INSTRUCTION MANUAL CZ-810
Thank you for purchasing the CZ-810 Massage chair. Before using your massage chair, please read the content of this instruction manual and refer to it when needed. Table of Contents Luxury Features ………………………........................…… 2 Safety Precautions ………………………......................…. 3-7 Chair Components ……………………….....................….. 8-9 Chair Installation & Moving ………………....................… 10-14 Chair Remote Controller …………………...................….. 15-16 Operation Guide …………………………...............
01 Luxury Features ● The operation of massage chair is controlled by a microcomputer that performs various intelligent massage methods and combinations, like Kneading, Tapping, Clapping, Shiatsu, Rolling, Vibration and Air Massage. All these methods massage acupressure points accurately to effectively alleviate fatigue, promote metabolism and improve blood circulation.
02 Safety Precautions IMPORTANT SAFETY INSTRUCTIONS When using the massage chair, basic precautions should always be followed, including the following: Read all instructions before using this massage chair. DANGER-To reduce the risk of electric shock: ● Always unplug this massage chair from the electrical outlet immediately after using and before cleaning. ● Never use pins or other metallic fasteners with this appliance. ● Carefully examine the covering before each use.
● To disconnect, turn all controls to the off position, then remove the plug from the outlet. ● Do not stand on or in the massage chair. Use only while seated. ● The product is not intended for use by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the product by a person responsible for their safety.
Caution ● This massage chair is to be used indoors only. ● If you use the massage chair in a cold room, do not increase the room temperature abruptly. It is recommended that you increase the temperature gradually to a normal level. ● If the massage chair is stored in a cold place and is being brought into a warm environment, it is advisable to wait one hour before use. This is because its performance may not be at optimum level, as there may be water droplets on the mechanical parts due to condensation.
3. People with Medical Conditions Consult your doctor before use if you: ● are under medical rest as ordered by a doctor. ● have spinal disorders, an abnormal spinal condition or have suffered a spinal injury. ● have back problems. ● have diabetes, osteoporosis or sensory impairment. ● have joint dysfunction such as rheumatism, hammertoe or gout. ● have a pacemaker or other electronic medical devices. ● may be pregnant. ● have phlebitis or thrombosis. ● have an increased risk for blood clots.
4. Instances When the Massage Chair Should Not Be Used In the following events, please switch off the main power switch immediately and disconnect the power cord from the electrical outlet: ● If water is accidentally spilled onto the massage chair. This may result in electric shock or malfunction. ● If the fabric of the backrest is torn and the internal components are exposed. ● If pain or discomfort is felt during massage, stop operation immediately and consult your doctor.
03 Chair Components Pillow Pad Shoulder Air Bags Controller Backrest Backrest Pad Armrest Air Bags Armrest Seat Pad Side Panel Calvesrest Wheet Legrest Footrest 8
Massaging Position 9
04 Chair Installation & Moving 1. When positioning the chair, please leave 80cm of space behind the backrest to allow free reclining of the backrest. 2. Unplug from outlet when installing the chair parts. Step 1: Take out below objects from 2 cartons. A: Chair Backrest and Seatrest part B: Chair Side panels Step 2: Insert and connect the backrest to the bottom seat, and fasten the backrest into the allocated slot. Note: Be careful of scratching during installation.
Step 3: Attach the connecting rod and the u stay fork of the reclining actuator with the flat head rivet, and secure with a split pin as demonstrated in PIC I and PIC 2. A: Connecting Rod ( On the backrest ) B: U stay fork of reclining actuator ( on the seat ) C: Flat head rivet D: Split pin A A D C C B B PIC 1 PIC 2 Step 4: Connect the plugs to the corresponding place in the seat according to the marks given. Note: Insert black to black and gray to gray, otherwise damage to the chair may result.
Step 6: Shoulder part Installation 1) Lock M6-screw onto Backrest by Round Spaner 2) Plug up screw hole with special plug head after well-connect shoulder part. Step 7: Side Panel Installation 1) Fix the side panels to the frame by the two “Z” hook. 2) Well connect the air pipes of armrest. 3) Fix the side panel by 4 socker cap screws, ensure the side covers can not move. 4) Fix the side connector and rotation part of backrest. 5) Install the controller holder.
Step 8: Connet the cover to the backrest with zipper. Step 9: Clip joint the pillow to the backrest cover. step 8 step 9 Step 10: Connect the wire plug. The back massage strength-control pad has been inserted into the backseat cover. If strong massage is desired, remove the back massage strength-control pad from the cover; this strengthens the massage. If mildermassage are desired, insert the back massage strength-control pad into the cover; this lessens the strength of the massage.
Chair Moving 1. Lift up the Calves Rest. 2. Then recline the chair to approximately to 45 degrees, so that you can easily move the chair around the house with a slight pull push. Note: a. Before you move the chair, please put the footrest back into the original position first. Otherwise, injuries might occur in the process of moving. b. Avoid moving the massage chair when there is someone seated on it. c.
