Operating instructions

IBR650 ( Industrial Broadband Router )
QUICK START GUIDE
1 )
What’s In The Box
SETTING UP THE ROUTER
Plug the power supply into an electrical outlet.
Connect Modem ( )Antennas
Connect the power supply to the IBR650.
Ensure power is switched on. o = OFF | = ON
2 )
3 )
FINDING YOUR PASSWORD
SPECIAL FEATURES
2 3 4
for more information about your product, visit:
www.cradlepoint.com
www.cradlepoint.com/IBR650
For additional information, visit:
Your unique default password is shown on the product label on the bottom
of your router. It is also the last eight characters of the MAC Address.
You will be asked for this password when you log into the administration pages.
The default password provides security for your router out-of-the-box.
find this label on the bottom of your router
IPSec VPN End-Point Support
GRE Tunneling
Data Usage Management & Alerts
GPIO Interface
GPS (if supported by modem carrier)
Failover / Failback
IP Passthrough
VLAN Support
AC Power Supply Quick Start Guide
PORTS & SWITCHES
Integrated Broadband Router
MODEMS/
DATA SOURCE
( WAN )
default
ETHERNET CONNECTIONS
POWER
12VDC
RESET
POWER
ON/OFF
POWER
LED
ATTN
LED
MODEM
LED
SIGNAL
STRENGTH
LEDS
MODEM
ANTENNA
CONNECTOR
MODEM
ANTENNA
CONNECTOR
MICRO
USB
MODEM ANTENNAS
( )
Model No.: IBR650
Part No.: IBR650
www.cradlepoint.com
H/W ver.: 1.0
MAC Address : 0030440c1fc1
Serial No.: MM100167900418
ESN (Hex): A1000010000557
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions (1) This device may not cause harmful interference and (2)This device must
accept any interference received, including interference that may cause undesired operation
Made in Taiwan
12V 1.5A
RoHS
MFG DATE: MAR 2011
Default Password: 440c1fc1
Contains FCC ID: N7N-MC5728
COMPUTERS
or LOCAL DEVICES
( LAN )
default
Mounting Bracket
IP PASSTHROUGH
To configure the IBR650 to run in IP Passthrough mode, please follow the steps below (after logging into router):
1) Select INTERNET in the top navigation menu.
2) Select CONNECTION MANAGER in the drop down menu.
3) Find the IP Passthrough section.
4) Select ENABLED, then click APPLY.
ACTIVATE YOUR MODEM
A wireless broadband data plan must be added to your IBR600. A new line of service can be added or a
data plan can be transferred from an existing account. Wireless broadband data plans are made available
from wireless carriers, such as Sprint and Verizon, and are required to allow your modem to connect and
transfer data on their network. You will need the ESN number from your product label on your router to
add or transfer a line of service. After adding a data plan to the modem, the modem may need to be
activated. To activate the modem, login to the IBR650 administration pages (see below) and select
Internet from the top navigation bar then Modem Settings from the drop-down menu, find and select the
CradlePoint modem and click Update/Activate, in the popup click Activate.
To add a broadband data plan, or to check if your modem has a broadband data plan attached, contact
the business you purchased the IBR650 from or your wireless service provider. For more information see
www.cradlepoint.com/IBR650.
USING THE FIRST TIME SETUP WIZARD
The First Time Setup Wizard will help you change passwords to something you choose, and establish a time zone.
1)
Open a browser window and type “cp/” or “192.168.0.1” in the address bar. PRESS ENTER/RETURN.
2)
When prompted for your password, type the eight character Default Password found on product label
(the last eight characters of the MAC Address).
3) When you log-in for the first time, you will be automatically directed to the FIRST TIME SETUP WIZARD.

Summary of content (2 pages)