Network Router User Manual

ManualsBrandsCradlepoint ManualsNetwork RouterMBR95

Summary of content (122 pages)

PAGE 1
PAGE 2
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 Preface CradlePoint reserves the right to revise this publication and to make changes in the content thereof without obligation to notify any person or organization of any revisions or changes. Manual Revisions Revision Date Description Author 1.0 July 19, 2011 Initial release for Firmware version 3.2.4 Jeremy Cramer Trademarks CradlePoint and the CradlePoint logo are registered trademarks of CradlePoint, Inc.
PAGE 3
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 Table of Contents 1 1.1 1.2 1.3 2 PORTS, BUTTONS, AND SWITCHES ............................................ 6 LEDS.................................................................................. 7 BASIC SETUP ...................................................................... 10 CONNECT TO A COMPUTER OR OTHER DEVICE .......................... 11 COMMON PROBLEMS .......................................................... 14 7 ADMINISTRATOR LOGIN ..
PAGE 4
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 9 GLOSSARY..................................................................... 103 10 APPENDIX ................................................................... 117 10.1 10.2 10.3 REGULATORY INFORMATION ............................................. 117 WARRANTY INFORMATION ............................................... 117 SPECIFICATIONS .............................................................. 118 © 2011 CRADLEPOINT, INC.
PAGE 5
CRADLEPOINT MBR1400 | USER MANUAL Firmware ver. 3.2.2 1 INTRODUCTION 1.1 Package Contents     Wireless 4G/3G Router (MBR95) AC power adapter (12V, 1.5A) WARNING: using a power adapter other than the one provided may damage the MBR95 and will void the warranty CAT5 Ethernet Cable (5 feet) Setup Guide 1.2 System Requirements    Ethernet-based, Cable/DSL/Satellite modem; Broadband USB Data Modem with Active Subscription; and/or WiFi as WAN.
PAGE 6
CRADLEPOINT MBR1400 | USER MANUAL Firmware ver. 3.2.2 CradlePoint routers are built to work with most popular 4G/3G USB Modems from: AT&T, Bell Canada, Clearwire, Cricket, Rogers, Sprint, T-Mobile, Telus, US Cellular, Verizon Wireless, & Virgin Mobile, as well as most Cable, DSL, and Satellite providers. ENHANCED WIFI  600+ feet of WiFi Range  Wireless ―N ‖ WiFi (802.11n, legacy 802.
PAGE 7
CRADLEPOINT MBR1400 | USER MANUAL Firmware ver. 3.2.2 2 HARDWARE OVERVIEW © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 8
CRADLEPOINT MBR1400 | USER MANUAL Firmware ver. 3.2.2 2.1 Ports, Buttons, and Switches © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 9
CRADLEPOINT MBR1400 | USER MANUAL Firmware ver. 3.2.2 2.2 LEDs Power: The MBR95 must be powered using an approved 12V DC power source. © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 10
CRADLEPOINT MBR1400 | USER MANUAL Firmware ver. 3.2.2    Green = Powered on. No Light = Not receiving power. Check that the unit is connected to an outlet. Amber = Attention. Check router status page. Active Ethernet Port Connections – 1-4 LAN: Indicates a connected device on the 1-4 LAN ports on the MBR95.    Blue = Connected to an active 10/100 Ethernet interface. Blinking Blue = Traffic.
PAGE 11
CRADLEPOINT MBR1400 | USER MANUAL Firmware ver. 3.2.2 Mobile Broadband Modem (USB) – WAN: Indicates the status of a USB modem connected to the MBR95.        Blue = Modem has established an active 4G connection. Blinking Blue: Modem is connecting to 4G. Green = Modem has established an active 3G connection. Blinking Green = Modem is connecting to 3G. Amber = Modem is not active. Blinking Amber = Data connection error. No modem connection possible. Blinking Red = Modem is in the process of resetting.
PAGE 12
CRADLEPOINT MBR1400 | USER MANUAL Firmware ver. 3.2.2 3 QUICK START 3.1 Basic Setup 1) Connect the Router to a Modem or Data Source: Your router requires an internet source. Insert a supported USB modem; connect a Cable, DSL, or Satellite modem to the Blue Ethernet WAN port; or connect to an available WiFi source. For Failover/Failback functionality, you will need at least two of these sources (for example: an Ethernet source and a USB modem).
PAGE 13
CRADLEPOINT MBR1400 | USER MANUAL Firmware ver. 3.2.2 3.2 Connect to a Computer or other Device 3.2.1 Wireless Network Connection 1) Find the network. On a WiFi-enabled computer or device, open the window or dropdown menu that allows you to access wireless networks. The MBR95 network will appear on the list: select this network. 2) Log in. You will need to input the Default Password when prompted.
PAGE 14
CRADLEPOINT MBR1400 | USER MANUAL Firmware ver. 3.2.2 3.2.2 Accessing the Administration Pages For most users, the MBR95 Router can be used immediately without any special configuration changes.
