOP
ASSEMBLY & INSTALLATION (Continued)
7. Slide the CANOPY (11) and the THREADED RING (14) up the CHAIN (13). Place the CANOPY
(11) over the OUTLET BOX (1) and secure it by screwing the THREADED RING (14) onto the
SCREW COLLAR LOOP (12). [See Fig. 1]
8. Place SHADES (17) over CANDLE COVERS (21) on FIXTURE (22). Install bulbs, MAXIMUM 60W
each. [See Fig. 2]
9. Attach THREADED ROD (23) to the bottom of the FIXTURE (22) and secure with the HEX
NUT (23). Secure BOTTOM FONT (24) with the FINIAL (25). [See Fig. 2]
INSTALLATION IS NOW COMPLETE
WILLOW PARK
Customer Service: 1 [phone]
13. CHAIN
14. THREADED RING
15. THREADED ROD
(pre-attached)
16. FIXTURE LOOP with
THREADED ROD
17. SHADE
18. OPEN CHAIN LINK
19. GROUND SCREW (pre-attached)
20. HEX NUT (pre-attached)
21. CANDLE COVER (pre-attached)
22. FIXTURE
23. THREADED ROD and HEX NUT
24. BOTTOM FONT
25. FINIAL
26. ROD
27. CAP
28. LARGE RING
29. SMALL RING
8
12
10
6
4
7
2
19
20
20
3
18
9
5
1
11
14
15
13
16
28
27
29
26
17
21
22
25
24
23