2013 Red 40/Black 60 Scouting Camera Instruction Manual.
Table of Contents Camera button info diagram: (Fig. 1) ....................... 3 Installing the batteries: ............................................ 3 Installing the SD card: .............................................. 5 Understanding main screen info:............................. 6 Customizing the camera settings: ............................ 6 Page 2 Setting the camera mode: ....................................... 8 Camera mode settings: ............................................
Congratulations on your purchase of the 2013 Black 60/Red 40 Scouting camera! We truly value your business and will strive to provide you top quality customer service should you ever need help with any of our products. Check out our other products on our website at www.DLCcovert.com. Camera button info diagram: (Fig.
Installing the batteries: Black 60/Red 40 can function short term on 4AA batteries. Improved battery life on 8‐AA, but we suggest you use 12AA batteries to maximize camera performance and battery life. Using Covert 2300mAh, NiMH rechargeable AA batteries can extend the battery life significantly. Install the batteries by sliding the top battery in to the sleeve first, then depressing the spring with the other battery and snapping down in place.
Installing the SD card: To be able to power up the camera you will need to install a SD card in the slot in the bottom of the camera. See figure 3 below for card orientation. Push into the card slot until it clicks and release. To remove, repeat that process, the card will pop out enough to remove. You can use any SD card size up to 32G. You must have the SD card in the camera to be able to turn the camera on and set it up Figure 3 Page 5 .
Understanding main screen info: Camera/Video icon # of photos taken # of photos remaining on card Battery life indicator Page Mega Pixels chosen 6 Figure 4
Customizing the camera settings: Your camera is set to function with the default settings without any further customization. However, you will likely want to at very least set the clock and date. The following information will help you customize your camera settings so you can get the most out of the trail camera experience. To start, Press the MENU button once to open the customization menus. We will start with the CAM system tab. You will see CAM, PIR, and SYS tabs across the top of the screen.
Setting the camera mode: Press the ▼ button to highlight the Camera Mode option in yellow. Either Photo or Video will show up in a white box to the right. Press the ►button to toggle between Photo or Video until the option you want shows in the white box. Press OK. NOTE: If you do not press OK, your setting will return back to the previous setting. Camera mode settings: PHOTO SIZE: Press the ▼or ▲ button to highlight Photo Size in yellow.
Press the ▲ or ▼ buttons to highlight the PHOTO BURST option: To set this function, press the ►repeatedly to show the 1 Photo, 2 Photos, or 3 Photos option. Press OK to save the desired setting. Video mode settings: (Fig. 6) Figure 6 VIDEO SIZE: You can choose from WVGA(800x480), QVGA(320x240), 720P(1280x720) or 1080P(1920x1080) options. Page VIDEO LENGTH: You can adjust the length of time the camera takes a video from 5‐60 seconds. Press the ▲ or ▼ button to highlight the VIDEO LENGTH option.
change the number of seconds shown in the white box. Long videos fill the SD card up quickly. VIDEO SOUND: Your camera can record sound on videos. Press the ▼ button to highlight the Video Sound option. Press the ► button to toggle between On and OFF. Press the OK button to save the setting. PIR tab: Press the ▲ or ▼ buttons repeatedly until only the top tab PIR menu is highlighted in yellow. Press the ► or ◄ button to highlight the PIR tab in yellow. Screen should appear like Fig. 7.
easily. You can adjust the sensitivity of your camera to help with this. Under most conditions, the NORMAL option will work the best. In high temperatures, the HIGH setting might help differentiate between the outside temps and the body temps of the animal. In cold conditions, you may find that the LOW option is best as the camera can easily differentiate the outside temps from the body temps of the subject. If you are using the time lapse function, you would choose OFF to turn off the PIR.
have chosen your desired trigger interval, press the OK button to save the setting. Page TIME LAPSE: Press the ▼▲ arrow to highlight the Time‐Lapse option. This option allows your camera to automatically take a photo without being triggered by the PIR. If you already set the Sensitivity to OFF, then the camera will only take photos when the Time‐Lapse option is on. If you have the PIR set to LOW, NORMAL, or HIGH, the camera will also take photos when the PIR is triggered.
will fill the SD card up fast. Use max size SD card for best performance. START‐STOP: If you only want your camera to be on during part of the day each day you can set the Start‐Stop function. Press the ▲▼ buttons to highlight the Start‐Stop option. The default setting is OFF. Press the ► button to toggle the setting to ON and press OK. See Fig 8 & 9 below Once you press OK you will see the screen in Fig. 9.
time. You can press the ►◄ buttons to navigate back through the settings if necessary. Once you have the start‐stop times set, press OK to save the settings. SYS tab: The SYS tab controls all the internal system information such as Setting the clock, Time stamp, Flash range, Password, Over Write, and Format. (Fig. 10) Figure 10 Figure 11 Page 14 SETTING THE CLOCK: Scroll over to the SYS tab using the ►◄ buttons and then press the ▼ button to highlight the Set Clock option. Press OK.
