Installation Guide

ASSEMBLY AND INSTALLATION
1. Take the parts out of the mounting package . Screw the end of the NIPPLE (4) into the center hole of
the MOUNTING BRACKET (2) and thread both 1/8” IPS HEX NUT(5) several turns onto each end of
the NIPPLE(4) but do not tighten the 1/8” IPS HEX NUTS (5). Pull the SUPPLY WIRES (9 & 11) and
the SUPPLY GROUND WIRE (8) out from the OUTLET BOX (1) and attach the MOUNTING
BRACKET (2) assembly to the OUTLET BOX (1) using the slotted holes of the MOUNTING
BRACKET (2) and the MOUNTING SCREWS (3) provided. (See Fig. 1)
2. Thread the SCREW COLLAR LOOP (6) onto the bottom end of the NIPPLE (4). Place the CANOPY
(15) over the OUTLET BOX (1) and adjust the SCREW COLLAR LOOP (6) and NIPPLE (4) until the
midpoint of the outside threads on the SCREW COLLAR LOOP (6) is centered (aligned) with the
surface of the CANOPY (15). Remove the CANOPY (15) and tighten both 1/8” IPS HEX NUTS (5)
down on the MOUNTING BRACKET (2) and the SCREW COLLAR LOOP (6). (See Fig. 1)
3. Thread the CENTER STEM(19) onto the NIPPLE (20) till tight. Thread the FIXTURE LOOP(18) onto
the CENTER STEM(19) till tight.
4. Open up the end links of the CHAIN (17) and attach one end of the CHAIN (17) onto the FIXTURE
LOOP (18). Slide the THREADED RING (16) and the CANOPY (15) onto the CHAIN (17) (in that
order) and attach the other end of the CHAIN (17) to the SCREW COLLAR LOOP (6). Close the ends
of the chain links. (See Fig. 1 and 2)
5. Unravel the fixture lead wires(10 and 12) and FIXTURE GROUND WIRE (7) and thread them
through every other link of the CHAIN (17) starting with the chain link attached to the FIXTURE
LOOP (18). Feed the fixture lead wires(10 and 12) and FIXTURE GROUND WIRE (7) through the
SCREW COLLAR LOOP (6) and NIPPLE (4) assembly. Pull the fixture lead wire(10 and 12) and the
FIXTURE GROUND WIRE (7) upward to remove any excess slack. (See Fig. 1)
6. Attach the power supply wires to the fixture lead wires by connecting the BLACK SUPPLY WIRE (9)
to the SMOOTH FIXTURE LEAD WIRE (10) and the WHITE SUPPLY WIRE (11) to the RIBBED
FIXTURE LEAD WIRE (12). Loop the FIXTURE GROUND WIRE (7) around the GROUND
SCREW (14) of the MOUNTING BRACKET (2). (Note: Be sure to provide an extra 3” length of the
GROUND WIRE(7).) Connect the remaining FIXTURE GROUND WIRE (7) to the SUPPLY
GROUND WIRE (8) using a WIRE CONNECTOR (13). Place wiring and connections inside the
OUTLET BOX (1). (See Fig. 1)
ASSEMBLY AND INSTALLATION (Continued)
6. Slide the CANOPY (15) and the THREADED RING(16) up the CHAIN(17). Place the CANOPY (15)
over the OUTLET BOX (1) and secure it in place by screwing the THREADED RING (16) onto the
SCREW COLLAR LOOP (6).(See Fig.1)
7. Slide the GLASS SHADE(22) over the SOCKET(21), secure with the SOCKET RING(23).
8. Screw light bulb into the lamp socket and make sure it does not exceed the maximum wattage specified on
the fixture’s wattage rating label,
MAXIMUM 100W.
INSTALLATION IS NOW COMPLETED
ASSEMBLY & INSTALLATION
INSTRUCTIONS FOR #24921
Please read carefully and save these instructions, as you may need them at a later date.
GENERAL
All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If
you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician.
Remove the fixture and the mounting package from the box and make sure that no parts are missing by
referencing the illustrations on the installation instructions.
CAUTION
Turn off the main power at the circuit breaker before installing the fixture, in order to prevent possible shock.
1. OUTLET BOX
2. MOUNTING BRACKET
3. MOUNTING SCREW
4. NIPPLE
5. 1/8” IPS HEX NUT
6. SCREW COLLAR LOOP
7. FIXTURE GROUND WIRE
8. SUPPLY GROUND WIRE
9. BLACK SUPPLY WIRE
FIG. 1 FIG. 2
10. SMOOTH FIXTURE LEAD
WIRE
11. WHITE SUPPLY WIRE
12. RIBBED FIXTURE LEAD
WIRE
13. WIRE CONNECTOR
14. GROUND SCREW
15. CANOPY
16. THREADED RING
17. CHAIN
18. FIXTURE LOOP
19. CENTER STEM
20. NIPPLE
21. SOCKET
22. GLASS SHADE
23. SOCKET RING