PAGE 15
CRADLEPOINT MBR1400 | USER MANUAL Firmware ver. 3.2.2 3.2.3 Connect to the Internet If you used the First Time Setup Wizard, you might have changed the ― WiFi Network Name‖ or the ―Se curity Mode‖ password. If so, you will need to reconnect to the MBR95 network.   Find the network. Look for your new personalized network name (or the default SSID of the form ―M BR95xxx‖). Log in using your new personalized WiFi security password (or the Default Password found the bottom of the router).
PAGE 16
CRADLEPOINT MBR1400 | USER MANUAL Firmware ver. 3.2.2 3.3 Common Problems This section contains a list of some of the most common issues faced by users of the MBR95. Please visit CradlePoint Knowledgebase at http://knowledgebase.cradlepoint.com/ for more help and answers to your other questions. 3.3.1 Your USB Modem Does Not Work With the Router  If your USB data modem is not working with the router, check the list of supported devices at http://www.cradlepoint.
PAGE 17
CRADLEPOINT MBR1400 | USER MANUAL Firmware ver. 3.2.2  If the above issues have been resolved and you can connect to the router but you cannot get internet through it using your modem, you may need to upgrade the router firmware. Use your computer (you may need to plug your modem directly into your computer if you don‘t have another way to access the internet) to download the latest firmware for the router (go to http://www.cradlepoint.
PAGE 18
CRADLEPOINT MBR1400 | USER MANUAL Firmware ver. 3.2.2 3.3.2 You are Connected to the Router but Cannot Connect to the Internet The status LEDs of your router will give you an indication whether or not a proper connection is being made. See the LED STATUS definitions below: If the USB data modem LEDs are not illuminated, your modem is not connected and online. You may need to update firmware. Refer to the previous section, ― Your USB Modem Does Not Work With The Router.
PAGE 19
CRADLEPOINT MBR1400 | USER MANUAL Firmware ver. 3.2.2 3.3.3   Your MBR95 router gets an IP conflict when you plug it into your Cable or DSL modem. If your Cable or DSL modem is not working with the router, check that there is not an IP conflict. Go to Internet → Connection Manager and find the Ethernet connection under WAN Interfaces. If it says ―IPconflict‖ you will need to change the IP address of the MBR95 router from ―1 92.168.0.1‖. A suggested IP address is ―19 2.168.10.1‖.
PAGE 20
CRADLEPOINT MBR1400 | USER MANUAL Firmware ver. 3.2.2 4 WEB INTERFACE -- ESSENTIALS The MBR95 has a Web interface for configuration and administration of all features. The interface is organized with a button for toggling between Basic Mode and Advanced Mode and 5 tabs at the top of the screen:      Getting Started Status Network Settings Internet System Settings Click on any of the 5 tabs to open a dropdown menu with further options for the administration of the MBR95. © 2011 CRADLEPOINT, INC.
PAGE 21
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 4.1 Administrator Login To access the administration pages, open a Web browser and type the hostname ― cp/‖ or IP address ― http://192.168.0.1‖ into the address bar. The Administrator Login page will appear. Log in using your administrator password. Initially, this password can be found on the bottom of the MBR95 unit as the Default Password. This password is also the last eight digits of the unit‘s MAC address. © 2011 CRADLEPOINT, INC.
PAGE 22
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 You may have changed the administrator password during initial setup using the First Time Setup Wizard. Log in using your personalized administrator password. If you have forgotten your personalized password, you can reset the MBR95 to factory defaults. When you reset the router, the administrator password will revert back to the Default Password. Press and hold the reset button on the router unit until the lights flash (10 seconds).
PAGE 23
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 4.2 Getting Started – First Time Setup The First Time Setup Wizard will help you customize the name of your wireless network, change passwords to something you choose, and establish an optimal WiFi security mode. The MBR95 comes out of the box with a unique password at WPA1/WPA2 WiFi security level. Note: Instructions for the First Time Setup Wizard are also located in the Setup Guide included with the MBR95.
PAGE 24
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 6) CradlePoint recommends that you customize your WiFi Network Name. Type in your personalized Network name here. You can also enable the Guest Network feature (for more configuration options, see Network Settings → WiFi / Local Network and the Wireless (WiFi) Network Settings section of this manual). Choose the WIFI SECURITY MODE that best fits your needs:     BEST (WPA2): Select this option if your wireless adapters support WPA2-only mode.
PAGE 25
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 Choose a personalized WPA PASSWORD or WEP KEY. This password will be used to connect devices to the router‘s WiFi broadcast once the security settings have been saved. WPA Password: The WPA Password must be between 8 and 64 characters long. A combination of upper and lower case letters along with numbers and special characters is recommended to prevent hackers from gaining access to your network.
PAGE 26
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 7) If you are using a 4G WiMAX modem, you will want to establish the Realm for your carrier. This setting ensures that the modem, when attached to the router, will properly connect to your carrier‘s wireless broadband service. The MBR95 will default to the Sprint Realm. Select your carrier from the dropdown menu (options shown below).        Clear - clearwire-wmx.net Rover - rover-wmx.net Sprint 3G/4G - sprintpcs.com Xohm - xohm.
