DSPMOD-CP-S/CDMA & DSPMOD-CP/CDMA External CDMA Modem Kit
This page intentionally left blank.
Table of Contents Product Registration Information ...................................................................................... 4 DISCLAIMER ........................................................................................................................ 4 Document Purpose / Intended Users................................................................................. 4 Application .............................................................................................................
Product Registration Information If applicable the ESN number may be found on the label on the bottom of the router. Note ESN number below. If not yet activated, the ESN number will be required to do so. Retain this manual, along with proof of purchase, to serve as a permanent record of your purchase. MODEL NUMBER ESN NUMBER DATE OF PURCHASE POINT OF SALE COMPANY DISCLAIMER All information and statements contained herein are accurate to the best of the knowledge of Cellular Specialties, Inc.
CSI CDMA External Modem Kit for Use With Digital Repeater Installations Warning: CSI digital repeaters, with software version 2.3.1 or higher are designed to support the integration of the CSI CDMA External Modem Kits. Check your repeater’s Status Page for software version and contact CSI if you need an update. See Repeater Login Section for information on how to get to the System Status Page to verify your software version.
CradlePoint IBR650E Hardware Overview Ports, LED’s and Switches Power 12VDC: The power connector includes two pins for power and two pins for GPIO (General Purpose Input/Output) functionality. The included power adapter, however, only connects to the power pins. You will need a separate adapter for GPIO functionality. Reset: You can return your router to factory default settings by pressing and holding the Reset button.
Power On/Off: - I = On - O = Off Power LED: - Blue = On - No light = Off ATTN LED: - Used with Modem LED for additional LED indications below.
Mounting Bracket -8-
Attaching the IBR650 to the Mounting Bracket 1) Attach the bracket to the wall or other surface with screws. NOTE: Screws are not provided because the type of screw required depends on the mounting surface 2) Place the router‘s edge against the bottom of the bracket. 3) Press the router down firmly, then push it inside the bracket. It should latch.
Removing the IBR650 from the Mounting Bracket From the top of the bracket, press down firmly on the router using your thumb(s) and pull the device out. Basic Setup 1. Attach one modem antenna to the RX Diversity Port.
2. Plug the power supply into an electrical outlet and connect it to the IBR650. 3. Make sure the power is switched on.
Modem Activation NOTE: CradlePoint IBR650E modems purchased from CSI will be pre-configured; however, if your modem has lost its configuration, you can load a configuration file or manually set up your modem. The default configuration file is included on the CD that shipped with your modem kit. Alternatively, you can request a configuration file from productsupport@cellularspecialties.
Step 2: Activating the CradlePoint IBR650E on the Verizon Wireless Network: Click on the Internet tab, then select Connection Manager Next, highlight “Modem: Internal EVDO and then click on Control -13-
Click on the Activate button The modem will now contact the Verizon Wireless Network for authentication. If the ESN has been set up with an active account, the modem will respond activated within 3-5 minutes. Once you see the above message, reset or power cycle the modem using the on/off switch.
Step 3: Configuring your modem for port forwarding, to support one or multiple devices: CradlePoint IBR650E modems purchased from CSI will be pre-configured; however, if your modem has lost its configuration, you can load a configuration file or manually set up your modem. The default configuration file is included on the CD that shipped with your modem kit. Alternatively, you can request a configuration file from productsupport@cellularspecialties.com.
LAN Settings Under Network Settings, select Local Networks. On both Primary & Guest LAN, DHCP Server should be disabled to prevent misuse of the modem. You may change the Guest LAN IP Address at this point. The Guest LAN IP can be used to monitor other DAS equipment on a different network/subnet. You will also need to change the IP address of the computer that you are using if you wish to access the modem on the Guest LAN (see section under “LAN Settings” for more information).
Additional Features System Automatic Reboot – The CradlePoint IBR650E allows you to set an automatic reboot daily, weekly or monthly. Go to System Settings, System Control to utilize this feature.
Dual LAN The CradlePoint IBR650E allows the use of 2 distinct LAN’s, which is useful when connecting equipment that already has an established subnet (a fiber DAS network for example). Either Ethernet port will support either LAN. The Guest LAN IP Address can be changed to support your requirement. Click on the checkbox next to Guest LAN, then click on Edit. A box will open where you can change the IP address.
Typical Connection Plan For the DSPMOD-CP-S/CDMA Donor Coax N Male to N Male IN CS05-102-429 10dB Directional Coupler OUT RX Diversity Port RX/TX Port (See Note) -10dB 820-2028-001 3' N Male to SMA Male Jumper CS54-3506-47 1' N Male to N Male Jumper 375-1014-001 Modem 2 – 820-2122-001 7' Ethernet Cable (Included) 375-1013-001 Switch Repeaters 2 – 820-2122-001 7' Ethernet Cable (Optional) Note: Donor must be connected to the RX/TX port only.
Typical Connection Plan For the DSPMOD-CP/CDMA Donor Coax N Male to N Male IN -10dB CS05-102-429 10dB Directional Coupler OUT RX Diversity Port RX/TX Port (See Note) 820-2028-001 3' N Male to SMA Male Jumper 375-1014-001 Modem 820-2122-014 14' Ethernet Cable CS54-3506-47 1' N Male to N Male Jumper Repeater Note: Donor must be connected to the RX/TX port only. Donor antenna, coax down lead and repeaters are sold separately.
Functionality Test You must be connected to the internet for the following steps. Once you’ve made your physical connections, connect your laptop to the internet and attempt to log in to the DSP over the air (through the modem). Remember, you will type in the IP address that Wireless Service Provider assigned to your modem, followed by a colon and the port number that is assigned to each protocol. Example: To access the Web UI, enter http://166.xxx.xx.
Right click on Local Area Connection - and select “Properties”. Scroll down and highlight “Internet Protocol (TCP/IP) and click on the “Properties” button. If you are set up to use DHCP, the window shown below will be displayed.
Select “Use the following IP address:” and enter “192.168.1.2.” The subnet mask should automatically populate to “255.255.255.0. While most devices automatically detect DNS, you can set the DNS to the settings shown on the Dashboard screen of the modem user interface. Default Gateway of computer has to = the IPAddress of the modem Preffered DNS servers = modem DNS Servers #1 Alternate DNS server = modem DNS Servers #2.
Nothing else will need to be chosen or entered. Click “OK”, then “OK” again and retry connection. A crossover Ethernet cable (supplied) must be used for Web Interface access. As a reminder, you must verify the Ethernet port on your laptop is powered. If your laptop is on battery power, the Ethernet port may be inactive by default. If this is the case simply plug in the laptop to a 110vac source or change the power settings to enable the Ethernet port when the laptop is using battery power.
Warranty This is a one year limited warranty. Seller warrants that its products are transferred rightfully and with good title; that its products are free from any lawful security interest or other lien or encumbrance unknown to Buyer; and that for a period of one year from the date of installation or fifteen months from the date of original shipment, whichever period expires first, such products will be free from defects in material and workmanship which arise under proper and normal use and service.
Notes -26-
Notes -27-
960-1147-003 rev A ECO 2707