Press the ▲▼ button to set the MONTH, the press the ► button to navigate to the DATE and use the ▼▲ buttons to set the date. Press the ► button to navigate to the year and set that using the ▲▼ buttons. Navigate down to the time using the ► button and follow the same process as above to set the time. Once you have the time set, press OK to save the settings. Page FLASH RANGE: You can set the Flash Range depending on your set up. If most of the subjects are going to be inside 20’, use the 6m/20ft setting.
the Flash Range option. Use the ► button to navigate between the two different settings. Press OK to save the settings. PASSWORD: Press the ▼ button to highlight the Password option. You can password protect your camera with this setting. The default setting is OFF. Make sure you write down your password or store it in your phone so you don’t lose it. If you set this option to ON, you will not be able to access your camera without the password. This is a very important security feature.
BEEP: If you want audio confirmation when you press the buttons, you can turn that ON or OFF with this option. Press the ▼ button to highlight the Beep option. Press the ► button to toggle between ON and OFF. Press the OK button to save the setting. OVER WRITE: The Over Write function will save new photos over the old photos on your SD card if it becomes full. Each time a new photo is taken the oldest photo on the card will be overwritten.
If you have a new SD card, you should always format the card before you use it in the camera. To format the SD card, press the ▼ button until the Format option is highlighted. Press the OK button. You will see a screen that has Yes and No on it, use the ► button to navigate to YES and press OK. DEFAULT SET: The Default Set option is the last option in the SYS tab. If you want to start clean and re‐set all the settings to the original factory default settings you will choose this option.
DEL button. This will delete the photo that is showing on the screen. You will see the screen below. Use the ► button to navigate to YES and press OK. If you do not want to delete, press the DEL button again to exit. (Fig. 13) Figure 13 Page MINI USB: Your camera comes with a mini USB cable to hook up to your computer or TV to look at the photos. Plug the small jack of the cable into the bottom of the camera. Plug the USB end into the USB port on your home computer or USB capable television.
hardware and download the proper driver to view the images or videos. The screen on the camera will say Mass Storage. If the image files don’t automatically open, you will need to open it using Windows Explorer to locate the camera. It will appear as a removable disk. For best results, mount the camera approximately 4 feet off the ground facing straight forward as level as possible.
Use the Covert Tree60 mounting system to mount the camera up higher pointing down on them for a better look. Works great when you don’t have a straight tree to attach to. Www.dlccovert.com. Troubleshooting: ISSUE: Camera will not turn on. POSSIBLE PROBLEM: No SD card in the card slot Corrupt SD card Batteries are too low to power up camera POSSIBLE SOLUTION: If you are still having problems with your Black 60/Red 40 contact Customer Service at 877‐462‐ 1799 or e‐mail us at support@dlccovert.
IMPORTANT NOTE: If you have problems, do not contact the retail store you purchased the product from, contact us and we will be happy to take care of you. Warranty: DLC Covert warranties this product for a period of 1 year from the date of purchase. This warranty only covers manufacturer’s defects and does not cover damage caused by misuse or abuse of the product. If you have problems with this product, please do not contact the store you purchased it from.
Page 1. Repair the product by means of telephone support, E‐mail or depot service at no charge for parts or labor, shipping prepaid by customer, return shipping prepaid by Covert. (US only) Return shipping to be billed to customer and must be paid prior to shipping, if camera is not found to be defective in materials or workmanship. 2. Replace the product with a comparable product which may be new or refurbished. (Warranty is not extended beyond original purchase date.) 3.
to Telephone Support personnel to resolve issues If telephone support is unsuccessful, Covert or its authorized dealer will instruct the customer on how to receive warranty repaid as provided below. Covert reserves the right to charge for service in exception cases. A description of the depot process may be obtained from the authorized Covert reseller/distributor. Depot service is at Covert’s or 24 Service is available in the United States.
it’s authorized dealer’s sole discretion and is considered an option of last resort. In the maintenance of the product, Covert may use new or equivalent to new parts, assemblies or products for equal or improved quality. All defective parts, assemblies, and products become the property of Covert. Covert may require the return of parts, assemblies and products to a designated Covert Depot or the Covert representative from which the part, assembly, or product was originally purchased.
d. e. f. 26 c. Page b. the product unless directed by a Covert representative. To repair damage, malfunction or degradation of performance resulting from improper use or connection to incompatible equipment or memory. To repair damage, malfunction, or degradation of performance caused by the use of non‐Covert supplies or consumables or the use of Covert supplies not specified for use with this product.
Page Any service identified in the above list and provided by Covert at the Customer’s request shall be invoiced to the customer, at Covert’s then current rates for parts, labor and shipping. 27 meeting the operating specifications set forth in the user manual. g. To repair damage, malfunction or degradation of performance resulting from failure to properly prepare and transport the product as prescribed in published product materials h.
TO THE EXTENT ALLOWED BY LOCAL LAW, EXCEPT FOR THE OBLIGATIONS SPECIFICALLY SET FORTH IN Page Some states, provinces, and countries do not allow the exclusion or limitation of incidental or consequential damages or exclusions or limitation on the duration of implied warranties or conditions, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary by state, province, or country.
Page 29 THIS WARRANTY STATEMENT, IN NO EVENT SHALL COVERT AND ITS VENDORS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF PROFITS) WHETHER BASED ON CONTRACT, TORT, OR ANY OTHER LEGAL THEORY AND IRRESPECTIVE OF WHETHER COVERT OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