PAGE 27
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 8) Review the details and record your wireless network name, administrative password, and WPA password (or WEP key). Move your mouse over the passwords to selectively reveal each password. Please record these settings for future access. You may need this information to configure other wireless devices. NOTE: If you are currently using the MBR95 WiFi network, reconnect your devices to the network using the new wireless network name and security password.
PAGE 28
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 4.3 Quick Links The CradlePoint logo in the upper left-hand corner of all the administration pages is a link to the Router Console (Status → Router Console), which displays fundamental information about the router. The black bar across the top provides quick access to important information and controls. Internet Connection This links to the Connection Manager (Internet → Connection Manager) where you can manage your internet sources.
PAGE 29
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 4.4 Basic Mode vs. Advanced Mode For less complex uses, the MBR95 can be controlled within Basic Mode. Clicking on the Basic Mode button switches the complete Web interface to Advanced Mode. Advanced Mode provides several additional features.
PAGE 30
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 4.5 Network Settings vs. Internet When using the Web interface, it will be important to pay attention to the difference between the internet source for your MBR95 and the network created by the MBR95. The “Internet” tab broadly refers to the router‘s source of internet, while the “Network Settings” tab broadly refers to the network created by the router.
PAGE 31
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 5 STATUS The Status tab displays information—no adjustments can be made from within this tab. It provides access to 7 submenu options:       Client List GPS Router Console Internet Connections Statistics System Logs © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 32
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 5.1 Client List The Client List displays the specifications of each device connected to your router, including Wireless and Wired clients. Wireless Clients. For each device using a wireless connection to your MBR95, the following information is displayed: Hostname, IP, MAC, Connection, and Time Online. Wired Clients. For each device using a wired connection to your MBR95, the following information is displayed: Hostname, IP, and MAC.
PAGE 33
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 poor. Signal quality can be reduced by distance, by interference from other radio-frequency sources (such as cordless telephones or neighboring wireless networks), and by obstacles between the router and the wireless device. Time Online: Simply the amount of time the device has been connected to the router. © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 34
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 5.2 GPS If GPS support is enabled and a modem capable of providing GPS coordinates is connected, this page will show a graphical view of your router's location. See the GPS section in System Settings → Administration to enable GPS support. GPS information is only displayed if 1) the modem supports GPS, 2) your carrier allows the GPS functionality, and 3) the modem has sufficient GPS signal strength.
PAGE 35
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 5.3 Router Console The Router Console functions as a dashboard for the router, bringing various types of fundamental information together in one place. Once you have completed initial setup, every time you log in you will automatically be directed to this Router Console page. Also, clicking on the CradlePoint logo in the upper left-hand corner will redirect you to the Router Console page.
PAGE 36
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 Router Information    Product: MBR95 Date: Year-month-day-hours-minutes-seconds for the most recent firmware upgrade. Firmware: Gives the number of the current firmware version. To check for Firmware upgrades, see System Settings → System Software. Internet      State: Connected/Disconnected, active WAN type (Ethernet, Modem, etc.), signal strength. IP Address Netmask Gateway DNS Servers To configure ―S tate‖ see Internet → Connection Manager.
PAGE 37
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 WiFi Network       WiFi Radio: Enabled/Disabled Channel: 1-11 Network Name Clients: Number of clients. Security: WPA2/WPA1/WEP Guest WiFi: Disabled/Enabled. If Enabled, also shows: o Guest Network Name o Guest Security To configure WiFi network settings see Network Settings → WiFi / Local Network. System     Up Time: Total time for current session. Load Average CPU Usage Time: Current local time. © 2011 CRADLEPOINT, INC.
PAGE 38
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 5.4 Internet Connections The Internet Connections submenu option provides a list of attached WAN devices used as the internet source for the MBR95. Select one of these devices to see detailed information about that particular device. For each type of device, different information will be included in the Device Information section.
PAGE 39
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 5.4.1 Ethernet Diagnostics  Connection State (connected, idle, etc.) General Information      Protocol Ethernet Static Product Built-in Ethernet Type Ethernet Port Unique Identifier Statistics     Outgoing Bits/Second Incoming Bits/Second Incoming Bytes Outgoing Bytes © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 40
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 5.4.2 WiFi as WAN Diagnostics  Connection State (connected, idle, etc.) General Information    Product Wireless As WAN Unique Identifier Type wwan IP Information    Netmask IP Address Gateway © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 41
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 5.4.3 GSM Modem (Nokia Datacard) Diagnostics         Signal Error Rate Modem Firmware Version Battery Status Battery Level Carrier Status Signal Strength(dBm) PIN Status Connection State (connected, idle, etc.
PAGE 42
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4    Incoming Bits/Second Incoming Bytes Outgoing Bytes © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 43
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 5.4.4 EVDO Modem: (MC760 Comcast) Diagnostics        Modem Firmware Version PRL Version Service Display EVDO Carrier Status Signal Strength(dBm) Connection Type CDMA Connection State (connected, idle, etc.) General Information         Product MC760 COMCAST Protocol PPP Unique Identifier ESN/IMEI Model MC760 COMCAST Type modem Port Manufacturer Novatel Wireless Inc.
