Cov lus qhia
FEATURE DETAILS (FIG. A)
5
Klein Tools Accessory Slots
(60447 only, ×2)
13a
Outer Suspension Bracket (×4)
6
Pivot Adjustment (×2)
13b
Center Suspension Bracket (×2)
7
Size Adjustment Knob
13c
Center Bridge Tab (×4)
8
Rear Neck Pad
14
Bracket Key (×4)
9
Suspension
Anchor Points (×6)
15
Bracket Key Slot (×20)
10
Washable Sweatband
16
Metal Anchor (×6)
11
Washable Top Comfort Pad
17
Rivet (×6)
12
Suspension Straps (×6)
FITTING (FIG. B)
All hard hats come with suspension pre-installed at factory settings.
The suspension can be adjusted to ensure proper and secure fit to
your head for maximum protection. Follow the steps below:
STEP 1: Turn the Size Adjustment Knob
7
counterclockwise to
loosen the fit. Position the Rear Neck Pad
8
on the back of your
head, closer to the neck. Dress any bandana knots or ponytails over
the rear neck pad
8
.
STEP 2: Tighten by turning the
Size Adjustment Knob
7
clockwise until the hard hat is comfortable and snug. Move your
head up, down and side-to-side gently, like you would normally,
and make sure the hard hat stays on. Make sure that the hard hat
is not angled forward or backward, but rests level on your head.
ADJUSTMENTS
If the hard hat does not fit properly at the factory settings, you
can further adjust the fit:
STEP 1: Separate the Outer Suspension Bracket
13a
from the
Center Suspension Bracket
13b
by pulling back gently on the Outer
Suspension Bracket
13a
to release the Center Bridge Tab
13c
. Do this
on all four Bracket locations before moving to the next step. (FIG. C).
STEP 2: Determine which Bracket Key Slot
15
you wish to reattach
to. Using the slots deeper in the hard hat will move frame higher
on the head, and vice versa. Turn the Outer Suspension Bracket
13a
approximately 90° to release the Bracket Key
14
from the Bracket
Key Slot
15
. Insert the Bracket Key
14
into the new slot location
and rotate the Outer Suspension Bracket
13a
back approximately
90° to secure. Always match the settings on the left and right
sides to prevent the suspension from sitting at an angle.
STEP 3: Secure the Outer Suspension Bracket
13a
by snapping
back the Center Bridge Tab
13c
in a total of four locations before
moving to the next step.
STEP 4: Verify the hard hat fits properly. Follow the steps in the
FITTING section to ensure proper fit. Ensure that accessories
you plan to use fit and function properly while maintaining the
hard hat’s ability to perform its function optimally. Check with a
qualified safety expert if unsure.
SUSPENSION REPLACEMENT
NOTE: It is recommended that you wear hand protection
when performing actions in this section.
STEP 1: Separate the Outer Suspension Brackets
13a
from the
Center Suspension Bracket
13b
by pulling back gently on the Outer
Suspension Brackets
13a
to release the Center Bridge Tab
13c
. in a
total of four locations before moving to the next step. (FIG. C)STEP
2: Place your thumbs under the Outer Suspension Brackets
13a
and
push upwards. This will release the Metal Anchor
16
from the Rivet
17
in six locations (FIG. D). DO NOT push on the Metal Anchors,
as this could cause injury or deform the anchor.
SUSPENSION REPLACEMENT
STEP 3: On the replacement suspension, determine which Key Slot
15
you want to reattach to. Turn the Outer Suspension Bracket
13a
approximately 90° to release the Bracket Key
14
from the Key Slot
15
. Insert the Bracket Key
14
at the new slot location and rotate the
Outer Suspension Bracket
13a
back approximately 90° to secure.
Always match the settings on the left and right sides to prevent the
suspension from sitting at an angle.
STEP 4: Secure the Outer Suspension Brackets
13a
by snapping
back the Center Bridge Tabs
13c
in a total of four locations before
moving to the next step (FIG. C).
STEP 5: Position the Metal Anchor(s)
16
on top of the Rivet(s)
17
and gently pull on the Suspension Straps
12
until the Metal
Anchor(s)
16
are properly seated. Make sure all six Metal
Anchor(s)
16
are properly seated on the Rivets
17
and are all at the
same level (FIG. E).
STEP 6: Verify the hard hat fits properly. Follow the steps in the
FITTING section to ensure proper fit. Ensure that accessories you
plan to use fit and function properly while maintaining the hard
hat’s ability to perform its function optimally. Check with a qualified
safety expert if unsure.
NOTE: DO NOT pull on the suspension straps to free the
anchor. This could permanently damage the anchors and
straps, preventing them from performing as intended.
NOTE: The suspension strap lengths are fi xed and cannot
be adjusted. DO NOT attempt to alter.
SWEATBAND AND TOP COMFORT PAD (FIG. F)
Klein Tools hard hats come with an advanced sweatband
and top comfort pad designed to wick away sweat. They are
machine washable in a normal wash cycle. Do NOT wash with
bleach or with detergents containing bleach. Machine dry on
normal or low heat setting only.
The sweatband and top comfort pad can be easily removed
and reinstalled on the suspension:
• The top comfort pad is held in place by a single Hook-and-
Loop pad
24
.
• The sweatband is held in place by four Suspension Hooks
25
and three Hook-and-Loop Pads
24
,
on the side and front. To
remove, simply detach all Hook-and-Loop pads and slide the
sweatband off the suspension hooks.
56062 HEADLAMP (60447 ONLY) (FIG. G)
The optional 56062 is a rechargeable headlamp designed
specifically for Klein hard hats that have the integrated front
and rear Accessory Slots
5
. It functions as a spot light or
flood light, and has magnet to attach onto magnetic surfaces
for use as a worklight. Charging cable is included with
models that include rechargeable headlamps.
18
On/Off/Mode button
21
Magnet
19
Spot light
22
Pivoting mount
20
Flood lights
23
Release tab
The 56062 can be attached to both the front and back of the hard
hat via the Klein Tools Accessory Slot
5
. It can be tilted up to 64°
on the hard hat, or stand alone as a worklight.
To install the headlamp, align the Pivoting Mount
22
with the Klein
Tools accessory slot
5
on the hard hat and push down until the
headlamp clicks securely into place.
To remove the headlamp, press forward on the Release Tab
23
, and
lift the headlamp out of the Accessory Slot
5
.
STICKERS
WARNING: Klein Tools DOES NOT approve the application
of stickers, hot stamps, inks, or foils that have metallic
content to this hard hat by end users. Such modifi cations
can alter the performance of the hard hat.
www.calcert.com sales@calcert.com1.888.610.7664
0
5
10
15
20
25
30