05 Chair Remote Controller 13 14 15 16 17 19 20 21 18 41 34 11 30 36 1 28 37 26 38 12 39 10 9 2 4 3 5 6 7 22 23 24 25 40 15 32 33 31 35 29 27 8 16
06 Operation Guide Connect to the power supply, and turn the switch to “I” position. The chair is now in idle mode. During idle mode, there are only seven funtions: ON/OFF, Foot Extend, Pause, Recline, Sit Up, Lift Leg or Recline Leg that can be operated. CONTROL BUTTONS FOR THE MASSAGE CHAIR 1. ON/OFF The Start/Stop Control Button - Press once on this button and the backlight of the Remote Control will start blinking: the chair is in idle mode.
6/7. Length Adjustment Control Button for Legrest - These two control buttons can adjust the length on the legrest. - Press the button once to adjust the legrest to a comfortable length. Press the button again to confirm the length. 8. Length Auto Adjustment Control Button - It’s equipped with an Auto Function that length of footrest can be adjusted according to the user’s leg length for a more effective massage. Every time the button is pressed, the auto function will detect the best massage length. 9.
A. Full Body Auto Programme - If one of the five Auto Programmes is activated before the Auto Scan of the entire body, the machine will automatically do a height scan for the back. At the same time the user can manually adjust the massage height to the prefered level. The following are the Auto Programmes available: 13. Healthcare 14. Relax 15. Therapy 16. Smart 17. Circulation 18. Demo The Backrest and Footrest will resume original position when this Auto Programme is about to end. B.
23. Clapping Clapping function Start/Stop Control Button- 3 sizes of width, 5 levels of speed to be adjusted. - Press this button once to active the clapping function for a full back massage at medium speed. - Press the button again to stop the clapping massage function. 24. Shiatsu Shiatsu function Start/Stop Control Button- 3 sizes of width, 5 levels of speed to be adjusted. - Press this button once to active the shiatse function for a full back massage at medium.
30. Strength The Adjustment Button for Kneading Speed After activating the Kneading function, every time the button is pressed, the speed can be adjusted in the cycle. D. The spot or partial back massage 31. Spot The Spot or Localised Back massage. This button allows user to select Spot massage for any part on the back. - Press this button once to activate spot massage while the original massage mode continues to run at the original position.
E. Air-pressure for whole body 36. Neck Air Massage Neck Air Squeeze function Start/Stop Button- 5 levels of intensity to be adjusted. - Press once to activate pre-programmed Air-pressure Massage Mode to enjoy rhythmic air-pressure massage. - Press again to stop the function. 37. Shoulder Air Massage Shoulder Air Squeeze function Start/Stop Button- 5 levels of intensity to be adjusted. - Press once to activate pre-programmed Air-pressure Massage Mode to enjoy rhythmic air-pressure massage.
07 Grounding Instructions This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for the electric current to reduce the risk of electric shock. This product is equipped with a cord with an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
08 Chair Specification Description Specification Model No. CZ-810 Rated Voltage 110 - 120 ~ Rated Frequency 50/60 Hz Rated Power Consumption 250W Max Timer 5/10/15/20/25/30 minutes Max time rate 60 minutes Dimension(L x W x H) Weight Length of The Wire Usage Condition Storage Condition Safety Feature Packing size(Seat part): 52.4”x30.3”x37.2” Packing size(Backrest part): 35.4”x35.4”x14.2” Net Weight: 260lbs Gross Weight: 322lbs Controller wire: 1.3 m Power supply wire: 2.
09 Troubleshooting This massage chair is controlled by a microcomputer and is susceptible to power surges of +10 to –15%. The following situations may display in the event of a power surge: Situation Solution The massage chair is connected to the power supply but is not functioning. 1. Check to see that the plug is well connected and working. 2. Make sure that the massage chair switch is turned to the “I” position. The remote control works, but the massage chair is not functioning.
10 Product Care and Storage 1. Storing the Massage Chair ● Wipe off dust and dirty from the massage chair with a dry, soft, clean cloth after use. ● Keep the massage chair clean and away from places of high humidity. ● If the massage is not to be used for a long period of time, cover the massage chair with a dust cover and unplug its power plug from the electrical outlet. Caution ● Do not store the massage chair in direct sunlight or in places of high temperature.
11 COZZIA Consumer Warranty COZZIA products have the following warranty: COZZIA’s massage chairs, motion upholstery and home theater massage seating provide a one year in-home service warranty and a two-year parts warranty. COZZIA customer service will not issue Return Material Authorizations (RMAs) for products. COZZIA products will be either repaired by the consumer or by an in-home technician. COZZIA will not issue Return Material Authorizations (RMAs) for buyer’s remorse.
Canadian consumers may contact COZZIA's customer service department at 1-877-977-0656 between 9:00 am and 5:00 pm PST, Monday through Friday for warranty or service issues. ● Floor Models and Demonstration Units have a prorated warranty period that begins the day the model is placed on the floor and connected to an electrical outlet by the retail partner. Proof of purchase is required in order to obtain warranty service and parts. Non-warranty parts and service are available at a “per incident” charge.
● Fading, wear and piling of fabrics occurs naturally and does not constitute a defect under this warranty. ● Natural markings, grain and dye variations in leather do not constitute a defect under this warranty.
Warranty Card WARRANTY REGISTRATION FORM Product Serial No.