PAGE 44
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4  Outgoing Bytes © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 45
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 5.4.5 WiMAX Modem (U300 – 4G) Diagnostics For a WiMAX modem, the CINR and Signal Strength values are important as they show how strong the signal is and that has significant effects on how much data the router can download or send. You can place the router in different locations to see where you get better signal. You can also see a LED display of the current signal strength. Pressing the router's WPS button will toggle the LED display on and off.
PAGE 46
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4    Type WiMAX Port Manufacturer Franklin Wireless Corporation Statistics     Outgoing Bits/Second Incoming Bits/Second Incoming Bytes Outgoing Bytes © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 47
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 5.4.6 LTE Modem (PANTECH UML290) Diagnostics                   Home Address MN-HA SPI Modem Firmware Version Battery Status MN-HA SS Network Address Identifier (NAI) Signal Strength(dBm) Rev Tun Battery Level Secondary Home Agent Service Display LTE Primary Home Agent Carrier Status Profile MN-AAA SPI PIN Status MN-AAA SS Connection State (connected, idle, etc.) © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 48
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 General Information         Product PANTECH UML290 Protocol IP DHCP Unique Identifier ESN/IMEI Model UML290VW Type modem Port Manufacturer Pantech, Incorporated IP Information    Netmask IP Address Gateway Statistics     Outgoing Bits/Second Incoming Bits/Second Incoming Bytes Outgoing Bytes © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 49
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 5.5 Statistics The Statistics submenu option displays basic traffic statistics for both LAN and WAN connections, separating Outgoing Traffic and Incoming Traffic. Data Rate: A measure of the amount of information that is currently being sent or received through the network. Data: A measure of the total amount of information that has been sent or received. Packets: The number of network packets that have been sent or received.
PAGE 50
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 5.6 System Logs The router automatically logs (records) events of possible interest in its internal memory. If there is not enough internal memory for all events, logs of older events are deleted, but logs of the latest events are retained. The log options allow you to filter the router logs you want to view. You can define what types of events you want to view and the level of events to view.
PAGE 51
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 52
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 6 NETWORK SETTINGS The Network Settings tab provides access to 8 submenu options for administering the following functions/tasks. These functions are all related to controlling the LAN (Local Area Network), the network you set up with the MBR95.         Content Filtering DHCP Server DNS Firewall MAC Filter Routing WiFi / Local Network WiPipe QoS (DHCP Server, DNS, Firewall, Routing, and WiPipe QoS: Advanced Mode only) © 2011 CRADLEPOINT, INC.
PAGE 53
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 6.1 Content Filtering You have two main options for filtering content in the network created through your MBR95. 1) Domain / URL Filter Rules: Create a list of disallowed websites (facebook.com, for example). 2) OpenDNS Content Filtering: Allows several options for filtering rules. 6.1.1 OpenDNS OpenDNS is a service that protects you online by filtering websites. OpenDNS protects you from phishing websites and URL typos once you select a filtering level.
PAGE 54
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 In addition to the standard filtering levels, you have the following options for filter control: Custom OpenDNS: To use the Custom OpenDNS setting you need to first create an OpenDNS account. You can create an account at OpenDNS and click on the ― Create Account‖ link. Follow the onscreen instructions to create an account. Once you have an OpenDNS account, enter your account information in order to use your Custom OpenDNS settings.
PAGE 55
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 6.2 DHCP Server (Advanced Mode only) DHCP stands for Dynamic Host Configuration Protocol. The built-in DHCP Server automatically assigns IP addresses to the computers and other devices on your local area network (LAN) and Wireless local area network (WLAN). In this section, you have options for configuring the DHCP Server and controlling some of its features.
PAGE 56
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 Active Leases: A list of devices that have been provided DHCP leases. The DHCP Server automatically assigns these leases. This list will not include any devices that have static IP addresses on the network. Reservations: This option lets you reserve IP addresses and assign the same IP address to the network device with the specified MAC address any time it requests an IP address.
PAGE 57
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 6.3 DNS (Advanced Mode only) DNS, or Domain Name System, is a naming system that translates between domain names (www.cradlepoint.com, for example) and internet IP addresses (206.207.82.197). A DNS server acts as an internet phone book, translating between names that make sense to people and the more complex numerical identifiers.
PAGE 58
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 6.3.2 DynDNS Configuration The Dynamic DNS feature allows you to host a server (Web, FTP, Game Server, etc.) using a domain name that you have purchased (www.yourname.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses. When you use a Dynamic DNS service provider, you can enter your host name to connect to your server, no matter what your IP address is.
PAGE 59
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 Password: Enter the password or key provided by the Dynamic DNS service provider. 6.3.3 Advanced DynDNS Settings Update period (hours). (Default: 576) The time between periodic updates to the Dynamic DNS, if your dynamic IP address has not changed. The timeout period is entered in hours so valid values are from 1 to 8760. Override External IP. The external IP is usually configured automatically during connection.
PAGE 60
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 ―R eservations‖ section under Network Settings → DHCP Server and reserve the IP address for the device. © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 61
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 6.4 Firewall (Advanced Mode only) The router automatically provides a firewall. Unless you configure the router to the contrary, the router does not respond to unsolicited incoming requests on any port, thereby making your LAN invisible to cyber attackers. However, some network applications, such as some internet gaming systems, cannot run with a tight firewall. Those applications need to selectively open ports in the firewall to function correctly.
PAGE 62
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 Add New Port Forwarding Rule: page 2     Use Port Range: Changes the selection options to allow you to input a range of ports (if desired). Internet Port(s): The port number(s) as you want it defined on the internet. Typically these will be the same as the local port numbers, but they do not have to be. These numbers will be mapped to the local port numbers.
PAGE 63
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 6.4.2 IP Filter Rules An "Incoming" IP filter rule restricts remote access to computers on your local network. "Outgoing" filter rules prevent computers on your local network from initiating communication to the address range specified in the rule. This feature is especially useful when combined with port forwarding and/or DMZ to restrict remote access to a specified host or network range.
PAGE 64
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4     Start Port: 80 End Port: 80 Network Address: 172.22.24.160 (Johnny‘s IP address) Subnet Mask: 255.255.255.255 (This subnet mask restricts the rule to one single address). © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 65
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 6.4.3 DMZ (DeMilitarized Zone) A DMZ host is effectively not firewalled in the sense that any computer on the internet may attempt to remotely access network services at the DMZ IP address. Typical uses involve running a public Web server, supporting older games, or sharing files. Input the IP Address of a single device in your network to create a DeMilitarized Zone for that device.
PAGE 66
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 6.5 MAC Filter The MAC Filter allows you to create a list of devices that have either exclusive access (white list) or no access (black list) to your wireless LAN. By default, the list of addresses is designated a ―w hite list.‖ Deselecting White List turns the list of addresses into a disallowed black list. Advanced: Add devices to either your white list or black list simply by inputting each device‘s MAC address. © 2011 CRADLEPOINT, INC.
PAGE 67
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 6.6 Routing (Advanced Mode only) Add a new static route to the IP routing table or edit/remove an existing route. Static routes are unnecessary for most users. They are typically only used in networks with more than one layer, such as when there is a network within a network so that packet destinations are hidden behind an additional router.
PAGE 68
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 6.7 WiFi / Local Network This section is used to configure the settings for wireless networks created by your router. Note that changes made in this section may also need to be duplicated on wireless devices that you want to connect to your wireless network. For example, if you change the LAN IP address, devices within your network will lose connection to the LAN. They will have to reconnect to your network. 6.7.
PAGE 69
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 6.7.2 Wireless (WiFi) Network Settings By default, the MBR95 has two wireless networks set up: Primary and Guest. ― Primary‖ is the main network for this router. ―Gue st‖ is an additional network that you may enable (this is disabled by default) to allow other people to briefly use your internet connection without knowing your Primary security password. It may have different security modes than your Primary network.
PAGE 70
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 Security Mode: You have several options for selecting a security mode. The mode you choose depends on the security features your wireless adapters support. If you select one of the security modes and are unable to connect to the router afterwards, you can use the reset buttons to reset the router to its factory default state and try a different security mode instead.
PAGE 71
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 6.7.3 WiFi Settings Random Channel: Select to randomize the WiFi channel. This makes it less likely that the wireless signal from this router will conflict with another router in the same area. Channel: The WiFi channel corresponds to a frequency the router uses to communicate with other devices. The range is 1 to 11, and 1, 6, and 11 do not overlap each other.
PAGE 72
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 Optimize WiFi/WiMAX coexistence: Setting this will lessen any possible conflict with WiFi in the 2.4 GHz band and an attached WiMAX modem. If a WiMAX modem is attached to the router when the WiFi is enabled, the WiFi channel and transmit power will be set to levels that optimize the performance of the WiMAX modem. If no WiMAX modem is attached, then default channel and power settings will be used even if this is selected.
PAGE 73
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 WPS: WiFi Protected Setup is a method for easy and secure establishment of a wireless network. It can be used instead of passwords when connecting clients that support WPS. Short Slot: Slot Time is the period wireless clients use in determining if the channel is free for transmission. Enabling this value allows clients that can utilize a shorter time to do so.
PAGE 74
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 Greenfield Mode: Greenfield mode uses an 802.11n-only preamble to transmit packets that older wireless clients cannot interpret. Use of greenfield mode in a mixed 802.11 environment may result in degraded performance but can improve performance if all devices in the area are 802.11n compatible. Antenna Diversity Mode: Antenna Diversity selects the optimal antenna to use for wireless reception.
PAGE 75
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 6.8 WiPipe QoS (Advanced Mode only) When WiPipe QoS (Quality of Service/Traffic Shaping) is enabled, the router will control the flow of internet traffic according to the userdefined rules. In other words, Traffic Shaping improves performance by allowing the user to prioritize applications. Enable WiPipe QoS: Click on this box to open options for controlling internet traffic. You can control Uplink Speed values or define your own Traffic Shaping rules.
PAGE 76
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 automatic classification will be adequate, and specific Traffic Shaping Rules will not be required. Traffic Shaping supports overlap between rules, where more than one rule can match for a specific message flow. If more than one rule matches, the rule with the highest priority will be used. Name. Create a name for the rule that is meaningful to you. Protocol. The protocol used by the messages: TCP, UDP, or ICMP.
PAGE 77
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 The second page allows you to designate the computer(s) on the local network for which you want to adjust traffic priority. NOTE: Leaving a field empty will match any IP address and/or any port number. All fields are optional. Local Start Port and Local End Port: The rule applies to a flow of messages whose LAN-side port number is within the range set here. Local IP Address: The rule applies to a flow of messages with this LAN-side IP address.
PAGE 78
CRADLEPOINT MBR95| USER MANUAL Firmware ver. 3.2.4 The third and last page allows you to designate the network or server on the internet for which you want to shape traffic. NOTE: Leaving a field empty will match any IP address and/or any port number. All fields are optional. Remote Start Port and Remote End Port: The rule applies to a flow of messages whose WAN-side port number is within the range set here. Remote IP Address. The rule applies to a flow of messages with this WAN-side IP address.
PAGE 79
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 7 INTERNET The Internet tab provides access to 7 submenu items for managing a variety of internet connection options.     Connection Manager Ethernet Settings Modem Settings WiFi as WAN Settings (WiFi as WAN Settings: Advanced Mode only) © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 80
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 7.1 Connection Manager The router can establish an uplink via the Ethernet WAN port, WiFi as WAN, or modems plugged into a modem port. If the primary WAN connection fails the router will automatically attempt to bring up a new link on another device. This feature is called failover. If Load Balance is enabled, multiple WAN devices may be plugged in and each may establish a link. 7.1.
PAGE 81
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 7.1.2 Failure Check (Advanced Mode Only) If this is enabled, the router will check that the highest priority active WAN interface can get to the internet even if the WAN connection is not actively being used. If the interface goes down, the router will switch to the next highest priority interface available.
PAGE 82
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 7.1.3 Failback Configuration (Advanced Mode Only) This is used to configure failback, which is the ability to go back to a higher priority WAN interface if it regains connection to its network. Usage: Failback based on the amount of data passed over time. Use of the active connection must be below this threshold for failback to occur. This will limit the interruption that occurs during failback.     High (Rate: 80 KB/s. Time Period: 30 seconds.
PAGE 83
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 7.2 Ethernet Manager The Ethernet Manager provides controls for your router‘s Ethernet ports. There are five total ports: one blue WAN port and four numbered yellow LAN ports. While default settings will be sufficient in most circumstances, you have the ability to control: Link Speed, MAC addresses, and Connect Method for the WAN port and Link Speed for the LAN ports. 7.2.1 Mode WAN or LAN.
PAGE 84
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 7.2.3 MAC Only applicable in WAN mode. You have the ability to change this MAC address, but typically this is unnecessary. 7.2.4 Connect Method Only applicable in WAN mode. Your router‘s Ethernet ports are automatically configured for DHCP connection. If you want to use a Static (Manual) or PPPoE connection instead, you will need to fill out additional information.
PAGE 85
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 7.3 Modem Settings This section shows all attached modems and allows you to change settings. If you have a 3G/4G dual-mode modem it will show both modems using the same USB port. 7.3.1 Update/Activate a Modem Some 3G modems can be updated and activated while plugged into the router. Updates and activation methods vary by modem model and service provider. Possible methods are: PRL Update, Activation, and FUMO.
PAGE 86
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 The modem supports Update/Activate methods: A message will display showing options for each supported method:    Modem Activation / Update: Activate, Reactivate, or Upgrade Configuration. Preferred Roaming List (PRL) Update Firmware Update Management Object (FUMO) Click the appropriate icon to start the process. If the modem is connected when you start an operation the router will automatically disconnect it.
PAGE 87
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 7.3.2 Modem Connection Settings (Advanced Mode Only) This section changes settings that affect how all modems attempt to connect to the service provider's network. Connection Mode: Typically modem connections are not set to remain on. The router allows you to set the type of reconnection mode.  Always On: A connection to the internet is continuously maintained.  On Demand: A connection to the internet is made as needed.
PAGE 88
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 Configuration Rule: First page. Create a name for your rule and the condition for which the rule applies. Rule Name: Create a name meaningful to you. Select each of the following to create a condition for your rule.
PAGE 89
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4        Clear – clearwire-wmx.net Rover – rover-wmx.net Sprint 3G/4G – sprintpcs.com Xohm –xohm.com BridgeMAXX – bridgeMAXX.com Time Warner Cable – mobile.rr.com Comcast – mob.comcast.net TTLS Authentication Mode: TTLS inner authentication protocol.  MSCHAPv2/MD5  PAP  CHAP TTLS Username: Username for TTLS authentication. TTLS Password WiMAX Authentication Identity: User ID on the network.
PAGE 90
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 Configuration Rule: Modem Settings AT Dial Script: Enter the AT commands to be used in establishing a network connection. Each command must be entered on a separate line. All command responses must include ― OK‖ except the final command response, which must include ―CON NECT‖. Example: AT AT+CGDCONT=2,‖IP‖,‖isp.
PAGE 91
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4   Force EVDO: Connect to CDMA EVDO network only. Force 1xRTT: Connect to CDMA 1xRTT network only. © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 92
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 7.4 WiFi as WAN Settings (Advanced Mode only) When WiFi as WAN is enabled and configured the router will use a remote WiFi access point for internet connectivity. In other words, external WiFi—from a hotel for example—can be used as the internet source for your own private network. When enabled in the WiFi as WAN Settings page, the MBR95 will find possible WiFi sources that you can select and add.
PAGE 93
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 want to connect is invisible. Network Name (SSID): The name that is broadcast from each access point. Network ID (BSSID): The numeric ID of the network. This parameter is required when trying to connect to a hidden network using WiFi as WAN. It is optional when connecting to a visible network. Auth Mode: The type of encryption that is used by the network.
PAGE 94
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 7.4.3 Scanning Settings (Advanced Mode Only) Scan Interval: How often WiFi as WAN scans the environment for updates. Scan While Connected: Continue to scan for WiFi as WAN profile updates when connected. Each time a scan occurs the wireless communication of the router will be temporarily interrupted. Normally this should be disabled. © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 95
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 8 SYSTEM SETTINGS The System Settings tab has 6 submenu items that provide access to tools for broad administrative control of the MBR95:      Administration Alerts Managed Services System Control System Software (Alerts and Managed Services: Advanced Mode only) © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 96
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 8.1 Administration Select the Administration submenu item in order to control any of the following functions:       8.1.1 Web Login Network Time Protocol Timezone Bounce Pages UPnP Remote Management Web Login This password is the administration password; this is separate from the WiFi security password. It allows a user to change router settings. This password can also be changed through the First Time Setup Wizard.
PAGE 97
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 This is the time zone and daylight savings setting used by the router for its own clock. This can also be controlled in the First Time Setup Wizard. Daylight Savings Time: Select this checkbox if your location observes daylight savings time. 8.1.4 Bounce Pages Bounce pages show up in your web browser when the router is not connected to the internet. They inform you that you are not connected and try to explain why.
PAGE 98
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 WAN Hostname: This hostname is the DNS name associated with the router's internet connection interface. If DHCP is used on the interface this hostname will be used when requesting a DHCP lease. Allow Remote Administration: When remote administration is enabled it allows access to these administration web pages from the internet. With it disabled, you must be a client on the local network to access the administration website.
PAGE 99
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 o Report only over specific time interval: Restricts the NMEA sentence reporting to a remote server to a specific time interval. 8.1.8 Syslog Settings Enabling this option will send log messages to a specified Syslog server. After enabling, type the Hostname or IP address of the Syslog server. © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 100
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 8.2 Alerts (Advanced Mode only) The Alerts submenu choice allows you to receive email notifications of specific system events. You will need to enable an SMTP email server to send alerts. Alerts can be included for the following:    Firmware Upgrade Available: A firmware update is available for this device. Full System Log: The system log has filled. This alert contains the contents of the system log.
PAGE 101
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 Server Address: smtp.gmail.com Server Port: 587 (for TLS, or Transport Layer Security port; the MBR95 does not support SSL). Authentication Required: For Gmail, mark this checkbox. User Name: Your full email address Password: Your Gmail password From Address: Your email address To Address: Your email address Once you have filled in the information for the SMTP server, click on the ―V erify SMTP Settings‖ button.
PAGE 102
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 8.3 Managed Services (Advanced Mode only) ASK YOUR CRADLEPOINT SALES REPRESENTATIVE FOR DETAILS Managed Services allow you to centralize your router configuration using the WiPipe Central server. WiPipe Central services must be purchased separately. Enable Services: Enables the WiPipe Central client to contact the server. Ethernet Communication Only: The WiPipe Central client will not start unless the WAN is Ethernet.
PAGE 103
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 8.4 System Control Restore to Factory Defaults: This changes all settings back to their default values. Reboot The Device: This causes the router to restart. Advanced: Scheduled Reboot and Ping Test Scheduled Reboot: This causes the router to restart at a user-determined time. Ping Test: A simple test to check internet connectivity. Type the Hostname or IP address of the computer you want to ping and press 'Enter' or click the 'Ping' button.
PAGE 104
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 8.5 System Software Firmware Upgrade: This allows the administrator to load new firmware onto the router to add new features or fix defects. If you are happy with the operation of the router, you may not want to upgrade just because a new version is available. Check the firmware release notes for information to decide if you should upgrade or not. Automatic (Internet): Have the router download the file and perform the upgrade with no user interaction.
PAGE 105
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 9 GLOSSARY 802.11 Alphanumeric A family of specifications for wireless local area networks (WLANs) developed by a working group of the Institute of Electrical and Electronics Engineers (IEEE). Characters A-Z and 0-9. Access Control List ACL. This is a database of network devices that are allowed to access resources on the network. Access Point AP. Device that allows wireless clients to connect to it and access the network.
PAGE 106
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 Authentication Bit rate To provide credentials, like a Password, in order to verify that the person or device is really who they are claiming to be. The amount of bits that pass in given amount of time. Automatic Private IP Addressing APIPA. An IP address that a Windows computer will assign itself when it is configured to obtain an IP address automatically but no DHCP server is available on the network.
PAGE 107
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 CardBus Data-Link layer A newer version of the PC Card or PCMCIA interface. It supports a 32- bit data path, DMA, and consumes less voltage. The second layer of the OSI model. Controls the movement of data on the physical link of a network. CAT 5 Category 5. Used for 10/100 Mbps or 1Gbps Ethernet connections. Organizes information so that it can be managed updated, as well as easily accessed by users or applications.
PAGE 108
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 Demilitarized zone Download DMZ: A single computer or group of computers that can be accessed by both users on the internet as well as users on the Local Network, but that is not protected by the same security as the Local Network. To send a request from one computer to another and have the file transmitted back to the requesting computer.
PAGE 109
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 Encryption Fragmentation Converting data into cyphertext so that it cannot be easily read. Breaking up data into smaller pieces to make it easier to store. Ethernet FTP The most widely used technology for Local Area Networks. File Transfer Protocol. Easiest way to transfer files between computers on the internet. Fiber optic Full-duplex A way of sending data through light impulses over glass or plastic wire or fiber.
PAGE 110
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 Half-duplex IEEE Data cannot be transmitted and received at the same time. Institute of Electrical and Electronics Engineers. Hashing Transforming a string of characters into a shorter string with a predefined length. Internet Group Management Protocol is used to make sure that computers can report their multicast group membership to adjacent routers. Hexadecimal IIS Characters 0-9 and A-F.
PAGE 111
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 Internet Protocol Security Java IPsec provides security at the packet processing layer of network communication. A programming language used to create programs and applets for web pages. Internet Service Provider Kbps An ISP provides access to the internet to individuals or companies. Kilobits per second. Intranet Kilobyte. A private network.
PAGE 112
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 LPR/LPD MPPE ―Line Printer Requestor‖/‖Line Printer Daemon‖. A TCP/IP protocol for transmitting streams of printer data. Microsoft Point-to-Point Encryption is used to secure data transmissions over PPTP connections. MAC Address MTU A unique hardware ID assigned to every Ethernet adapter by the manufacturer. Maximum Transmission Unit is the largest packet that can be transmitted on a packet-based network like the internet.
PAGE 113
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 Network Interface Card NIC. A card installed in a computer or built onto the motherboard that allows the computer to connect to a network. Network Layer The third layer of the OSI model which handles the routing of traffic on a network. Network Time Protocol Used to synchronize the time of all the computers in a network. NIC Password A sequence of characters that is used to authenticate requests to resources on a network.
PAGE 114
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 channel) but can have multiple ports (logical channels) each identified by a number. PPP Point-to-Point Protocol is used for two computers to communicate with each over a serial interface, like a phone line. PPPoE Point-to-Point Protocol over Ethernet is used to connect multiple computers to a remote server over Ethernet. PPTP Point-to-Point Tunneling Protocol is used for creating VPN tunnels over the internet between two networks.
PAGE 115
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 Session key SSH An encryption and decryption key that is generated for every communication session between two computers. Secure Shell is a command line interface that allows for secure connections to remote computers. Session layer SSID The fifth layer of the OSI model which coordinates the connection and communication between applications on both ends. Service Set Identifier is a name for a wireless network.
PAGE 116
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 TFTP Upload Trivial File Transfer Protocol is a utility used for transferring files that is simpler to use than FTP but with less features. To send a request from one computer to another and have a file transmitted from the requesting computer to the other. Throughput UPnP The amount of data that can be transferred in a given time period. Universal Plug and Play.
PAGE 117
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 Wake on LAN WiFi Protected Access Allows you to power up a computer through its Network Interface Card. An updated version of security for wireless networks that provides authentication as well as encryption. WAN Wide Area Network Wide Area Network. The larger network that your LAN is connected to, which may be the internet itself, or a regional or corporate network. WCN Windows Connect Now.
PAGE 118
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 Yagi antenna A directional antenna used to concentrate wireless signals on a specific location. © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.
PAGE 119
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 10 APPENDIX 10.1 Regulatory Information of the following measures:     This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 120
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 3G/4G Modem Status, WPS (WiFi Protected Setup), Signal Strength 10.3 Specifications MODEL NAME MBR95 Wireless 4G/3G Router WAN / INTERNET 3G/4G via USB modem; one default Ethernet port (10/100) LAN WiFi 802.11 b/g/n, four default Ethernet ports (10/100); one additional WAN Ethernet port re-configurable to LAN use DIMENSIONS 7.9-in x 5.3-in x 1.5-in (199.7mm x 134.7mm x 38.7mm), 0.5 lbs.
PAGE 121
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.
PAGE 122
CRADLEPOINT MBR95 | USER MANUAL Firmware ver. 3.2.4 http://www.cradlepoint.com/ Copyright © 2011 by CradlePoint, Inc. All rights reserved. © 2011 CRADLEPOINT, INC. PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.